Daewoo DTE-29G3ZZR User manual

S/M No.:TCP795MEFO
Service Manual
ColorTelevision 68cm Stereo
CHASSIS : CP-795
Model : DTE-29G3ZZR
DTE-29G3KZR
Specirication
DAEWOO ELECTRONICS CO., LTD
http : //svc.dwe.co.kr March.2001
Items Model DTE-29G3ZZR/DTE-29G3KZR
TV Standard PAL-SECAM B/G D/K,PAL I/I,SECAM L/L
Sound System NICAM B/G,I,D/K,L,FM2Carrier B/G,D/K
Power Consumption 70W approx.
Sound Output Power 6W X 2(at60% mod,10%THD)
Speaker 12W 8 ohm X 2
Teletext System 10page memory FASTEXT(FLOF or top)
Aerial input 75ohm unbalanced
Channel coverage Off-air channels, S-cable channels and hyperband
Tuning System Frequency synthesiser tuning system
Visual screen size 68cm(DIAGONAL)
Channel indication On Screen Display
Program Selection 100programmes
Aux.terminal EURO-SCART1:Audio/Video In and Out,
R/G/B In, slow and fast switching.
EURO-SCART2:Audio/Video In and Out, S-VHS In.
Audio-Video jack on front of cabinet in common
connection with EURO-SCART2.
Headphone jack(3.5mm)on front of cabinet
Remote Control Unit R-40A13

TABLE OF CONTENTS
APPENDIX(Appendix is provide only by internet [http://svc.dwe.co.kr])
IC DESCRIPTION ............................................................................................................1
TDA936X TV SIGNAL PROCESSOR-TELETEXT DECODER WITH EMBEDDED U-CONTROLLER...................... 1
MSP3415D MULTISTANDARD SOUND PROCESSOR.............................................................................................. 9
TDA894XJ STEREO AUDIO AMPLIFIER.................................................................................................................... 13
TDA835XJ VERTICAL AMPLIFIER.............................................................................................................................. 14
TDA6107Q.................................................................................................................................................................... 17
24C16 16Kbit EEPROM ............................................................................................................................................... 18
STR-F6653 ................................................................................................................................................................... 19
CIRCUIT DISCRIPTION................................................................................................... 21
BLOCK DIAGRAM........................................................................................................................................................ 21
IF................................................................................................................................................................................... 25
SOURCE SWITCHING................................................................................................................................................. 27
U-CONTROLLER I/O PIN CONFIGURATION AND FUNCTION.................................................................................27
SOUND PROCESSING................................................................................................................................................ 28
SOUND AMPLIFICATION ............................................................................................................................................ 31
VERTICAL DEFLECTION ............................................................................................................................................ 31
POWER SUPPLY ......................................................................................................................................................... 33
TV START-UP, TV NORMAL RUN AND STAND-BY MODE OPERATIONS .............................................................. 37
MAIN FEATURES ....................................................................................................................... 2
SPECIFICATIONS ........................................................................................................................................................ 2
CHANNEL TABLE ........................................................................................................................................................ 4
SAFETY INSTRUCTION.................................................................................................. 9
CIRCUIT BLOCK DIAGRAM ........................................................................................... 10
ALIGNMENT INSTRUCTIONS ........................................................................................ 11
MICROCONTROLLER CONFIGURATION:SERVICE MODE .....................................................................................11
MICROCONTROLLER CONFIGURATION:OPTION...................................................................................................11
TV SET ALIGNMENT ................................................................................................................................................... 11
SCHEMATIC DIAGRAM ..................................................................................................14
EXPLODED VIEW...........................................................................................................15
PRINTED CIRCUIT BOARD ............................................................................................16
ELECTRICAL PARTS LIST .............................................................................................17
-1-

Service manual CP-795
- 2 -
TV standard PAL - SECAM B/G D/K, PAL I/I, SECAM L/L’
Sound system NICAM B/G, I, D/K, L,
FM 2Carrier B/G, D/K
Power consumption 70W approx.
Sound Output Power 6Wx 2 (at 60% mod, 10%THD)
Speaker 12W 8 ohm x2
Teletext system 10 pages memory FASTEXT (FLOF orTOP)
Aerial input 75 ohm unbalanced
Channel coverage Off-air channels, S-cable channels and hyperband
Tuning system Frequency synthesiser tuning system
Visual screen size 68cm (DIAGONAL)
Channel indication On Screen Display
Program Selection 100 programmes
Aux. terminal EURO-SCART 1 :Audio /Video In and Out, R/G/B In, Slow and
Fast switching.
EURO-SCART 2 :Audio /Video In and Out, S-VHS In.
Audio-Video Jack on front of cabinet in common connection with
EURO-SCART 2.
Headphone jack (3.5 mm) on front of cabinet
Remote Control Unit R-40A13
1-Main features
1-1 Specifications
21 Pin EURO-SCART 1:
Pin Signal Description Matching value
1 Audio Output Right 0.5 Vrms, Impedance < 1 , ( RF 54% Mod )
2 Audio Input Right 0.5Vrms, Impedance > 10
3 AudioOutputLeft 0.5Vrms, Impedance < 1 , ( RF 54% Mod )
4 Audio Earth
5 Blue Earth
6 Audio Input Left 0.5Vrms, Impedance > 10
7 Blue Input 0.7Vpp ±0.1V, Impedance 75
8 Slow Switching TV : 0 to 2V,AV 16/9 : 4.5 to 7V,AV Auto : 9.5 to 12V ,
Impedance > 10
9Green Earth
10 N.C.
11 Green Input 0.7Vpp ± 0.1V, Impedance 75
12 N.C.
13 Red Earth
14 Blanking Earth
15 Red Input 0.7Vpp ± 0.1V, Impedance 75
16 Fast Switching 0 to 0.4V : Logic “0”, 1 to 3V : Logic “1”, Impedance 75
17 Video Out Earth
18 Video In Earth
19 Video Output 1Vpp ± 3dB, Impedance 75

Service manual CP-795
- 3 -
20 Video Input 1Vpp ± 3dB, Impedance 75
21 Common Earth
21 Pin EURO-SCART 2:
Pin Signal Description Matching value
1 Audio Output Right 0.5Vrms, Impedance < 1 , ( RF 54% Mod )
2 Audio Input Right 0.5Vrms, Impedance > 10
3 Audio Output Left 0.5 Vrms, Impedance < 1 , ( RF 54% Mod )
4AudioEarth
5Earth
6 Audio Input Left 0.5Vrms, Impedance > 10
7N.C.
8N.C.
9N.C.
10 N.C.
11 N.C.
12 N.C.
13 Earth
14 Earth
15 Chroma Input ± 3dB for a luminance signal of 1Vpp
16 N.C.
17 Video Out Earth
18 Video In Earth
19 VideoOutput 1Vpp ± 3dB, Impedance 75
20 Video Input,Y In. 1 Vpp ± 3dB, Impedance 75
21 Common Earth

Service manual CP-795
- 4 -
1-2 Channel table
FREQUENCY TABLE
CH EUROPE CCIR FRANCE GB(IRELAND) EAST OIRT
C01 46.25 - 45.75 49.75
C02 48.25 55.75 (L’) 53.75 59.25
C03 55.25 60.5 (L’) 61.75 77.25
C04 62.25 63.75 (L’) 175.25 85.25
C05 175.25 176.00 183.25 93.25
C06 182.25 184.00 191.25 175.25
C07 189.25 192.00 199.25 183.25
C08 196.25 200.00 207.25 191.25
C09 203.25 208.00 215.25 199.25
C10 210.25 216.00 223.25 207.25
C11 217.25 189.25 (LUX) 231.25 215.25
C12 224.25 69.25 (L’) 239.25 223.25
C13 53.75 76.25 (L’) 247.25 -
C14 - 83.25 (L’) 49.75 -
C15 82.25 90.25 57.75 -
C16 - 97.25 65.75 -
C17 183.75 - 77.75 -
C18 192.25 - 85.75 -
C19 201.25 - - -
C20 ----
C21 471.25 471.25 471.25 471.25
C22 479.25 479.25 479.25 479.25
C23 487.25 487.25 487.25 487.25
C24 495.25 495.25 495.25 495.25
C25 503.25 503.25 503.25 503.25
C26 511.25 511.25 511.25 511.25
C27 519.25 519.25 519.25 519.25
C28 527.25 527.25 527.25 527.25
C29 535.25 535.25 535.25 535.25
C30 543.25 543.25 543.25 543.25
C31 551.25 551.25 551.25 551.25
C32 559.25 559.25 559.25 559.25
C33 567.25 567.25 567.25 567.25
C34 575.25 575.25 575.25 575.25
C35 583.25 583.25 583.25 583.25
C36 91.25 591.25 591.25 591.25
C37 599.25 599.25 599.25 599.25
C38 607.25 607.25 607.25 607.25
C39 615.25 615.25 615.25 615.25
C40 623.25 623.25 623.25 623.25
C41 631.25 631.25 631.25 631.25
C42 639.25 639.25 639.25 639.25
C43 647.25 647.25 647.25 647.25
C44 655.25 655.25 655.25 655.25
C45 663.25 663.25 663.25 663.25

Service manual CP-795
- 5 -
C46 671.25 671.25 671.25 671.25
C47 679.25 679.25 679.25 679.25
C48 687.25 687.25 687.25 687.25
C49 695.25 695.25 695.25 695.25
C50 703.25 703.25 703.25 703.25
C51 711.25 711.25 711.25 711.25
C52 719.25 719.25 719.25 719.25
C53 727.25 727.25 727.25 727.25
C54 735.25 735.25 735.25 735.25
C55 743.25 743.25 743.25 743.25
C56 751.25 751.25 751.25 751.25
C57 759.25 759.25 759.25 759.25
C58 767.25 767.25 767.25 767.25
C59 775.25 775.25 775.25 775.25
C60 783.25 783.25 783.25 783.25
C61 791.25 791.25 791.25 791.25
C62 799.25 799.25 799.25 799.25
C63 807.25 807.25 807.25 807.25
C64 815.25 815.25 815.25 815.25
C65 823.25 823.25 823.25 823.25
C66 831.25 831.25 831.25 831.25
C67 839.25 839.25 839.25 839.25
C68 847.25 847.25 847.25 847.25
C69 855.25 855.25 855.25 855.25
C70 863.25 863.25 863.25 863.25
C71 69.25 - - -
C72 76.25 - - -
C73 83.25 - - -
C74 90.25 - - -
C75 97.25 - - -
C76 59.25 - - -
C77 93.25 - - -
S01 105.25 104.75 103.25 105.25
S02 112.25 116.75 111.25 112.25
S03 119.25 128.75 119.25 119.25
S04 126.25 140.75 127.25 126.25
S05 133.25 152.75 135.25 133.25
S06 140.25 164.75 143.25 140.25
S07 147.25 176.75 151.25 147.25
S08 154.25 188.75 159.25 154.25
S09 161.25 200.75 167.25 161.25
S10 168.25 212.75 - 168.25
S11 231.25 224.75 - 231.25
S12 238.25 236.75 - 238.25
S13 245.25 248.75 255.25 245.25
S14 252.25 260.75 263.25 252.25
S15 259.25 272.75 271.25 259.25
S16 266.25 284.75 279.25 266.25
S17 273.25 296.75 287.25 273.25

Service manual CP-795
- 6 -
S18 280.25 136.00 295.25 280.25
S19 287.25 160.00 303.25 287.25
S20 294.25 - - 294.25
S21 303.25 303.25 - 303.25
S22 311.25 311.25 311.25 311.25
S23 319.25 319.25 319.25 319.25
S24 327.25 327.25 327.25 327.25
S25 335.25 335.25 335.25 335.25
S26 343.25 343.25 343.25 343.25
S27 351.25 351.25 351.25 351.25
S28 359.25 359.25 359.25 359.25
S29 367.25 367.25 367.25 367.25
S30 375.25 375.25 375.25 375.25
S31 383.25 383.25 383.25 383.25
S32 391.25 391.25 391.25 391.25
S33 399.25 399.25 399.25 399.25
S34 407.25 407.25 407.25 407.25
S35 415.25 415.25 415.25 415.25
S36 423.25 423.25 423.25 423.25
S37 431.25 431.25 431.25 431.25
S38 439.25 439.25 439.25 439.25
S39 447.25 447.25 447.25 447.25
S40 455.25 455.25 455.25 455.25
S41 463.25 463.25 463.25 463.25

Service manual CP-795
- 7 -
1-3ATSS sorting method
The TV set sweeps all theTV bands from beginning ofVHF to end of UHF. TheTV controlling software
for each program checks if aVPS CNI code is transmitted. If noVPS CNI code is found, the system check
if a CNI code is transmitted in the teletext lines ( Packet 8/30 format 1 ). If such a code (VPS or teletext )
is found and if this code is in theATSS list, the program is automatically named.
The programs found are then sorted in 4 groups :
Group I : It contains all the programs from the selected country and named by the TV controlling
software.Within this group the sorting order is fixed by theATSS list.
Group II : It contains all the programs with a strong signal strength which are not listed in group I.
Group III : It contains all the programs with a weak signal strength which are not listed in group I.
Group IV : If two or more programs with the same code are found, only the strongest ( or if they have the
same level the one with the lowest frequency) is listed in group I, II or III. The others are listed in group
IV.
Note : If two programs with the same name but a different code are found these two programs are listed in
group I, II or III ( e.g. Regional program SW3 in Germany ).
The sorting order within group II, III, and IV is based on the channel frequency. The program with the
lowest frequency is allocated the first rank in its group, and so forth until the last program of the group
which has the highest frequency.
Program Group Skip
number
1
... Group II
m
m+1
... Group III
p
p+1
... Group IV
q
q+1
... not used
99
0
Special case : Country selection = Others
➼
Program Group Skip
number
1
2 Group I
...
n
n+1
... GroupII
m
m+1
... Group III
p
p+1
... Group IV
q
q+1
.... not used
99
0
➼

Service manual CP-795
- 8 -
Special case : France
If France is selected the TV controlling software sweeps the whole TV bands firstly with France system
selected ( positive video modulation) and secondly with Europe system selected ( negative video
modulation).
Special case : Switzerland
If Switzerland is selected the TV controlling software sweeps the whole TV bands firstly with Europe
system selected (negative video modulation) and secondly with France system selected ( positive video
modulation).
Special case : GB
Note for satellite receiver users : Before startingATSS turn On your satellite receiver and tune “SKY
NEWS “.
If GB is selected the TV controlling software seeks for programs only in UHF ( C21 to C70 ). The sorting
order is :
1 - BBC1
2 - BBC2
3 - ITV
4 - CH4
5 - CH5
6 - NEWS
If two or more “identical “programs ( same name but different code e.g. BBC1 and BBC1 Scotland ) are
found the following programs in the list will be shifted up. (1 - BBC1, 2 - BBC1, 3 - BBC2, 4 - ITV, 5 -
CH4, 6 - CH5, 7 - NEWS, ..)
If one of the program above is not found, the associated program number remains empty ( freq.=467.25
Mhz - Skip selected - no name - system=GB).
exampleA : 1 - BBC1, 2 - BBC2, 3 - ITV, 4 - ——, 5 - CH5, 6 - NEWS, ...
example B ( if 2 BBC1 found ) : 1 - BBC1, 2 - BBC1, 3 - BBC2, 4 - ITV, 5 - ——, 6 - CH5, 7 - NEWS, ...

Service manual CP-795
- 9 -
2 - Safety instruction
WARNING: Only competent service personnel may carry out work involving the testing or repair of this
equipment.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such
hazards, the high voltage must not exceed the specified limit.The nominal value of the high voltage of
this receiver is 28 KV at max beam current.The high voltage must not, under any circumstances, exceed
30KV. Each time a receiver requires servicing, the high voltage should be checked. It is important to use
an accurate and reliable high voltage meter.
2. The only source of X-RAY Radiation in this TV receiver is the picture tube. For continued X-RAY
RADIATION protection, the replacement tube must be exactly the same type tube as specified in the parts
list.
SAFETY PRECAUTION
1. Potentials of high voltage are present when this receiver is operating. Operation of the receiver
outside the cabinet or with the back board removed involves a shock hazard from the receiver.
1) Servicing should not be attempted by anyone who is not thoroughly familiar with the
precautions necessary when working on high voltage equipment.
2) Discharge the high potential of the picture tube before handling the tube. The picture tube is
highly evacuated and if broken, glass fragments will be violently expelled.
2. If any Fuse in this TV receiver is blown, replace it with the FUSE specified in the Replacement Parts
List.
3. When replacing a high wattage resistor (oxide metal film resistor) in circuit board, keep the resistor
10 mm away from circuit board.
4. Keep wires away from high voltage or high temperature components.
5. This receiver must operate underAC 230 volts, 5O Hz. NEVER connect to DC supply or any other
power or frequency.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this equipment have special safety-related characteristics.These
characteristics are often passed unnoticed by a visual inspection and the X-RAY RADIATION protection
afforded by them cannot necessarily be obtained by using replacement components rated for higher
voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in
this manual and its supplements, electrical components having such features are identified by designated
symbol on the parts list. Before replacing any of these components, read the parts list in this manual
carefully. The use of substitutes replacement parts which do not have the same safety characteristics as
specified in the parts list may create X-RAY Radiation.

Service manual CP-795
- 10 -

Service manual CP-795
- 11 -
4 - Alignment instructions
4-1 Microcontroller configuration : Service mode
To switch the TV set into service mode please sees instruction below.
1 - Select pr. number 91
2 -Adjust sharpness to minimum and exit all menu.
3 - Quickly press the key sequence : RED - GREEN - menu
To exit SERVICE menu press menu key or Std By key.
In Service Mode press “OK”to stop the microcontroller i.e. the I2C bus is free and the set can be
controlled by external equipment. Press “OK”again to allow the microcontroller to control the set again
4-2 Microcontroller configuration : Option
4-3-2 -White balance
- Select a dark picture and adjust Black G and Black R to the desired colour
temperature.
- Select a bright picture and adjustWP Red, WP Green, WP Blue to the desired
colour temperature.
4-3-3 - Focus
-Adjust the Focus volume ( on FBT ) to have the best resolution on screen.
Option Tuner maker
0 DAEWOO/SAMSUNG
1 DAEWOO/SAMSUNG
2 SIEL
3 PHILIPS
4-3 TV setAlignment
4-3-1 - G2 alignment
- TV inAV mode without video signal ÞBlack screen.
- TV preset withWP Red, WP Green andWP Blue equal to 32.
- TV preset with Black R, Black G equal to 8.
- Set TV in NORMAL I mode
-Adjust screen volume ( on FBT ) such that the highest cathode cut-off voltage measured on CRT board,
is Vcut off ± 5V.
Screen size Vcut-off
29”142V

Service manual CP-795
- 12 -
4-3-4 -Vertical geometry
-Adjust theVerticalAmplitude, Shift, S-
Correction and Slope to compensate for vertical
distortion.
4-3-5 - Horizontal picture centering
- Adjust H Shift to have the picture in the center of the screen.
4-3-6 - East / West correction
- Adjust the H Parall, H Bow, H Width, EW Parabo, Up Corner, Dw Corner, EW trapez to compensate for
geometrical distortion.
H. Parall
EW.Parabo
H. Bow
Up Corner
H.Width
Dw Corner

Service manual CP-795
- 13 -
EW Trapez
4-3-7 -AGC
-Adjust the antenna signal level at 68 dB V± 2
- Set RFAGC to 0.
- Increase RFAGC level and stop when the level on pin 6 of TDA936x goes below 2.5Vdc

- 14 -
SCHEMATIC DIAGRAM

- 15 -
1. DTE-29G3ZZR/29G3KZR
EXPLODEDVIEW

- 16 -
PCB MAIN
PRINTED CIRCUIT BOARD

- 17 -
LOC PART CODE PART NAME PART DESCRIPTION REMARK
ZZ100 48B3740A01 TRANSMITTER REMOCON R-40A01 ®
ZZ110 PTACPWD395 ACCESSORY AS DWP-28W2ZZF
00010 4850Q00910 BATTERY R03/NN
M821 4858213800 BAG INSTRUCTION L.D.P.E T0.05X250X400
ZZ120 PTBCSHD416 COVER BACK AS DTE-29G3ZZR
M211 4852150261 COVER BACK HIPS BK
M211D 4857817630 CLOTH BLACK FELT 400X20X0.7
M211E 4857817612 CLOTH BLACK FELT 250X20X0.7
M541 4855415800 SPEC PLATE 150ART P/E FILM (C/TV)
ZZ130 PTPKCPD416 PACKING AS DTE-29G3ZZR
M681 4856812400 BAND PP AUTO 0.95X17mmX1000m
M801 48580531QK BOX CARTON DW-4S
M811 4858185100 PAD EPS 29G3
M822 4858215600 BAG P.E PE FOAM t0.5x1600x1270
ZZ131 48519A4210 CRT GROUND NET 2901H-1015-2P
ZZ132 58G0000145 COIL DEGAUSSING DC-29S2
ZZ140 PTCACAD416 CABINET AS DTE-29G3ZZR
M201A 4856215402 WASHER RUBBER CRT2.0
M201B 4856015820 SCREW CRT FIX SWRM+SK5 L=35
M211A 7172401612 SCREWTAPPTITE TT2TRS 4X16 MFZN BK
M211B 7178301212 SCREWTAPPTITE TT2WAS 3X12 MFZN BK
M211C 7172401612 SCREWTAPPTITE TT2TRS 4X16 MFZN BK
M231 4852324303 PANEL L ABS GY
M231A 7178301212 SCREWTAPPTITE TT2WAS 3X12 MFZN BK
M232 4852324403 PANEL R ABS GY
M281 4852821103 DOOR ABS GY
M352 97P4602700 CLAMP CORD NYLON 66 BLK 5280N
M381A 7178301212 SCREWTAPPTITE TT2WAS 3X12 MFZN BK
M481 4854853203 BUTTON POWER ABS GY
M481A 4856716000 SPRING SWPA PIE0.5
M501 4855058400 DECO CTRL PVCT0.25
M551 4855534901 DECO SENSOR PMMA CL
M551A 7178301011 SCREWTAPPTITE TT2WAS 3X10 MFZN
M561 48556174SD MARK BRAND SILVER DIA-CUTTING
M681 4856812001 TIE CABLE NYLON66 DA100
M682 4856816300 CLAMPWIRE NYLON 6 (V0)
M791 4857923300 DOOR LOCK LA701(KIFCO)
P405 4850706S15 CONNECTOR B406-06P+YFH800+USW=500
SP01A 7172401612 SCREWTAPPTITE TT2TRS 4X16 MFZN BK
SP02A 7172401612 SCREWTAPPTITE TT2TRS 4X16 MFZN BK
V901 4859634160 CRT A68AGA25X105 ®
ZZ200 PTFMSJD416 MASK FRONT AS DTE-29G3ZZR
M201 4852066013 MASK FRONT HIPS GY
ZZ202 PTCTMSD416 PCB CONTROL MANUAL A DTE-29G3ZZR
10 2193100710 SOLDER POWER BAR S62S-PB37-SB1
20 2193011101 SOLDERWIRE RS 60-1.2 1.6A
30 2291050615 FLUX SOLDER DF-2012U
40 2291050301 FLUX SOLVENT IM-1000
90 2291051001 FLUX KILLER KFT-7
DF01 DSD50RH51B LED SD50-RH51BGRW
DF01A 4853533600 HOLDER LED P.P BK
HPF01 4859102130 JACK EARPHONE YSC-1537 ®
IF01 1TS0P1238W IC PREAMP TS0P1238WI1
JPF01 4859108450 JACK PIN BOARD YSC03P-4120-14A
M381 4853816400 FRAME SUB PCB FR HIPS BK
P603A 4850706S01 CONNECTOR YH025-06+YST025+ULW=200
P701A 4850703S18 CONNECTOR YH025-03+YST025+ULW=200
P703A 4850705S02 CONNECTOR YH025-05+YST025+ULW=200
P704A 4850706S01 CONNECTOR YH025-06+YST025+ULW=200
P803A 4850702S09 CONNECTOR BL102NG+MXH40058-02=300
SWF01 5S40101143 SW POWER PUSH PS3-22SP (P.C.B)
ZZ200 PTCTJRD416 PCB CONTROL RADIAL AS DTE-29G3ZZR
SW02 5S50101090 SWTACT THVH472GCA
SW03 5S50101090 SWTACT THVH472GCA
SW04 5S50101090 SWTACT THVH472GCA
SW05 5S50101090 SWTACT THVH472GCA
SW06 5S50101090 SWTACT THVH472GCA
ZF01 5PXF1B471M FILTER EMI CFI 06 B 1H 470PF
ZF02 5PXF1B471M FILTER EMI CFI 06 B 1H 470PF
ZZ200 PTCTJAD416 PCB CONTROL AXIAL AS DTE-29G3ZZR
A001 4859833114 PCB CONTROL 246X56(246X246/1X4) S1B
DF02 DUZ5R6BM-- DIODE ZENER UZ-5.6BM
DF03 DUZ5R6BM-- DIODE ZENER UZ-5.6BM
DF04 DUZ5R6BM-- DIODE ZENER UZ-5.6BM
RF02 RD-4Z181J- R CARBON FILM 1/4 180 OHM J
RF03 RD-4Z221J- R CARBON FILM 1/4 220 OHM J
RF04 RD-AZ331J- R CARBON FILM 1/6 330 OHM J
RF05 RD-4Z471J- R CARBON FILM 1/4 470 OHM J
RF06 RD-4Z471J- R CARBON FILM 1/4 470 OHM J
RF07 RD-4Z471J- R CARBON FILM 1/4 470 OHM J
ZZ220 PTSPPWD395 SPEAKER AS DWP-28W2ZZF ®
P601A 4850704S30 CONNECTOR YH025-04+35098+ULW=700
SP01 4858314810 SPEAKER SP-80F02 10W 8 OHM
SP02 4858314810 SPEAKER SP-80F02 10W 8 OHM
ZZ290 PTMPMSD416 PCB MAIN MANUAL AS DTE-29G3ZZR ®
C402 CMYH3C562J C MYLAR 1.6KV BUP 5600PF J
C404 CMYH3C702J C MYLAR 1.6KV BUP 7000PF J
C408 CMYE2G394J C MYLAR 400V PU 0.39MF J
C499 CEYD1H689W C ELECTRO 50V RHD 6.8MF (16X35.5)
C801 CL1JB3474K C LINE ACROSS AC250V 0.47MF U/C/SNDF/SV
C805 CEYN2G181P C ELECTRO 400V LHS 180MF (25X35)
C812 CH1AFE472M C CERA AC 4KV 4700PF M KX DE1610
C813 CEXF2E101V C ELECTRO 250V RSS 100MF 18X35.5
D403 DDG3------ DIODE DG3
LOC PART CODE PART NAME PART DESCRIPTION REMARK
SERVICE PARTS LIST
CAUTION
“ ” IS RECOMMENDABLE PART FOR STOCK.
“ ® ” IS SAFETY COMPONEMT, SO IT MUST BE USED EHE SAME COMPONENT

ELECTRICAL PARTS LIST
- 18 -
D404 DRGP30J--- DIODE RGP30J
D820 DRGP30J--- DIODE RGP30J
D860 DRGP30J--- DIODE RGP30J
F801 5FSCB4022R FUSE CERA SEMKO F4AH 4A 250V MF51
G900 4SG0D00103 SPARK GAP S-23 900V-1.5KV
G901 4SG0D00103 SPARK GAP S-23 900V-1.5KV
G902 4SG0D00103 SPARK GAP S-23 900V-1.5KV
G903 4SG0D00103 SPARK GAP S-23 900V-1.5KV
I301 PTA2SW8214 HEAT SINK ASS`Y 1TDA8358J- + 7174301011
00001 1TDA8358J- ICVERTICAL TDA8358J ®
0000A 4857028214 HEAT SINK AL EX
0000B 7174301011 SCREWTAPPTITE TT2 RND 3X10 MFZN
I501 1DW3653BE3 IC MICOM DW9365/N1/3-BE3
I601 1MSP3415D- IC AUDIO MSP3415D ®
I602 PTA2SW8217 HEAT SINK ASS`Y 1TDA8946J- + 7174301011
00001 1TDA8946J- IC AUDIO TDA8946J
0000A 4857028217 HEAT SINK AL EX
0000B 7174301011 SCREWTAPPTITE TT2 RND 3X10 MFZN
I702 1AT24C08PC IC AT24C08-10PC ®
I801 PTC2SW7910 HEAT SINK ASS`Y 1STRF6653- + 7174300811
00001 1STRF6653- IC SMPS STR-F6653 ®
0000A 4857027910 HEAT SINK AL EX
0000B 7174300811 SCREWTAPPTITE TT2 RND 3X8 MFZN
I804 1KP1010C-- IC PHOTO COUPLER KP-1010C
I806 1SE130N--- IC SE130N ®
810 TX0202DA-- THYRISTOR X0202DA1BA2
I820 1K1A7805P1 IC REGULATOR KIA7805API
I822 1K1A7808P1 IC REGULATOR KIA7808API
I823 1LP295033- IC REGULATOR LP2950 3.3V
I901 PTC3SW1100 HEAT SINK ASS`Y 1TDA6107Q- + 7174300811
00001 1TDA6107Q- ICVIDEO TDA6107Q ®
0000A 4857031100 HEAT SINK A1050P-H24T2.0
0000B 7174300811 SCREWTAPPTITE TT2 RND 3X8 MFZN
JPA1 4859200401 SOCKET RGB YRS21-R1
JPA2 4859200401 SOCKET RGB YRS21-R1
L401 58H0000066 COIL H-LINEARITY TRL-230D
L402 58C0000122 COIL CHOKE CH-401B
L802 58C9430599 COIL CHOKE AZ-9004Y(94MH)
LF801 5PLF24A1-- FILTER LINE LF-24A1
M951B 4853535500 HOLDER CORD NYROLN 66
P401 4850705N14 CONNECTOR BIC-05T-25T+ULW=500
P402 4859240120 CONNWAFER YFW500-06
P501 4850705N14 CONNECTOR BIC-05T-25T+ULW=500
P601A 4850704S30 CONNECTOR YH025-04+35098+ULW=700
P801 4859242220 CONNWAFER YFW800-02
P802 4859242220 CONNWAFER YFW800-02
P803 4859242220 CONNWAFER YFW800-02
P903 4859238620 CONNWAFER YPW500-02
PWC1 PTWBSW7410 CORD POWER ASS`Y 906111+HOUSING+TUBE+17700
PW000 4859906111 CORD POWER M5206+H03VVH2-F=2250
PW001 4857417700 TERM CLAMP PT-01-T3
Q401 PTS2SW4500 HEAT SINK ASS`Y T2SW2499-- + 7174300811 ®
Q401 T2SD2499-- TR 2SD2499
Q401A 4857024500 HEAT SINK AL EX B/K
Q401B 7174300811 SCREWTAPPTITE TT2 RND 3X8 MFZN
R801 DPC7R0M290 POSISTOR 2322 662 96709
R802 RS02Y753JS R M-OXIDE FILM 2W 75K OHM J SMALL
R819 RX10B339JQ R CEMENT 10W 3.3 OHM J BEN 25MM 4P ®
R920 RF01Y209JA R FUSIBLE 1W 2 OHM J A CURVE
SCT1 4859303530 SOCKET CRT PCS629-03C
SF1 5PK3953M-- FILTER SAW K3953M
SF2 5PK9650M-- FILTER SAW K9650M
T401 50D19A1--- TRANS DRIVE TD-19A1
T402 50H0000216 FBT 1352.5052 ®
T801 50M4936B1- TRANS SMPS 2094.0041
U100 4859719930 TUNERVARACTOR DT5-BF18D ®
X502 5XE12R000E CRYSTAL QUARTZ HC-49/U 12.00000MHZ 30PPM
X601 5XE18R432E CRYSTAL QUARTZ HC-49/U 18.43200MHZ 30PPM
Z501 5PYXT5R5MB FILTER CERA XT 5.5MB
ZZ200 PTMPJ0D416 PCB MAIN (RHU) AS DTE-29G3ZZR
C305 CEXF1E471V C ELECTRO 25V RSS 470MF (10X16)TP
C315 CEXF2C470C C ELECTRO 160V RUS 47MF (13X25)TP
C415 CEXF2E479V C ELECTRO 250V RSS 4.7MF (10X16)TP
C430 CCXB3D681K C CERA 2KV B 680PF K (TAPPING)
C431 CMXB2G472J C MYLAR 400V EU 4700PF J (TP)
C440 CMXE2G273J C MYLAR 400V PU 0.027MF J (TP)
C511 CMXM2A224J C MYLAR 100V 0.22MF J
C512 CMXM2A224J C MYLAR 100V 0.22MF J
C604 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20)TP
C661 CMXM2A224J C MYLAR 100V 0.22MF J
C662 CMXM2A224J C MYLAR 100V 0.22MF J
C668 CMXM2A224J C MYLAR 100V 0.22MF J
C669 CMXM2A224J C MYLAR 100V 0.22MF J
C810 CBXB3D102K C CERA SEMI 2KV BL(N) 1000PF K (T)
C814 CEXF2E470V C ELECTRO 250V RSS 47MF (16X25)TP
C823 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20)TP
C832 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20)TP
C840 CEXF1C222V CELECTRO 16V RSS 2200MF (13X25)TP
C841 CEXF1C222V CELECTRO 16V RSS 2200MF (13X25)TP
C861 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20)TP
C905 CEXF2E479V C ELECTRO 250V RSS 4.7MF (10X16)TP
C951 CEXF2E100V C ELECTRO 250V RSS 10MF (10X20)TP
C965 CCXB3D102K C CERA 2KV B 1000PF K (TAPPING)
ZZ200 PTMPJBD416 PCB MAIN M-10 AS DTE-29G3ZZR
LOC PART CODE PART NAME PART DESCRIPTION REMARK
LOC PART CODE PART NAME PART DESCRIPTION REMARK

ELECTRICAL PARTS LIST
- 19 -
10 2TM18006BE TAPE MASKING 6.2X500
P601 485923172S CONNWAFER YW025-04 (STICK)
P603 485923202S CONNWAFER YW025-07 (STICK)
701 485923162S CONNWAFER YW025-03 (STICK)
P703 485923182S CONNWAFER YW025-05 (STICK)
P704 485923192S CONNWAFER YW025-06 (STICK)
R331 RS01Z201J- R M-OXIDE FILM 1W 200 OHM J (TAPPING)
R398 RF01Z828K- R FUSIBLE 1W 0.82 OHM K (TAPPING)
R399 RS02Z120JS R M-OXIDE FILM 2W 12 OHM J SMALL
R406 RS02Z471JS R M-OXIDE FILM 2W 470 OHM J SMALL
R803 RS02Z473JS R M-OXIDE FILM 2W 47K OHM J SMALL
R804 RF02Z158K- R FUSIBLE 2W 0.15 OHM K (TAPPING)
R806 RS01Z472J- R M-OXIDE FILM 1W 4.7K OHM J (TAPPING)
R808 RS02Z821JS R M-OXIDE FILM 2W 820 OHM J SMALL
ZZ200 PTMPJRD416 PCB MAIN RADIAL AS DTE-29G3ZZR
C101 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C102 CEXF1H470V C ELECTRO 50V RSS 47MF (6.3X11)TP
C106 CEXF1E221V C ELECTRO 25V RSS 220MF (8X11.5)TP
C120 CCXB1H102K C CERA 50V B 1000PF K (TAPPING)
C121 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C313 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C320 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C350 CCXF1H473Z C CERA 50V F 0.047MF Z (TAPPING)
C351 CCXF1H473Z C CERA 50V F 0.047MF Z (TAPPING)
C370 CMXM2A473J C MYLAR 100V 0.047MF J (TP)
C401 CEXF1H101V C ELECTRO 50V RSS 100MF (8X11.5)TP
C412 CEXF2C339V C ELECTRO 160V RSS 3.3MF (8X16)TP
C414 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C418 CCXB1H102K C CERA 50V B 1000PF K (TAPPING)
C420 CCXB2H222K C CERA 500V B 2200PF K (TAPPING)
C500 CEXF1H478V C ELECTRO 50V RSS 0.47MF (5X11)TP
C501 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C509 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11)TP
C514 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)TP
C517 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11)TP
C519 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11)TP
C524 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C525 CCXB1H102K C CERA 50V B 1000PF K (TAPPING)
C526 CMXL1J104J C MYLAR 63V MEU 0.1MF J
C527 CMXB2A473J C MYLAR 100V EU 0.047MF J (TP)
C528 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)TP
C530 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)TP
C531 CCXF1H473Z C CERA 50V F 0.047MF Z (TAPPING)
C532 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C537 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C540 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11)TP
C541 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11)TP
C542 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C543 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C550 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11)TP
C555 CEXF1C470V C ELECTRO 16V RSS 47MF (5X11)TP
C560 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C561 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)TP
C564 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)TP
C565 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C585 CCXB1H222K C CERA 50V B 2200PF K (TAPPING)
C590 CXCH1H270J C CERA 50V CH 27PF J (TAPPING)
C591 CXCH1H270J C CERA 50V CH 27PF J (TAPPING)
C592 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C593 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)TP
C601 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
C602 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C603 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
C605 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11)TP
C608 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C610 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C611 CEXF1H339V C ELECTRO 50V RSS 3.3MF (5X11)TP
C612 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11)TP
C613 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11)TP
C614 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11)TP
C615 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11)TP
C616 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C617 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C620 CXCH1H509D C CERA 50V CH 5PF D (TAPPING)
C621 CXCH1H509D C CERA 50V CH 5PF D (TAPPING)
C622 CCXF1H223Z C CERA 50V F 0.022MF Z (TAPPING)
C625 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11)TP
C626 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11)TP
C629 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C630 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11)TP
C631 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C635 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C636 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11)TP
C650 CXCH1H470J C CERA 50V CH 47PF J (TAPPING)
C660 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11)TP
C665 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
C666 CBXF1H104Z C CERA SEMI 50V F 0.1MF Z (TAPPING)
C667 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
C690 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11)TP
C691 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11)TP
C692 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11)TP
C698 CXCH1H470J C CERA 50V CH 47PF J (TAPPING)
C699 CXCH1H470J C CERA 50V CH 47PF J (TAPPING)
C770 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)TP
LOC PART CODE PART NAME PART DESCRIPTION REMARK
LOC PART CODE PART NAME PART DESCRIPTION REMARK