Dahua DH-IPC-HDBW4421EP-0280B User manual

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
1
Dahua HD IR Vandal Proof Network Dome Camera
Quick Start Guide
Version 1.0.1

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
i
Welcome
Thank you for purchasing our network camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Before your operation please read the following instructions carefully.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V or 24V AC DC in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
ii
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
Warranty Card and Certificate
1

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
iii
Table of Contents
1 Structure........................................................................................................................1
1.1 Components..................................................................................................................1
1.2 Framework and Dimension...............................................................................2
1.3 Alarm Setup......................................................................................................3
2 Device Installation .........................................................................................................5
2.1 Installation Steps...........................................................................................................5
2.2 Micro SD Card Installation ................................................................................7
3Quick Configuration Tool...............................................................................................8
3.1 Overview...........................................................................................................8
3.2 Operation..........................................................................................................8
4Web Operation ............................................................................................................10
4.1 Network Connection........................................................................................10
4.2 Login and Main Interface.................................................................................10
Appendix Toxic or Hazardous Materials or Elements ........................................................12

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
1
1Structure
1.1 Components
Note:
There are differences about wire structure for some product models, please refer to the actual object
for more details.
You can refer to the following figure for component structure. See Figure 1-1.
Figure 1-1 Component structure
Please refer to the following sheet for detailed information.
Component
Component Name
Component 1
Dome body
Component 2
Dome enclosure

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
2
Please refer to the following sheet for detailed information about I/O port.
Port
Name
Port
Sequence
Port name
Function Description
I/O Port
1
ALARM_IN1
Alarm input port, receive on-off signal of
external alarm source.
2
ALARM_OUT1
Alarm output port, output alarm signal to
alarm device.
3
ALARM_GND
Connect ground
1.2 Framework and Dimension
Please refer to the following two figures for dimension information. The unit is mm. See Figure 1-2
Figure 1-2
Port
Port Name
Note
Port 3
Power input port
Connect to DC 12V power, input power.
Port 4
I/O port
Alarm signal input/output (optional, supported by
some product models)
Port 5
Internet access port
Network data in/out and PoE.
Note:
Some devices do not support PoE.
Before making crystal head, pull the anti-dust,
waterproof cover through network cable.
Port 6
Audio input port
Input audio signal, receive analog audio signal from
sound pick-up.etc(optional, supported by some
product models)
Port 7
Audio output port
Output audio signal to speakers.etc (optional,
supported by some product models.)

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
3
1.3 Alarm Setup
Note:
Only supported by some series products.
Figure 1-3
Alarm input, output description:
Step 1 Connect alarm input device to the alarm input of I/O cable.
Step 2 Connect alarm output device to the alarm output of I/O cable, alarm output is collector open
circuit output which connects 10K resistor to 3.3V externally.
Step 3 Open the Web, set alarm input and output correspondingly. Alarm input on WEB
corresponds to I/O cable on device. When there is alarm, alarm input device will generate
signal of high and low level. Set corresponding NO and NC inputs.
Step 4 Set the WEB alarm output. The alarm output is for the alarm output port of the device. It is the
alarm output port of the I/O cable.
Please refer to the following figure for alarm input information. See Figure 1-4.
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of
the alarm input port. When the input signal is connected to 3.3V or idle, the device collects the logic “1”.
When the input signal is grounded, the device collects the logic “0”.
Figure 1-4

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
4
Please refer to the following figure for alarm output information. See Figure 1-5
Alarm output: Alarm output is OC door, requiring increase of external pull-up resistor. Output signal is
high and low levels. After pull-up resistor is increased, output signal is high level by default. When
there is alarm output, output signal becomes low level.
Figure 1-5

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
5
2Device Installation
2.1 Installation Steps
Important
Before the installation, please make sure the installation environments can at least support 3x
weight of the camera.
Please follow the steps listed below to install the device. Please refer to Figure 2-1 for reference.
Step 1
Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner hex
screws on enclosure.
Step 2
Please take the installation position map in the accessories bag, and then paste it on the ceiling or the
wall according to your monitor area requirements.
Step 3
Find cross signs on the map, and dig three plastic expansion bolts holes in the installation surface and
then insert three expansion bolts in the holes. Secure these three bolts firmly.
Note:
If use pulls out cable from top of installation surface, you must dig a exit hole on installation
surface according to the installation position map.
If user pulls out cable from side of cable channel, it must go through the U-shape channel on
dome pedestal, and take out cable from the side exit hole on pedestal.
Step 4
Adjust the device installation pedestal to the proper position and then pull cable through the exit hole
on Installation surface. Make direction of TOP sign same as it on installation position map. Line up the
three screw holes in the device pedestal to the three plastic expansion bolt holes in the installation
position. Put the three self-tapping screws in the three plastic expansion bolts firmly. Fix dome body on
installation surface.
Step 5
Hold bottom of bracket with hand, horizontally rotate bracket, adjusting lens direction to designated
position. Loosen one M2 screw on LED decoration cover (loosen only, do not take it down), hold the
decoration cover with hand, making lens rotate vertically. Adjust vertical direction of lens to appropriate
angle, and fasten the M2 screw. Range of lens: vertical (0°～+65°), horizontal (0°～+355°). See
Figure 2-2.

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
6
Figure 2-1 Device installation illustration 1
Figure 2-2 Device installation illustration 2

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
7
Note:
When you need to reset the device, press the “Reset”button in Figure 2-2 for 10 seconds while
connecting device to power.
When you need to use WPS function, press the “Reset”button in Figure 2-2 for 1 to 2 seconds while
connecting device to power, then press WPS button on the router. Generally the device can be
connected to corresponding router within 1 minute (supported by some series products).
Step 6
Take dome enclosure, put it back on the camera properly regarding to screw and hole, and fasten the
three inner hex screws with wrench.
2.2 Micro SD Card Installation
Note:
Some series products do not support the Micro SD card storage function. Please shut down the power
and then turn off the device before you install the Micro SD card.
Step 1 Find the Micro SD Card slot in figure 2-2, open the Micro SD Card slot according to the
direction in figure 2-3.
Step 2 Adjust the Micro SD Card to proper direction and install it in the Micro SD card slot.
Step 3 According to the direction in figure 2-4, close the Micro SD card slot and keep it locked.
Figure 2-3 Micro SD Card installation illustration 1
Figure 2-4 Micro SD Card installation illustration 2

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
8
3 Quick Configuration Tool
3.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
3.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface, in the device list interface, you can
view device IP address, port number, subnet mask, default gateway, MAC address and etc.
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 3-1.
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 3-1 Search interface
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface, please select a device IP address and then double click it to
open the login interface. Or you can select an IP address and then click the Login button to go to the
login interface. See Figure 3-2.
In Figure 3-2, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
9
Figure 3-2 Login prompt
After you logged in, the configuration tool main interface is shown as below. See Figure 3-3.
Figure 3-3 Main interface
For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
10
4 Web Operation
This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.
4.1 Network Connection
Please follow the steps listed below for network connection.
Make sure the network camera has connected to the network properly.
Please set the IP address, subnet mask and gateway of the PC and the network camera
respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1
Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.
4.2 Login and Main Interface
Open IE and input network camera address in the address bar. See Figure 4- 1.
Figure 4- 1 IP address
The login interface is shown as below. See Figure 4- 2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
11
Figure 4- 2 Web login
After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation
Manual included in the resource CD for detailed operation instruction.
See Figure 4- 3.
Figure 4- 3 Web monitoring window

Dahua HD IR Vandal Proof Network Dome Camera Quick Start Guide
12
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board
Component
○
○
○
○
○
○
Device Case
○
○
○
○
○
○
Wire and Cable
○
○
○
○
○
○
Packing
Components
○
○
○
○
○
○
Accessories
○
○
○
○
○
○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes.
Note:
This quick start guide is for reference only. Slight difference may be found in user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more information.

Dahua Technology Co., Ltd
Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: [phone]
Fax: [phone]
Email:[e-mail]
Website: www.dahuatech.com