Dahua DH-SD6323E-H User manual

Intelligent Speed Dome Installation Manual
Version 3.1.0

i
Table of Contents
1INTELLIGENT SPEED DOME INSTALLATION..................................................1
1.1 Installation Preparation .........................................................................................................................1
1.2 Initial Setup.............................................................................................................................................2
1.3 Dial Switch Setup (For Analog Speed Dome, HDCVI Speed Dome) ............................................2
1.3.1 Dial Switch Description ....................................................................................................................2
1.3.2 Baud Rate and Parity.......................................................................................................................3
1.3.3 Address Setup...................................................................................................................................3
1.3.4 Terminal Matching Resistance Setup............................................................................................4
1.4 Reset and SD Card Installation (Network Speed Dome) ................................................................4
1.5 Installation...............................................................................................................................................5
2BRACKET DIMENSIONS .................................................................................11
2.1 Wall Mount Bracket .............................................................................................................................11
2.2 Corner Mount Bracket.........................................................................................................................11
2.3 Pole Mount Bracket .............................................................................................................................12
3WALL MOUNT BRACKET INSTALLATION......................................................13
3.1 Component Installation .......................................................................................................................13
3.2 Installation.............................................................................................................................................13
3.2.1 Installation Requirements..............................................................................................................13
3.2.2 Installation Steps.............................................................................................................................13

ii
4CORNER MOUNT BRACKET INSTALLATION ................................................15
4.1 Component Installation .......................................................................................................................15
4.2 Installation.............................................................................................................................................15
4.2.1 Installation Requirements..............................................................................................................15
4.2.2 Installation Steps.............................................................................................................................15
5POLE MOUNT BRACKET INSTALLATION ......................................................17
5.1 Installation Components .....................................................................................................................17
5.2 Installation.............................................................................................................................................17
5.2.1 Installation Requirements..............................................................................................................17
5.2.2 Installation Steps.............................................................................................................................17
6APPENDIX ⅠTHUNDER PROOF AND SURGE PROTECTION .......................19
7APPENDIX ⅡABOUT RS485 BUS ..................................................................20
7.1 RS485 Bus Main Feature ...................................................................................................................20
7.2 RS485 Bus Transmission Distance ..................................................................................................20
7.3 The Problem in Practical Use ............................................................................................................20
7.4 RS485 Bus FAQ ..................................................................................................................................21

iii
Welcome
Thank you for purchasing our speed dome!
Please read the following safeguards and warnings carefully before you install or use the
product!

iv
Important Safeguards and Warnings
Safety Measures
1. Qualified Engineer Needed
The installation engineer or maintenance engineer shall have corresponding CCTV system
installation certificate or maintenance qualification certificate.
The installation engineer or maintenance engineer shall have qualification certificate for work
at height.
The installation engineer or maintenance engineer shall have the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.
Please read the installation manual carefully and keep it well for future reference,
We are not liable for any problems caused by unauthorized modifications or attempted repair.
2. Lifting Appliance Requirement
Please select the proper speed dome installation mode and use the lifting appliances at the
safety environment.
The lifting appliances shall have the enough capacity to reach the installation height.
The lifting appliances shall have safe performance.
The precaution measures include two types: Warning and Note.
Warning: It is to alert you there is an optional risk of death or series injury!
Note: It is to alert you there is an optional risk of damage or property loss!
Warning
1. All installation and operation here should conform to your local electrical safety codes. We
assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2. Be sure to use all the accessories (such as power adapter) recommended by manufacturer.
3. Do not connect several speed domes to one power adapter. It may result in overheat or fire
if it exceeds the rated load.
4. Before you connect the cable, install or uninstall, or begin the daily maintenance work,
please turn off the power and unplug the power cable.
5. Please make sure the produce is secure firmly on the wall or the ceiling.
6. Please turn off the power and unplug the power cable, If there is any smoke, disgusting
smell, or noise. Please contact your local retailer or customer service centre for help.

v
7. All the examination and repair work should be done by the qualified service engineers. We
are not liable for any problems caused by unauthorized modifications or attempted repair.
Note
1. Safety Transportation
Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
This series product must use split type package during the transportation.
We are not liable for any damage or problem resulting from the integrated package during
the transportation.
2. When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contact your local retailer ASAP.
3. Do not try to dismantle or modify the device
There is risk of personal injury or device damage resulting from opening the shell.
Please contact your local retailer if there is internal setup or maintenance requirement.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
4. Do not allow other object falling into the device
Please make sure there is no metal or inflammable, explosive substance in the speed dome.
The above mentioned objects in the device may result in fire, short-circuit or damage.
Please shut down the device and disconnect the power cable if there is water or liquid falling
into the camera. Please contact your local retailer ASAP.
Please pay attention to the camera. Avoid the sea water or rain to erode the camera.
5. Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
6. Installation Environment Requirement
This series speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
This series product shall be away from the strong electromagnetism radiant, please keep it
away from wireless power, TV transmitter, transformer and etc.
7. Daily Maintenance
Please use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning
liquid to clean the shell and then use soft cloth to make it dry.

vi
Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shell transfiguration or paint flake.
Do not allow the plastic or rubber material to touch the shell for a long time. It may result in
paint flake.

1
1INTELLIGENT SPEED DOME INSTALLATION
1.1 Installation Preparation
Basic Requirement
All installation and operation here should conform to your local electrical safety codes.
Before installation, please open the package and check all the components are included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirement, please contact your local retailer for more
information.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Check installation space and installation location intension
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. It shall sustain the 8X weight of the speed dome.
About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
75 ohm.
Full cable with copper conductor
95% knitted copper shield
International Model
Max Distance
(Ft\M)
RG59/U
750Ft (229M)
RG6/U
1,000Ft (305M)
RG11/U
1,500Ft (457M)
Note: The above can be applied to analog speed dome and network speed dome
International Model
Max Distance
(M\Ft)
SYV-75-3
720P（25fps\30fps)：500M/1640Ft
720P（50fps\60fps)：300M/984Ft
1080P（25fps\30fps):300M/984Ft
Note: The above can be applied to HDCVI speed dome
Set dial switch button
Set dial switch button according to control protocol and speed dome address. (Please refer to
user’s manual for detailed information.)
Please keep all package material well for future use
Please keep speed dome package material well in case you need to send it back to your local
retailer or manufacturer for maintenance work.

2
Non-original package material may result in device damage during the transportation.
Check Accessories
Before the installation, please check the accessories one by one according to the packing list.
Please make sure all the components listed are included.
1.2 Initial Setup
The default setup is:
Address: 1
Baud rate: 9600
Party: none
120Ωmatched resistance: OFF
1.3 Dial Switch Setup (For Analog Speed Dome, HDCVI Speed Dome)
1.3.1 Dial Switch Description
Before you control the speed dome, please set the address, baud rate and parity first so that the
speed dome can has response to the control command. See Figure 1-1.
▲Note：
Open the transparent enclosure of the speed dome; you can see the dial switch button on the
PTZ main board. Please follow the steps listed below to set the baud rate, address, parity and
etc. After some related information has been reset, users have to cut the power and reboot the
speed dome to activate new setup!
SW2, SW3 are the two dial switches on the PTZ of the speed dome which are used to confirm
the parameters such as the address, Baud rate and parity. When the button is ON, it is 1. For
SW2 dial switch, 1 is the lowest bit and the 8 is the highest bit. For SW3, 1 is the lowest bit and
4 is the highest bit. (Intelligent speed dome self-adapt PELCO-D, PELCO-P, industry standard
protocol, there is no need to pass dial switch setup for the control protocol).
Figure 1-1

3
1.3.2 Baud Rate and Parity
The dial switch SW3 is to set speed dome baud rate and parity. It ranges from 1 to 4. The 1st and
the 2nd are to set baud rate. The 3rd and the 4th are to set parity. See Figure 1-2.
Figure 1-2
Please refer to the baud rate sheet for detailed information.
1
2
Baud Rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
Please refer to the parity setup sheet for detailed information.
3
4
Parity
OFF
OFF
NONE
ON
OFF
EVEN
OFF
ON
ODD
ON
ON
NONE
1.3.3 Address Setup
Please refer to Figure 1-3 for SW2 address setup. The speed dome use dial switch to set
address number, encode mode adopts binary coding. Bit 1-8 is valid bit; the highest address bit
is 255.
Figure 1-3
You can refer to the following sheet for more information.
Address
1
2
3
4
5
6
7
8
1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
……
…………………………………………………………………
254
OFF
ON
ON
ON
ON
ON
ON
ON

4
255
ON
ON
ON
ON
ON
ON
ON
ON
1.3.4 Terminal Matching Resistance Setup
There is terminal resistance 120Ω on the power board. There are two connection modes: See
Figure 1-4.
Figure 1-4
The factory default connection mode is shown as in Figure 1-5. Right now, the jumper on the
power board (Connection board) is on the pin 2 and pin 3. The 120Ω resistance does not connect
to the device.
Figure 1-5
If you want to connect the 120Ω resistance, please remove the jumper from the pin 2 and pin 3
and connect to pin 1 and pin 2. Now the 120Ω is connected to the circuit. See Figure 1-6.
Figure 1-6
1.4 Reset and SD Card Installation (Network Speed Dome)
After opening the speed dome, you can see there is a reset button and Micro-SD card on the
PTZ mainboard, see Figure 1-7 for more details. Reset button can be used to restore network
system and Micro-SD card can be used for data storage.
1-2
2-3
120Ω
ON
OFF

5
Figure 1-7
SD card of network speed dome should be installed on the module, see Figure 108 for more
details.
Figure 1-8
Note:
Please contact the technical support of our company if you have any questions.
1.5 Installation
Installation here includes intelligent analog speed dome, intelligent network speed dome,
intelligent auto-tracking speed dome and etc.

6
The speed dome has several types of installation brackets. You can refer to the chapter 3 to
chapter 5 for detailed information. Here we are going to install the speed dome in wall mount
bracket.
Step 1 Remove the package and then take out the device.
Step 2 Open the transparent cover and take out the EPE around the speed dome driver. Please
remove the protective paster from the driver and take off the camera lens cap. See Figure 1-9.
Figure 1-9
Step 3 Set Dial Switch of Intelligent Speed Dome (Analog Speed Dome)
Set the parameters of intelligent speed dome address, Baud rate and so on. There are SW2 and
SW3 two dial switches on the PTZ, which are used to set the parameters of address, Baud rate
and so on, see Figure 1-10 for more details, and see “1.3 Dial Switch Setup (For Analog Speed
Dome, HDCVI Speed Dome) for the way to set.
Figure 1-10
Step 4 Install the Transparent Cover

7
1. Please note you need to check the steel wire of the bracket is firmly secure or not.
2. Please line up the captive screws to the quadrate groove of the bracket and then push the
bracket into the internal enclosure. Fix these two captive screws. See Figure 1-11.
Figure 1-11
Step 5 Wall Mount Bracket Installation
1. Pull the composition cable of the intelligent speed through the other end of the wall mount
bracket via the end of column of the wall mount bracket. See Figure 1-12.
2. Line up the straight line marginal of the wall mount bracket to the straight line marginal of the
internal enclosure of the intelligent speed dome. Push the intelligent speed dome to the wall
mount bracket along the straight line marginal. See Figure 1-12.
Figure 1-12
3. Use the hex wrench to turn the M6*16 inner hex stainless screw of the wall mount bracket to
the Ф6.5 round hole bottom of straight line marginal of speed dome internal enclosure. Please
note, the step here is very important. Please make sure the screw is completely turned into the
bottom of the Ф6.5 round hole. Otherwise there is falling risk of intelligent speed. See Figure 13
and 14 for more details.

8
Figure 1-13
Figure 1-14
4. Use the hex wench to fix the other two M6*10 inner hex stainless screws (with spring washer)
of the bracket to secure the speed dome. See Figure 1-15.

9
Figure 1-15
5. After the installation; please use the hex wrench to secure the three M6 stainless screws.
Please make sure these three M6 stainless screws are firm so that it can secure the speed dome
on the wall mount bracket. Otherwise there is falling risk of the speed dome if these three screws
are not in the proper position.
Step 6 Secure the Speed Dome
Please select the installation wall. Please make sure the wall is thick enough to install the
expansion bolt. Please refer to chapter 3 for detailed information.
Note:
The wall can at least sustain the 8x weight of the speed dome, bracket and other accessories.
Step 7 Cable Connection
Connect the reserved integration cable of the intelligent speed dome to the corresponding power
cable, video output cable, RS485 control cable, alarm input/output port(if necessary) of the
multiple-function composite cable of the quick installation speed dome. Paste the insulating tape
in the connection position to do the proper waterproof work.
Note:
The video port is covered the heat shrink tube of high shrinking ratio. After the video connection,
please heat the tube to make sure the video port is damp proof and water proof.
Step 8 The installation of speed dome is completed, see Figure 1-16 for more details.

10
Figure 1-16

11
2BRACKET DIMENSIONS
2.1 Wall Mount Bracket
The wall mount bracket dimensions are shown as below. The unit is mm. See Figure 2-1.
3-M6均布
58.00
145
10
110
110
84
145
119
4-Ф9
235.00
Figure 2-1
2.2 Corner Mount Bracket
The corner mount bracket is shown as below. The unit is mm. See Figure 2-2.

12
Figure 2-2
2.3 Pole Mount Bracket
The corner mount bracket is shown as below. The unit is mm. See Figure 2-3.
Figure 2-3

13
3WALL MOUNT BRACKET INSTALLATION
3.1 Component Installation
Wall mount bracket is shown as below. See Figure 3-1.
Figure 3-1
3.2 Installation
3.2.1 Installation Requirements
The wall mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:
The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 8x weight of the speed dome.
3.2.2 Installation Steps
1).Please draw four holes position in the wall according to the hole of the bottom of the wall
mount bracket. Then you can dig four holes and insert the expansion bolts (not provided). Use
four hex bolts and flat washer to fix the bracket in the expansion bolts. See Figure 3-2.
Figure 3-2
2). Install the speed dome in the bracket. Please refer to chapter 1.5 for detailed installation
information. See Figure 3-3.