DAELECTRONICS ICTRL-R-MINI User manual

[email protected]
da_electronics
daelectronics pedals
daelectronicscontroller
DAeLECTRONICS
www.daelectronics.com
ed usarlo al meglio per molto tempo. Conservate
questo manuale per la consultazione quando sarà
necessaria.
Thank you very much for purchasing the
DAeLECTRONICS iCtrl-R mini. Please read this
manual carefully to learn about all the functions of the
iCtrl-R mini so that you will be able to use it fully for
a long time. Keep this manual in a convenient place for
reference when necessary.
MANUALE D’USO – OPERATIONAL MANUAL
3
3
1
pocket MIDI CONTROLLER
iCtrl-R-mini
Grazie per aver acquistato il DAeLECTRONICS
iCtrl-R mini. Per favore leggete questo manuale con
cura per imparare tutte le funzioni dell’iCtrl-R mini

1

3
iCtrliCtrl--R miniR mini
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
2
can now select between 4 slots pushing one of the controller buttons (the related red will switch on while led 1 will still blink).
You can send control changes to switch on/off effects inside the slots as follows:
control change 01 long click and release of switch 1 blue led 5 on > cc 17
control change 02 long click and release of switch 2 blue led 6 on > cc 18
control change 03 long click and release of switch 3 blue led 7 on > cc 22
control change 04 long click and release of switch 4 blue led 8 on > cc 26
Now pressing one of the switches of the related performance mode will be selected. The calibration values will be stored until the
next calibration.
Performance 1
Holding for 2 second button 1 while other performance are activated performance 1 will be activated (led 1 blinking and all other leds off). You
Warning and Calibration
Warning: pay much attention when insert and remove your USB cable from the iCtrl-R Mini input. You could damage it irreparably!!!
Calibration: at the startup, after led check, the controller will start the waiting mode (all red led on).
Pushing button 1 to 4 the related performance will be activated or holding button 1 for one second the calibration mode will be activated (blue led
led blinking)
Before ou start using the Expression pedal (the pedal shall ALWAYS be disconnected / connected to the controller before energizing the controller
itself)
Immediatel after entering the calibration mode, depress the pedal backwards to the minimum heel setting then sweep to the maximum toe
setting, this will ensure ou calibrate our pedal with the

Performance 2
Holding for 2 second button 2 while other performance are activated performance 2 will be activated (led 2 blinking and all other leds off)
You can now select between 4 slots pushing one of the controller buttons (the related red will switch on while led 2 will still blink)
You can now send control changes to switch on/off effects inside the slots as performance 1 a ove.
Performance 3
Holding for 2 second button 3 while other performance are activated performance 3 will be activated (led 3 blinking and all other leds off)
You can now select between 4 slots pushing one of the controller buttons (the related red will switch on while led 3 will still blink)
You can now send control changes to switch on/off effects inside the slots as performance 1 a ove.
Performance 4
Holding for 2 second button 4 while other performance are activated performance 4 will be activated (led 4 blinking and all other leds off)
You can now select between 4 slots pushing one of the controller buttons (the related red will switch on while led 4 will still blink)
You can now send control changes to switch on/off effects inside the slots as performance 1 a ove.
3

Leds Syncronizing
Syncronizing the iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini with FX inside patch.
With this option for each of the 4 slot of the kemper performance you can sync the on/off status of leds on the mini with the on/off status of the
effects inside kemper slots.
Leds com ination will e then saved and recalled every time a kemper slot is selected.
To set up and save combination of the 4 effects for each patch :
1. Let’s make sure leds on the iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini are in s nc with our effect on/off states in that patch on our software/daw/rack . Do this b
turning all the iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini led lights off, b stepping on the buttons. Now also off all our effects from within our software/daw/rack
2. Turn on the effects ou want saved in our patch, do this with the buttons on the iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini , so the light up, don’t do it inside ou
software/daw/rack.
3. Save the setting on the iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini b holding down button related to the blinking red led for 2 second
4.After saving the setting on the iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini save our patch in our software/daw/rack in the same state
5. Select switch 2 and repeat the process for all 4 switches and ou iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini will be totall in s nc with our gear.
4

5
Vslider
It’s a motion detection sensor located on the right side of the box that is always active and communicates via the control change # 1 (values
from 01 to 127).
With this sensor you can send continuous MIDI CC by moving back and forth the foot or the hands from the sensor. Led #9 will be off (a CC #55 with
value =0 will be sent) after 800ms when you move away the foot or the hand from the sensor. Led #9 will be on and a CC #55 with value =127 will
be sent after holding the foot in front of the sensor for 800ms. You can then switch on off an effect to be controlled by the Vslider assigning CC
#55to it.
127). In addition when the pedal is set at minimum heel a CC #66 with value =0 will be sent after 800 millisecond, a CC #66 with value =127 will be
sent when the pedal is at maximum toe setting after 800ms. You can then switch on off an effect to be controlled by the expression pedal assigning
CC #66 to it.
External Expression pedal
When an expression pedal is connected to an iCtrl-R mini, it will be always active and communicates via the control change #7 (values from 01 to

APPENDI
iCtrliCtrl
iCtrl-
--
-R mini
R miniR mini
R mini . You can connect with a MicroUSB ca le (just plug into the jack) and the iCtrl
iCtrliCtrl
iCtrl-
--
-R mini
R mini R mini
6
R mini will
power up or use the recharga le attery. When the USB power is powered, it will automatically switch over to USB for power, as well as start
charging the battery. This happens 'hotswap' style so you can always keep the attery as a ' ackup' power that will only get used when USB
power is lost.
When the attery is charging you can see a yellow led on through the USB hole on the ox side.
Switch in the down position the toggle switch when the USB ca le is removed and you don’t use the controller, the attery circuit will e switched
off.
When fully charged (10 hours under USB power) attery will last for approx 16 hours.
Bluetooth
iPad & iPhone
Download the app for iPad/iPhone https://itunes.apple.com/it/app/bluetooth-midi-connect/id1108321791?mt=8
Open the app and select iCtrl-R Mini Bluetooth > Connect
Go to the App to be controlled (JAM UP, AMPLITUBE and other) and enjoy it ;)
For Mac, you need to launch the Audio MIDI Setup utility from within OS ’s Utility folder (Finder>Applications>Utiltiies>Audio MIDI Setup).
Then press CMD + 2 to open the MIDI studio (or navigate to Window>Show MIDI Studio). Double click the Bluetooth module and press the
“connect” button next to your iCtrl-R mini that appears in the window.
Power Management (on Bluetooth versions)
There're two ways to power the

DAeLECTRONICS
MADE IN ITALY
www. dae lectr on ic s .c om