Dacor REMP16 Technical manual

PLANNING
GUIDE
Web: http://www.Dacor.com
Corporate Phone: [phone]
Specifications are subject to change without notice.
See installation instructions for additional details. 9.3
Remote Blowers
REMP3, REMP16
1/3
Revised
01/30/09
REMP3 OVERALL DIMENSIONS
(Top & Side Views)
17 3/8" (441mm)
19" (483mm)
24 1/4"
(616mm)
3 5/8"
(92mm)
2 1/8"
(92mm)
9 1/4"
(235mm)
Mounting
Flange
25 1/2"
(648mm)
7 1/2"
(191mm)
4"
(102mm)
9 1/2" (241mm)
Discharge
Cutout Location
11”W x 12 5/8”H
(279mm X 321mm)
Intake Collar
Power Supply
Conduit Hole C
L
C
L
C
L
C
L
5 13/16"
(148mm)
8" Nom.
(203mm)
7 15/16"
(202mm)
Discharge
Intake Collar
REMP16 OVERALL DIMENSIONS
(Top & Side Views)
26" (660mm)
32 1/4"
(819mm)
3 5/8"
(92mm)
2 1/8"
(54mm)
12 1/4"
(311mm)
Mounting
Flange
33 1/2"
(851mm)
9 1/2"
(241mm)
4"
(102mm)
13 1/8"
(333mm)
Discharge
Cutout Location
13”W X 16 5/8”H
(330mm X 422mm)
Intake Collar
Power Supply
Conduit
Location
C
L
C
L
C
L
C
L
24 1/4" (616mm)
9 9/16"
(243mm)
10" Nom.
(254mm)
11 1/2"
(292mm)
Discharge
Intake Collar
WARNING
1. Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
2.
This appliance must be installed in accordance with the
accompanying installation instructions.
+/- 1/16” (+/- 1.6mm) unless otherwise stated
Model No.
Electrical Supply
Requirments
Maximum Duct
Length
Total Connected
Load Blower Rating*
Approximate
Shipping Weight Finish
REMP3 Refer to raised
vent or hood
specifications
Refer to raised
vent or hood
specifications
120 Vac, 3.8 Amp 600 CFM (nominal)
620.5 CFM (actual) 35 lbs.
Galvanized
(may be painted)
REMP16 120 Vac, 2.7 Amp 1000 CFM (nominal)
994.8 CFM (actual) 55 lbs.
* At 0" static pressure

PLANNING
GUIDE
Web: http://www.Dacor.com
Corporate Phone: [phone]
Specifications are subject to change without notice.
See installation instructions for additional details. 9.4
Remote Blowers
REMP3, REMP16
2/3
Revised
01/30/09
Airflow CFM (Cubic feet/minute)
Static pressure - inches of water
0
1.0
2.0
3.0
4.0
5.0
100 200 300 400 500 600 700
REMP3 Blower Performance
Airflow CFM (Cubic feet/minute)
Static pressure - inches of water
0
0.5
1.0
1.5
2.0
2.5
200 400 600 800 1000
REMP16 Blower Performance

PLANNING
GUIDE
Web: http://www.Dacor.com
Corporate Phone: [phone]
Specifications are subject to change without notice.
See installation instructions for additional details. 9.5
Remote Blowers
REMP3, REMP16
Blower
discharge
Roof curb
Prevailing
wind
REMP FLAT ROOF INSTALLATION
(Top & Side Views)
25 1/2"
(648mm)
2"
(51mm)
19"
(483mm)
23 1/4"
(591mm)
6"
(152mm)
2"
(51mm)
REMP3
ROOF CURB DIMENSIONS
NOTE:
1. The REMP chassis may be rotated to clear
obstructions. 15” (381mm) min. clearance must
be maintained from the air discharge to any
obstruction. When mounting in a horizontal
position, shield the REMP to protect from possible
water collection in the chassis. Maintain a
minimum down slope of 1/4” (6mm) per foot for
evacuation of water.
2. When the REMP is installed on to a flat (less than a
2:12 pitch) roof, a roof curb is required.
3. The blower discharge must be pointed in the same
direction as the prevailing wind.
3/3
SAMPLE REMP ROOF INSTALLATION
(Side View)
Blower
Roof
Discharge
Blower
Duct
Wiring/Conduit
Wiring/Conduit
Duct Wall
No obstructions
within 15 inches of discharge
Discharge
33 1/2"
(851mm)
2"
(51mm)
26"
(660mm)
30 1/2"
(776mm)
6"
(152mm)
2"
(51mm)
REMP16
ROOF CURB DIMENSIONS
*All the CFM Blower Ratings are valued at 0” (zero-inch) static pressure.
Revised
06/11/08
+/- 1/16” (+/- 1.6mm) unless otherwise stated