Dado Lab HP5 User manual

Stack Emission
dado lab HP5 User Manual

ENGLISH | iii
Index
1 General Rules 1
Receiving Goods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Sampling Probe
3 HUB
2 FC5 Condenser

I| HP5 User Manual
1 General Rules
Receiving the goods
Remove the instrument from packaging and verify
immediately the integrity and presence of the
content.
Important :
In case of damages of the packaging, a note to the
courier must be immediately written on the trans-
port papers supplied they will ask you to sign. If the
note it’s not carried out, no claims for refunding or
replacing the instrument will be accepted.
Any damage observed after unpacking must be
notied within 8 days from receiving the goods and
a written communication to the delivery company
must be sent considering them responsible for any
consequence.
Test
Test and calibration are carried out in Dado Lab
facilities, at the end of test, a report with test and
calibration results will be produced and given to the
customer.
To request a test in your facility, please contact your
local dealer. .
Warranty conditions
Warranty cover a period of 12 months from the day
you receive the goods or from test in your facility (if
applicable).
Disposable or rechargeable batteries have a 6
months warranty.
Consumable materials, such as components which
have to be replaced periodically during the instru-
ment lifetime (protection lters, fuses, lamps etc) are
not covered by warranty.
Warranty exclusion/limitation
Dado Lab takes no responsability for damages
caused by external factors, unvolontary damages, im-
proper use, modications of the instrument or use of
third party devices, negligency, improper transport
or loss caused by shipping back the instruments, in
those cases, warranty will not be applied.
Moreover, warranty expires in case of service or
maintenance not carried out by Dado lab or non
authorized dealers.
Warranty is limited to the value of the purchased
instrument. .
In case of malfunctioning, please contact your local
dealer or [e-mail]

| 1
Conformity
Safety and CE mark
Dado Lab declares that the instrument is in compli-
ance to the following safety :
Low Voltage devices Directive BT 2014/35/UE
Directive 2011/65/UE ROHS - Restriction of
Hazardous Substances Directive
Directive EMC 2014/30/UE for the electromag-
netic compliance (EMC)
Machinery Directive 2006/42/EC
Sampling methods
Dado Lab declares the instrument is compliant to
the followng standards and rules for the sampling :
Emissions
UNI EN 16911-1
Measurement of stationary source emissions —
Manual and automatic determination of velocity
and volumetric ow in ducts - Part 1 : Manual
reference method
UNI EN 13284-1:2003
Stationary source emissions – Determination of low
range mass concentration of dust – Part 1: Manual
gravimetric method.
UNI EN 1911
Stationary source emissions - Determination of
mass concentration of gaseous chlorides expressed
as HCl - Standard reference method
UNI EN 14385
Stationary source emissions – Determination of the
total emission
of As, Cd, Cr, Co, Cu, Mn, Ni, Pb, Sb,Tl and V
UNI EN 13211
Air quality. Stationary source emissions - Manual
method of determination of the concentration of
total mercury.
UNI EN 13649
Stationary source emissions. Determination of the
mass concentration of individual gaseous organic
compounds. Activated carbon and solvent desorp-
tion metho.d
EN 1948-1
Stationary source emissions
Determination of the mass concentration of
PCDDs/PCDFs and dioxin-like PCBs
Part 1: Sampling of PCDDs/PCDFs
Safety rules for the use
To correctly use the instrument, please follow care-
fully the safety indications :
1. Do not remove, for any reason, any part of the
device without having disconnected before the
power supply.
2. Always use protected and grounded power sup-
ply.
3. Do not use the HP5 outdoor wihout having
ready a good protection for rain conditions or
possible sources of humidity
4. Max operating temperature : 400 °C.

2| HP5 User Manual
2 Sampling
Probe
Installing the Pitot tube and Nozzle
Install the Pitot tip and place the stack thermocou-
ple as indicated in the picture here below.
Mount the gooseneck curve aligned to the Pitot tip.

ENGLISH | 3
2 3
1
Dp-
Dp+

4| HP5 User Manual
3 HUB
Connection of the Hub to the probe
and umbillical cable
Unscrew the four allen screws which close the probe
locking clamp.
Remove the inner tube and place the probe, with
the desired position, on the support. Check the
position using the correct positioning of the refer-
ence screw.
Lock again using the clamp and the four allen
screws. Place the inner tube.

ENGLISH | 5
Electrical and pneumatic connections
1. HUB power supply socket, connect the umbili-
cal cable plug.
2. HUB thermocouple (heated lter) socket, con-
nect to the umbilical cable.
3. Probe power supply plug, connect to the umbili-
cal cable
Dp - Pitot dierential pressure connecor, nega-
tive signal, connect to the umbilical cable.
Dp+ Pitot dierential pressure connecor, posi-
tive signal, connect to the umbilical cable.
321
Dp-
Dp+

6| HP5 User Manual
4 FC5 Condenser
Connections
1. Gas inlet from the lterholder. e connection
tube can be made of titanium or glass, Il giunto
di collegamento pù essere realizzato in Titanio
e/o Vetro, this one can be used only the glass
lterholder.
2. Gas outlet, to be connected with a silicon tube
to the position n° 5.
3. Cooling liquid inlet.
4. Cooling liquid outlet.
5. Umbilical cable quick connector.
6. Condense ask, 1 liter, with GL45 connector
7. Velcro strip to x the umbilical cable
8. Condensation gas thermocouple, connect to the
umbilical cable.
2
1
4
35
6
8
7

ENGLISH | 7
5 500 cc
impingers
Spare parts code
1. Bottle 500 cc - PR02 GL 302
2. Free tube - PR02 GL 303
3. Plate tube - PR02 GL 304
4. PTFE/Silicon ring GL25 - PR00 FJ 002
5. Cap w/ hole GL25 - PR00 FJ 001
6. 90° Elbow - PR02 GL 302
7. PTFE/Silicon ring GL18 - PR00 FJ 004
8. Cap w/ hole GL18- PR00 FJ 003
9. Elbow w/ hosebarb - 101 103 2013
2
4
1
5
3
4
1
5
6
7
8
4
5
9

8| HP5 User Manual
Assemble of 6/4 500cc impingers

ENGLISH | 9
2. PTFE/Silicon ringGL18 d8 - PR00 FJ 004
3. Kit of 10 Silicone gaskets (Tmax 200°C)
PN 101-102-1450
3a Kit of 10 Silicone gaskets (Tmax 350°C)
PN 101-102-1451
6 Filterholders
Spare parts code
1. PTFE/Silicon ring GL18 - PR00 FJ 004
12
2
3
1