Dahua F4X5 User manual

Dahua Network Speed Dome Web3.0 Operation Manual
i
Dahua Network Speed Dome Web3.0 Operation Manual
Version 1.0.0
Dahua Technology CO., LTD

Dahua Network Speed Dome Web3.0 Operation Manual
ii
Table of Contents
1Network Config............................................................................................................................1
1.1 Network Connection.....................................................................................................1
1.2 Log in ..............................................................................................................................1
2Live................................................................................................................................................5
2.1 Encode Setup................................................................................................................5
2.2 System Menu.................................................................................................................6
2.3 Video Window Function Option..................................................................................6
2.4 Video Window Setup....................................................................................................7
2.4.1 Image Adjustment.....................................................................................................7
2.4.2 Original Size.............................................................................................................8
2.4.3 Full Screen................................................................................................................8
2.4.4 Width and Height Ratio............................................................................................8
2.4.5 Fluency Adjustment..................................................................................................8
2.4.6 Rule Info...................................................................................................................8
2.4.7 PTZ...........................................................................................................................9
2.5 PTZ Configuration.........................................................................................................9
2.5.1 PTZ Control..............................................................................................................9
2.5.2 Virtual Joystick.........................................................................................................9
2.5.3 PTZ Function..........................................................................................................10
3Playback.....................................................................................................................................12
3.1 Playback.......................................................................................................................12
3.1.1 Function of Play......................................................................................................13
3.1.2 Playback File ..........................................................................................................13
3.1.3 Playback Cut (Clip) ................................................................................................16
3.1.4 Record Type ...........................................................................................................16
3.1.5 Progress Bar Time Format......................................................................................16
3.1.6 Assistant Function ..................................................................................................17
3.2 Picture Playback .........................................................................................................17
3.2.1 Play.........................................................................................................................18
3.2.2 Playback File ..........................................................................................................18
3.2.3 Snapshot Type ........................................................................................................19
4Setup...........................................................................................................................................20
4.1 Camera.........................................................................................................................20
4.1.1 Conditions...............................................................................................................20
4.1.2 Video ......................................................................................................................28
4.2 Network.........................................................................................................................34

Dahua Network Speed Dome Web3.0 Operation Manual
iii
4.2.1 TCP/IP ....................................................................................................................34
4.2.2 ONVIF....................................................................................................................36
4.2.3 Connection..............................................................................................................37
4.2.4 PPPoE.....................................................................................................................39
4.2.5 DDNS .....................................................................................................................40
4.2.6 IP filter....................................................................................................................42
4.2.7 SMTP （e-mail).....................................................................................................42
4.2.8 UPnP.......................................................................................................................44
4.2.9 SNMP .....................................................................................................................45
4.2.10 Bonjour...................................................................................................................47
4.2.11 Multicast.................................................................................................................48
4.2.12 802.1x .....................................................................................................................49
4.2.13 QoS.........................................................................................................................50
4.3 PTZ................................................................................................................................51
4.3.1 Function..................................................................................................................51
4.4 Event.............................................................................................................................62
4.4.1 Video detect............................................................................................................62
4.4.2 IVS Analysis...........................................................................................................66
4.4.3 Face Detect .............................................................................................................69
4.4.4 Abnormality............................................................................................................71
4.5 Storage Management.................................................................................................74
4.5.1 Schedule..................................................................................................................74
4.5.2 Destination..............................................................................................................78
4.5.3 Record control ........................................................................................................80
4.6 System..........................................................................................................................81
4.6.1 General....................................................................................................................81
4.6.2 Account...................................................................................................................83
4.6.3 Default ....................................................................................................................87
4.6.4 Import/Export .........................................................................................................88
4.6.5 Auto Maintenance...................................................................................................88
4.6.6 Upgrade ..................................................................................................................89
4.7 Information...................................................................................................................90
4.7.1 Version....................................................................................................................90
4.7.2 Log..........................................................................................................................90
4.7.3 Online User.............................................................................................................91
5Alarm...........................................................................................................................................92
6Log out........................................................................................................................................94

Dahua Network Speed Dome Web3.0 Operation Manual
iv
Important
The following functions are for reference only. Some series products may not
support all the functions listed below.

Dahua Network Speed Dome Web3.0 Operation Manual
1
1 Network Config
1.1 Network Connection
Speed dome and PC connection mainly has two ways. See Figure 1-1 and Figure 1-2.
Figure 1-1
Figure 1-2
Before you access speed dome via the Internet, you need to have its IP address. You can use quick
config tool to search IP of the speed dome. Please refer to Quick Configuration Tool manual.
1.2 Log in
Open IE and input speed dome address in the address bar.
For example, if your speed dome IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE
address bar. See Figure 1-3.

Dahua Network Speed Dome Web3.0 Operation Manual
2
Figure 1-3
The login interface is shown as below. See Figure 1-4.
Please input your user name and password.
Default factory username is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Figure 1-4
Input your IP
address here

Dahua Network Speed Dome Web3.0 Operation Manual
3
If it is your first time to login in, you may see the interface shown as in Figure 1-5.
Figure 1-5
Click “Please click here to download and install the plug-in”. The system pops up warning information to
ask you whether run or save this plug-in. Please download to your local computer and then click
webplugin.exe; you can see an interface shown as in Figure 1-6.

Dahua Network Speed Dome Web3.0 Operation Manual
4
Figure 1-6
Click install, you will see Figure 1-7.
Figure 1-7
When plug-in installation is complete, the installation page closes automatically. The web-end will
refresh automatically, and then you can view video captured by the camera.

Dahua Network Speed Dome Web3.0 Operation Manual
5
2 Live
After you logged in, you can see the live monitor window. See Figure 2-1.
Figure 2-1
There are four sections:
Section 1: Encode setup bar
Section 2: System menu
Section 3: Window function option bar
Section 4: Window adjust bar
2.1 Encode Setup
The encode setup interface is shown as in Figure 2-2.
2
1
3
4

Dahua Network Speed Dome Web3.0 Operation Manual
6
Figure 2-2
Please refer to the following sheet for detailed information.
Parameter
Function
Main stream
Streaming media protocol connection, under main stream config,
monitor video or not. Generally for storage and monitor.
Sub (Extra)
stream 1
Streaming media protocol connection, under sub stream 1
config, monitor video or not. When network bandwidth is
insufficient, it substitutes main stream for monitoring.
Sub (Extra)
stream 2
Streaming media protocol connection, under sub stream 2
config, monitor video or not. When network bandwidth is
insufficient, it substitutes main stream for monitoring.
Protocol
You can select stream media protocol from the dropdown list.
There are three options: TCP/UDP/Multicast
2.2 System Menu
System menu is shown as in Figure 2-3.
Please refer to chapter 2 Live, chapter 3 Playback, chapter 4 Setup, chapter 5 Alarm, chapter 6 Log out
for detailed information.
Figure 2-3
2.3 Video Window Function Option
The interface is shown as below. See Figure 2-4.
Figure 2-4
Please refer to the following sheet for detailed information.

Dahua Network Speed Dome Web3.0 Operation Manual
7
SN
Parameter
Function
1
Regional
Focus
Click the button and use mouse to select an area in the box
on the video screen, which will make the device auto focus in
the selected box area.
2
Remark
Click it and then select pen color, you can write down the
mark information on the preview interface.
3
Zoom
When the video is in the original status, click it you can
select any zone to zoom in. In the non-original status,
you can drag the zoom-in zone in specified range. Right
click mouse to restore previous status.
Click it; you can use the middle button of the mouse to
zoom in/out the video size.
4
Snapshot
Click the button to snapshot, save picture to path in Chapter
4.1.2.4.
5
Triple snap
Click it, system can snap at 1f/s. All images are saved to path
in Chapter 4.1.2.4.
6
Record
Click it, system can record. All images are saved to path in
Chapter 4.1.2.4.
7
Help
Click it to open help file.
2.4 Video Window Setup
The interface is shown as in Figure 2-5.
Figure 2-5
2.4.1 Image Adjustment
Click this button to display/hide image control interface. Click it to open picture setup interface. This
interface is on the top right pane. See Figure 2-6
Parameter
Function
Video
setup
It is to adjust monitor video
brightness.
Note:
All the operations here apply

Dahua Network Speed Dome Web3.0 Operation Manual
8
It is to adjust monitor video
contrastness.
to WEB end only.
Please go to Setup-
>Camera->Conditions to
adjust corresponding items.
It is to adjust monitor video
hue.
It is to adjust monitor video
saturation.
Reset R
e
Restore brightness,
contrastness saturation and
hue to system default setup.
Figure 2-6
2.4.2 Original Size
Click this button to go to original size. It is to display the actual size of the video stream. It depends on
the resolution of the bit stream.
2.4.3 Full Screen
Click it to go to full-screen mode. Double click the mouse or click the Esc button to exit the full screen.
2.4.4 Width and Height Ratio
Click it to restore original ratio or suitable window.
2.4.5 Fluency Adjustment
There are three levels of fluency for you to select (real-time, normal, fluent). The default is normal.
2.4.6 Rule Info
Click it to enable the function that the intelligent rule will be displayed in the live interface. The default is
enable.

Dahua Network Speed Dome Web3.0 Operation Manual
9
2.4.7 PTZ
Click it to open PTZ setup interface. Please refer to chapter 2.5 for detailed setup information.
2.5 PTZ Configuration
2.5.1 PTZ Control
Before PTZ operation, please make sure you have properly set PTZ protocol.
Parameter
Note
①Quick
Position
Use mouse to draw a box in monitoring video, PTZ will rotate and focus to
quickly positioning.
②PTZ direction
PTZ supports eight directions: left/right/up/down/upper left/upper right/bottom
left/bottom right.
③Speed
It controls rotation speed. The longer the step length, the higher the speed.
Step length control PTZ, zoom, focus and iris.
④Zoom/focus
Click to increase value and click to decrease value.
The PTZ setup/Menu interface is shown as in Figure 2-7.
Figure 2-7
2.5.2 Virtual Joystick

Dahua Network Speed Dome Web3.0 Operation Manual
10
The virtual joystick interface is shown as below. See Figure 2-8.
This function allows you to control the button in then center to simulate the joystick operation. You can
use it to control device movement.
Figure 2-8
2.5.3 PTZ Function
Click PTZ set button, the interface is shown as in Figure 2-9. Here you can select scan, preset, tour
pattern, assistant function and etc.
Figure 2-9
Please refer to the following sheet for PTZ setup information.

Dahua Network Speed Dome Web3.0 Operation Manual
11
Parameter
Function
Scan
Select Scan from the dropdown list, click Start button, you can
begin scan operation. Default SN is 1.
Preset
Input the preset value and then click View button, the camera
turns to the corresponding position of the preset.
Tour
Select Tour from the dropdown list and then click Start button,
you can begin tour.
Pattern
You can select Pattern from the dropdown list and then click
Start button to begin PTZ movement.
Assistant
Reserved assistant function.
Go to
It is the accurate positioning function. Please input
corresponding horizontal angle, tilt angle, and speed dome
zoom speed and then click Goto button to go to a specified
position.
One unit of the horizontal angle or tile angle stands for 0.1
degree.
For detailed setup information, please go to Setup->PTZ->Function.
Click button to begin a PTZ operation. Now you can see it becomes Stop button. Click it
again to stop current PTZ operation.

Dahua Network Speed Dome Web3.0 Operation Manual
12
3 Playback
Web client playback supports video playback and picture playback.
Note:
Before playback, user shall set storage management as in Chapter 4.5.
3.1 Playback
The playback interface is shown as in Figure 3-1.
Figure 3-1
There are six sections:
Section 1: Assistant function
Section 2: Playback file
Section 3: Clip
Section 4: Playback bar
Section 5: Record type
Section 6: Progress bar time format

Dahua Network Speed Dome Web3.0 Operation Manual
13
3.1.1 Function of Play
The function of play is shown as in Figure 3-2.
Figure 3-2
Parameter
Function
①Play
When you see this button, it means pause or not played record. Click this button,
switch to normal play status.
②Stop
Click this button to stop playing.
③Frame by
frame play
Click this button to go to next frame.
Note:
You shall pause record when you use this function.
④Slow
Click this button to play slowly.
⑤Quick
Click this button to play quickly.
⑥Mute
When this button displays, it means audio is silent. Click this button to switch
back to normal.
⑦Volume
Left click mouse to adjust volume.
3.1.2 Playback File
In calendar, blue date represents data currently has video record or snapshot. See Figure 3-3.

Dahua Network Speed Dome Web3.0 Operation Manual
14
Figure 3-3
Parameter
Function
File Type
Select “dav”, as video playback.
Select “jpg” as picture playback.
Data Source
Default is SD card.
Step 1.
Click data in blue, time axis displays record file progress bar in color. While, green represents normal
record, yellow represents motion detect record, red represents alarm record, and blue represents
manual record.
Step 2.
Step 3. Click certain time on progress bar, playback starts from this time. See Figure 3-4.
Figure 3-4
Step 4. Click file list , select date file will be displayed in list.
Step 5. Double click file in list, playback this file and display file size, start time and end time.
See Figure 3-5.

Dahua Network Speed Dome Web3.0 Operation Manual
15
Figure 3-5
Parameter
Function
Search
It means records within searched start time and end time on the date.
Record
Download
Format
There are two formats: dav, mp4.
Download
Record type is “dav”, click download button to download file to local.
Record type is “mp4”, click download button and download file to path in Ch
5.1.2.5.
Note:
System does not support download and playback of MP4 file.
Back
Click back button to go to calendar interface.

Dahua Network Speed Dome Web3.0 Operation Manual
16
3.1.3 Playback Cut (Clip)
Note:
Playback cut function will automatically pause playing record as playback cut and playback cannot be at
the same time.
Step 1.
Click start time to cut on time axis. This time must be within progress bar range.
Step 2.
Move mouse to cut icon . You will be ask to select start time. Click cut icon as finish cutting.
Step 3.
Click playback cut end time on time axis. This time must be within progress bar range.
Step 4.
Move mouse to cut icon , you will be asked to select end time. Click cut icon as finish
cutting.
Step 5.
Click Save button to save file cut to path in chapter 4.1.2.4. See Figure 3-6.
Figure 3-6
3.1.4 Record Type
Check record file type, only selected file will be displayed in progress bar and file list. See Figure 3-7.
Figure 3-7
3.1.5 Progress Bar Time Format
The interface is shown as in Figure 3-8.
Figure 3-8
Please refer to the following sheet for detailed information.