Daewoo RCU-3008 Series User manual

OWNER’S MANUAL
Contents
· Specification
· Components Description & Assembling
· Using Guide & Converting to Cylinder Mode
· Cleaning Dust Box & Replacement Filters
· Replacing Belt & Head Light
· Precautions for Safe Use
· Trouble Shooting
1
2
4
6
8
9
10
Read and Keep This
· Thank you for purchasing this vacuum cleaner.
· For proper operation, please read this manual
before use.
RCU-3008 Series / RCU-3006 Series
VACUUM CLEANER
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 1

1
DAEWOO Electronics
DUO VAC Upright Series
Specifications
Model
Rating
Watts
Weights (Net)
Dimension (LxWxH)
Cord Length
Inner Filter
Exhaust Filter
Head Light
Belt Agitator
RCU-3008 Series RCU-3006 Series
230 V / 50Hz
Max. 1800W Max. 1600W
9.3 Kg
1143 X 386 X 265 mm
10 m 7.2 m
HEPA Filter
Clean Filter
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 2

2
Cord Plug
Release
Pedal
**Thermal
Reset
Button
Hose Clip
Cord
Storage
Pipe
Extension
Button
Filter Indicator
(Red Lamp)
- If Dust Box is full or
Inlet Filter blocked,
Lamp will light.
Height
Setting
Control
Dust Box Handle
Removal
Button for
Head
Head Light
*Only Model
RCU-3008 Series
Main Power
Switch
Brush Power
Switch
HANDLE
(Grip+Pipe)
HOSE
BODY
DUST BOX
PEDAL BRUSH CREVICE NOZZLE DUSTING BRUSH BELT of AGITATOR BRUSH UPHOLSTERY NOZZLE
P
O
W
E
R
B
R
U
S
H
F
I
L
T
E
R
W
A
R
N
I
N
G
HEAD
CCOOMMPPOONNEENNTTSSDDEESSRRIIPPTTIIOONN&&AASSSSEEMMBBLLIINNGG
**Thermal Reset Button
Operates due to over heating, caused by full
Dust Box, clogged filter or blocked pipes.
Unplug the cleaner and Remove the blocked
materials. To operate again, after cooling down
the cleaner about 30 minutes, Press the
Thermal Reset Button.
Warning!
Do not use the Dust Box
Handle to move the Cleaner.
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 3

3
• HANDLE
assembling.
- Insert HANDLE in
the handle hole on
the top of the Body
as below the pic-
ture.
• HANDLE
disassembling.
- Push the Handle
Removal Button.
- Pull HANDLE
upward.
Protrusion
to lock
Handle
Removal
Button
HANDLE
• HEAD assembling.
- Set the CYLINDER on
the top of the HEAD as
below in the picture.
- Use the both sides of
the guide feature on
the HEAD.
• HEAD disassembling.
- Push the HEAD
Removal Button.
- Lift up the CYLINDER.
Removal
Button
for HEAD
HEAD
HOSE GUIDE & HOSE ASSEMBLING
HANDLE ASSEMBLING HEAD ASSEMBLING
• HOSE GUIDE assembling.
- Set HOSE GUIDE on the top of the cleaner.
- Screwing a screw with the "+" shape screw driver
• HOSE AS assembling.
- Insert the body end of HOSE AS in the hose hole
of the cleaner.
- Caution : Insert the protrusion of HOSE end
through "▲" mark in side of the hole
when connected the HOSE(body end)
and the BODY, The HOSE can not be
removed from the BODY. If you need
to disassemble it, call the A/S center.
HEAD
end
Body
end
HOSE
AS
Hose Guide
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 4

4
• Push the RELEASE PEDAL as below in the picture.
- Set HOSE GUIDE on the top of the cleaner.
- Caution : If the power switch is not ON, though the brush switch is ON,
The HEAD will not work.
If this cleaner is not working, though the power and the brush switches
are ON, the HEAD is not working because the safety device is operating.
(HEAD SAFETY SWITCH)
HEAD Safety
Switch
Release
Pedal
HEAD
• Disassemble the HEAD and the HANDLE. (See. Page 3)
• Disassemble the Head side of the HOSE AS and connect it with HANDLE as below.
• Assemble the PEDAL BRUSH to the pipe, and the PIPE to the HANDLE.
• Extend the PIPE with the Pipe Extension Button for convienient height.
Pipe Extension
Button
HEAD end
of HOSE
HANDLE HOSE AS
PEDAL BRUSH
USING IN UPRIGHT MODE
CONVERTING TO CYLINDER MODE
UUSSIINNGGGGUUIIDDEE&&CCOONNVVEERRTTIINNGGTTOOCCYYLLIINNDDEERRMMOODDEE
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 5

5
• Rotate the SUCTION CONTROL on the hose end as below.
Suction Control
• Rotate the HEIGHT SETTING KNOB to
the carpet height.
• To clean bare floor, this KNOB is set to
the position of BARE FLOOR and the
Brush Power Switch is turned OFF.
(on the top of the cleaner See-2page)
HEIGHT SETTING KNOB
SETTING
• After using the cleaner,
Store in UPRIGHT mode.
• The Accessories are located in the
storage holes in the BODY.
• Wrap the CABLE around the Cord
Storage hooks on the side of
BODY and hang the Plug
at the cord clip on the
HANDLE.
(side view)
Cord
Clip
Plug
Cord
Cable
SUCTION CONTROL
HEAD HEIGHT CONTROL KEEPING
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 6

6
• Turn OFF the Cleaner.
• Grasp the DUST BOX LEVER and
pull out the DUST BOX from BODY.
• Pull out the EXHAUST FILTER
- FULL - FULL
Dust
Removal
Button
• When dust reaches the "FULL" line in the DUST BOX or FILTER WARNING
LAMP light.
• To empty, Remove the DUST BOX.
• Push the DUST REMOVAL BUTTON and the dust will drop out.
CCLLEEAANNIINNGGDDUUSSTTBBOOXX&&RREEPPLLAACCEEMMEENNTTFFIILLTTEERRSS
DISASSEMBLING DUST BOX & EXHAUST FILTER
EMPTY DUST BOX
Dust Box
Lever
DUST BOX
EXHAUST
FILTER
BODY
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 7

7
Dust Box Cover
Inlet Filter
• Lift up the DUST BOX COVER and rotate and remove the INNER FILTER
• Tapping it to remove the dust from the pleats as below in the picture.
- Caution : This INNER FILTER is not washable. After tapping it, reassemble it and
use the cleaner. When tapping, be careful not to damage the filter.
Replace the new INNER FILTER in every a year.
CLEAN FILTER
Filter Frame Clean Filter
• Disassemble the EXHAUST FILTER. (See 6 page)
• If the EXHAUST FILTER become dirty. Replace it.
- Caution : This INNER FILTER is not washable.
INNER FILTER CLEANING AND REPLACING
EXHAUST FILTER CLEANING AND REPLACING
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 8

8
• Turn OFF the cleaner.
• Remove the BOTTOM PLATE of the HEAD. (unscrewing 5 screws with "+" shape
screw driver)
• Set the new BELT over Motor Pully.
• Slip the AGITATOR BRUSH into the BELT and reassemble.
• Replace the BOTTOM PLATE and secure the 5 screws.
- Warning : Before replacing the BELT. Check the cleaner is unplugged
from the electrical socket.
Head Light
Lense
• Turn OFF the cleaner.
• Press the RELEASE PEDAL and place the HANDLE in the low position.
• Remove the LENSE. (unscrewing a screw with "+" shape screw driver)
• Pull the BULB straight out of the SOCKET.
• Install the new BULB.
• Replace the LENSE and secure a screw.
RREEPPLLAACCIINNGGBBEELLTT&&HHEEAADDLLIIGGHHTT
REPLACING BELT OF AGITATOR BRUSH
REPLACING HEAD LIGHT ( ONLY FOR RCU-3008 SERIES )
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 9

9
This vacuum cleaner should only be used for normal dry household dust and dirt.
The manufacturer cannot be held responsible for any damage caused by use or operation of
the cleaner contrary to these instructions.
If the cleaner is wrongly operated for a purpose other than that for which it is intended, no
liability can be accepted for any possible damage.
P
O
W
D
E
R
• Do not vacuum areas which contain mois-
ture or water and inflammable matter, nee-
dles, pins, razor blades, matches, cigarette-
ends, etc., since they may damage the
cleaner or dust bag or cause a fire.
• When rewinding the power cord, hold the
plug body before pressing the cord rewind
button to prevent whipping.
• Do not pull the power cord out beyond the
specified length.
• Make sure the Filters always inserted. • This product provided with a cable which, if
damaged, must be replaced by a repair
shop authorized by the manufacturer since
special tools are required.
PPRREECCAAUUSSIIOONNSSFFOORRSSAAFFEEUUSSEE
RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 10