Daewoo Dadh0810 User manual

Manufactured under license of Daewoo International Corporation, Korea

www.daewoopowerproducts.com

USER'S MANUAL

DADH0810

Demolition Hammer

1. MAIN PARTS DESCRIPTION

Warning: Read, undestand and follow all safety rules and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious

injury.

2. GENERAL SAFETY RULES

Warning: Read all instructions. Failure to follow all instructions listed below may result in electric

shock, fire and/or serious personal injury.

SAVE THE INSTRUCTIONS

The term “power tool” in all of the warnings listed bellow refers to your mains operated (corded)

power tool or baterry operated (cordless) power tool.

1.Workplace

1) Keep workplace clean and well lit.

Cluttered and dark workplaces invite accidents.

2) Do not operate power tools in explosive atmospheres, such as in the presence of flam-mable

liquids, gasses or dust. Power tools create sparks which may ingnite the dust or fumes.

3) Keep children and bysteanders away while operating a power tool. Distractions can cause you yo

lose control.

2. Electrical safety

1) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodifed plugs and matching outlets will reduce risk

of electric shock.

2) Avoid body contact with earth or grounded surfaces such as conduits, radiators, and refrigera-

tors. There is an increased risk of electric shock if your body is earthed or grounded.

3) Do not expose power tools to rain or wet conditions. Water entering a power tools will increase

the risk of electric shock.

4) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat oil, sharp edges or moving parts. Damaged or entangled cord increase

the risk of electric shock.

5) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

3. Personal safety

1) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not

use a power tool while you are tired or under the influence of drugs, alcohol or medica-tion. A

moment of inattention while operating power tools may result in serious personal injury.

2) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

3) Avoid suddenly starting. Ensure the switch is in the off position before plugging in. When your

finger on the switch or plugging in power tools that have the switch on invited accidents.

4) Remove any adjusting key or wrench before turning the power tool on. A wrench or a kay left

attached to a rotating part of the power tool may result in personal injury.

5) Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unecpected situations.

6) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

7) If devices are provided for the connection of dust extraction and collction facilities, ensure these

are connected and properly used. Use of these devices can reduce dust related hazards.

4. Power tool use and care

1) Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it was designed.

2) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

3) Disconnect the plug from the power source before making any adjustments, changing, acces-

sories, or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

4) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

5) Maintain power tools. Check for misalingnment or binding of moving parts, breakage of parts any

other condition that may affect the power tools operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained power tools.

6) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in

the manner intended for the particular type of power tool, taking into account the working condici-

tons and the work to be performed. Use of the power tool for operations different from those inten-

ded could result in a hazardous situation.

5. Battery tool use and care

1) Recharge only witch the charger specifed by the manufacturer. A charger that is suitable for one

type of battery pack may create a risk of fre when used with another battery pack.

2) Use power tools only witch specifically designated battery packs. Use of any other battery packs

may create a risk of injury and fire.

3) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fre.

4) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact acci-

dentally occurs, fush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

6. Service

1) Have your power tool serviced by a qualifies repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

3. ADDITIONAL SAFETY RULES

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence

to hammer safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal

injury.

1. Wear ear protectors. Exposure to noise can cause hearing loss.

2. Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

3. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool

may contact hidden wiring or its own cord. Contact while a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

4. Wear a hard hat (safety helmet), safety glasses and/or face shield. Ordinary eye or sun glasses

are NOT safety glasses. It is also highly recommended that you wear a dust mask and thickly

padded gloves.

5. Be sure the bit is secured in place before operation.

6. Under normal operation, the tool is designed to product vibration. The screws can come loose

easily, causing a breakdown or accident. Check tightness of screws carefully before operation.

7. In cold weather or when the tool has not been used for a long time, let the tool warm up for a while

be operating it under no load. This will loosen up the lubrication. Without proper warm up, hamme-

ring operation is difficult.

8. Always be sure you have a firm footing. Be sure no one is below when using the tool in high

locations.

9. Hold the tool firmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool only when hand-held.

12. Do not point the tool at any one in the area when operating. The bit could fly out and injure

someone serioudly.

13. Do not touch the bit or parts close to the bit immediately after operation; the may be extremely

hot and could burn your skin.

14. Do not operate the tool at no-load unnecessarily.

15. Some material contains chemical which may be toxic. Take caution to prevent dust inhala-tion

and skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS

Warning: Misuse or failure to follow the safety rules started in this instruction manual may cause

serious personal injury.

4. OPERATION

Installing or removing bit

1. Bit

2. Change ring

Important: Always be sure that the tool is switched off and unplugged before installing or removing

the bit. Pull the change ring down all the way and insert the bit into the tool holder as fas as it will

go. Release the change ring and it will return automatically to its original position to secure the bit.

After installing, always make sure that the bit is securely held in place by trying to pull it out. To

remove the bit, pull the change ring down all the way and pull the bit out.

Side grip (auxiliary handle)

1. Side handle (auxiliary handle)

2. Grip base

The side grip swings around to either side, allowing easy handling of the tool in any position. Loosen

the side grip by turning it counterclockwise, swing it to the desired position and then tighten it by

turning clockwise.

Switch action

1. Lock button

2. Switch

CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly

and returns to the “OFF” position when released.

To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull

the trigger and then push in the lock button. To stop the tool from the locked position, pull the

trigger fully, then release it.

Chipping / Scaling / Demolition

Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that

the tool will not bounce around, uncontrolled. Pressing very hard on the tool wiil not increase the

efficiency.

5. MAINTENANCE

CAUTION: always be sure that the tool is switched off and unplugged before carrying ot any work

on the tool.

Replacement of carbon brushes

Whenever carbon brushes must be replaced, they cut out the tool automatically. When this occurs,

loosen the bolts which secure the rear cover. Remove the rear cover. Then replace both carbon

brushes at the same time. Use only identical carbon brushes.

Lubrication

This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system.

Lubricate the tool every time the carbon brushes are replaced.

Run the tool for several minutes to warm it up. Switch off and unplug the tool. Remove the crank cap

using oringial lock nut wrench (optional accessory). Rest the tool on the table with the bit end

pointing upwards. This will allow the old grease to collect inside the crank housing. Wipe out the old

grease inside and replace with a fresh grease (30 g). Use only original genuine grease (optional

accessory). Filling with more than the specified amount of grease (approx. 30 g) can cause faulty

hammering action or tool failure. Fill only with the specified amount of grease. Reinstall the crank

the cap excessiveely. It is made of resin and is subject to breakage.

To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out

by Authorized service center.

6. TECHNICAL DATA

Voltage/Frequency: 110-240 V ~ 50-60 HZ

Power: 900 W

Impact energy: 13 J

Impact rate: 2900 bpm

7. EXPLOSION VIEW AND SPARE PARTS LIST

INDEX

. MAIN PARTS DESCRIPTION .................................................................................................................. 2

2. GENERAL SAFETY RULES ..................................................................................................................... 3

3. ADDITIONAL SAFETY RULES ................................................................................................................ 5

4. OPERATION ............................................................................................................................................. 6

5. MAINTENANCE ....................................................................................................................................... 7

6. TECHNICAL DATA ................................................................................................................................... 8

7. EXPLOSION VIEW AND SPARE PARTS LIST ........................................................................................ 9

WARRANTY ............................................................................................................................................... 11