Dahua IPC-HDB/HDBW3202 Series User manual

HD (IR) Vandal Proof Network Dome Camera User’s Manual
Version 1.0.1

i
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. Please note: Do not connect these two
power supplying sources to the device at the same time; it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding holes of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name Amount
Network Camera 1
Quick Start Guide 1
CD 1
Installation Accessories Bag 1

iv
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
1.3.1 Performance...........................................................................................................2
1.3.2 Factory Default Setup...........................................................................................3
2Structure ....................................................................................................................................11
2.1 Dimensions..................................................................................................................11
2.2 Port Description ..........................................................................................................11
2.3 Bidirectional talk .........................................................................................................15
2.3.1 Device Connection ..............................................................................................15
2.3.2 Operation ..............................................................................................................15
2.4 Alarm Setup.................................................................................................................15
3Installation .................................................................................................................................17
3.1 Device Installation Introduction ................................................................................17
3.2 Device Installation Steps...........................................................................................17
3.2.1 General Installation .............................................................................................17
3.2.2 Manual Zoom Lens Focus Operation...............................................................21
3.2.3 Side Cable Exit ....................................................................................................21
3.2.4 Cable Connection................................................................................................22
3.3 SD Installation.............................................................................................................23
4Quick Configuration Tool.........................................................................................................24
4.1 Overview......................................................................................................................24
4.2 Operation .....................................................................................................................24

v
5Web Operation..........................................................................................................................27
5.1 Network Connection...................................................................................................27
5.2 Login and Main Interface...........................................................................................27
6FAQ ............................................................................................................................................30
Appendix Toxic or Hazardous Materials or Elements ...............................................................31

1
1General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
audio and video data collection, transmission together. It can connect to the network directly without any
auxiliary device.
This series network camera uses standard H.264 video compression technology and G.711a audio
compression technology, which maximally guarantee the audio and video quality.
This series network camera enclosure has the strong resistance capacity, which can guarantee the
proper work performance under heavy strike. It supports real-time monitor and listening at the same time.
It supports analog video output and dual-way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the network
and then use a network client-end. Due to its multiple functions and various uses, this series network
camera is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
zDifferent user rights for each group, one user belongs to one group.
zThe user right shall not exceed the group right.
Storage
Function
zSupport central server backup function in accordance with your configuration and
setup in alarm or schedule setting
zSupport record via Web and the recorded file are storage in the client-end PC.
zSupport built-in SD card.
zSupport local SD card hot swap, support short-time storage when encounter
disconnection.
Alarm
Function
zReal-time respond to external local alarm input and video detect as user pre-
defined activation setup and exert corresponding message in screen and audio
prompt(allow user to pre-record audio file)
zReal-time video detect: motion detect, camera masking.
zCan generate an alarm when network abnormal, SD card abnormal event
occurred.
Network
Monitor
zNetwork camera supports one-channel audio/video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
zMax supports 20 connections.
zAdopt the following audio and video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
zSupport web access, widely used in WAN.
Network
Management
zRealize network camera configuration and management via Ethernet.
zSupport device management via web or client-end.
zSupport various network protocols.
Peripheral
Equipment
zSupport the on-off alarm device to alarm via the sound or the light.
Power zExternal power adapter DC12V/AC 24V
zSupport PoE.
Assistant
Function
zLog function
zSupport PAL/NTSC

2
zSupport system resource information and running status real-time display.
zDay/Night mode auto switch (electromagnetic ICR switch).
zBuilt-in IR light. Support IR night vision (For HDBW Series only).
zBacklight compensation: screen auto split to realize backlight compensation to
adjust the bright.
zSupport electronic shutter and gain setup.
zSupport video watermark function to avoid vicious video modification.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
Model
Parameter IPC-HDB/HDBW3202 Series IPC-HDB/HDBW3101 Series
Main
Processor TI Davinci high performance DSP
OS Embedded LINUX
System
Resources Support real-time network, local record, and remote operation at the same time.
User Interface Remote operation interface such as WEB, DSS, PSS
System
System Status SD card status, bit stream statistics, log, and software version.
Image Sensor 1/3-inch CMOS
Pixel 1920（H）*1080（V）1280(H)*960(V)
Day/Night
Mode Support day/night mode switch and electromagnetic IR-CUT at the same time.
Auto Iris DC drive
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC Manual/Auto
Electronic
Shutter
Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Motorized
Focus Support remote motorized focus function.
Video
Compression
Standard H264/JPEG/MJPEG
Video Frame
Rate
PAL:
Main stream（1920*1080@25fps）
extra stream（704*576@25fps）
NTSC:
Main stream（1920*1080@30fps）
extra stream（704×480@30fps）
PAL:
Main stream（1280*960@25fps）
Extra stream（704*576@25fps）
Main stream（1280*720@25fps）
extra stream（704*576@25fps）
NTSC:
Main stream（1280*960@30fps）
extra stream（704×480@30fps）
Main stream（1280*720@30fps）
extra stream（704×480@30fps）
Video Bit Rate
H.264: 56Kbps-8192Kbps. It is adjustable
ＭJPEG: 128Kbps-0480Kbps. It is adjustable and bit rate is adjustable.
Support customized setup.
Video Parameter
Video Flip Support mirror.
Support flip function.

3
Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Information Channel title, time title, motion detect, privacy mask.
Lens [email protected] motorized zoom
focus lens [email protected]
Lens Interface ¢14. Lens is the default accessories.
Audio Input 1-channe
Audio Output 1-channel
Bidirectional
Talk Input Reuse the first audio input channel
Audio Bit Rate 16kbps 16bit
Audio
Audio
Compression
Standard G.711a/G.711u/PCM
Motion Detect
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Video
Video Loss Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Alarm Input 1-channel input，1-channel output
Record
Priority Manual>External alarm >Video detect>Schedule
Record and Backup
Local Storage Support Micro SD card storage
Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol HTTP,TCP,ARP,RTSP,RTP,UDP,RTCP,SMTP,FTP,DHCP,DNS,DDNS,PP POE,IPv4/v6,SNMP,QoS,UPnP,NTP.
Network
Remote
Operation Monitor, system setup, log information, maintenance , upgrade and etc
Video Output 1-channel analog video output，BNC port, 9-pin port connection
Reset Built-in RESET button
AUX
Interface
IR light IR distance 10 to 20 meters (For HDBW series product only)
Power Support AC24V/DC12V power. PoE
Power
Consumption General series: below 5W. IR series: below 7W.
General series: below 3W.
IR series: below 5W.
Working
Temperature -10℃~+60℃
Working
Humidify 10%~90%
Dimensions(m
m) ¢151x119
Weight 1.25Kg
General Parameter
Installation Support various installation modes
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.

4
Default setup
Function
Setup Type Item IPC-
HDB/HDBW320
2 Series
IPC-
HDB/HDBW31
01 Series
Brightness 50
Contrast 50
Hue 50
Saturation 50
Gain mode Auto
Gain limit 80
Exposure mode Auto
Auto iris Enable
Scene mode Auto
Day/night mode Auto
BLC Off
Conditions
Flip Disable
Bit stream
type General
Encode
mode H.264B
Resolution 1080P
（1920*1080）
720P
(1280*720)
Frame rate
（FPS）
PAL: 25
NTSC:30
Bit stream
type CBR
Reference bit
rate 3584-8192 Kb/S
Bit rate 8192
I frame
interval 50
Watermark
settings Enable
Main
stream
Watermark
character DigitalCCTV
Enable Enable
Bit stream
type General
Encode
mode H.264B
Resolution CIF(352×288/35
2×240)
CIF(352×288/3
52×240)
Frame rate
（FPS）
PAL: 25
NTSC:30
Bit rate type CBR
Camera Setup
Video
Video bit
stream
Extra
stream
Reference bit
rate 192-1024Kb/S

5
Default setup
Function
Setup Type Item IPC-
HDB/HDBW320
2 Series
IPC-
HDB/HDBW31
01 Series
Bit rate 640
I frame
interval 50
Snap type General snap
Image size 1080P
（1920*1080）
720P
(1280*720)
Quality Better
Snapshot
Interval 7s
Privacy mask Enable
Channel title Enable
Overlay
Time title Enable
Snapshot
path C:\PictureDownload
Path
Record path C:\RecordDownload
Enable Enable
Main stream Encode
mode G.711A
Enable Disable
Audio
Sub(Extra) stream Encode
mode G.711A
Host name IPC
Ethernet card Wire(Default)
Mode Static
MAC
address Depends on the device
IP version IPV4
IP address 192.168.1.168
Subnet mask 255.255.255.0
Default
gateway 192.168.1.1
Preferred
DNS 8.8.8.8
Alternate
DNS 8.8.8.8
TCP/IP
Enable
ARP/Pingto
to set IP
address
service
Enable
Max
connection 10
TCP port 37777
Network setup
Connection
UDP port 37778

6
Default setup
Function
Setup Type Item IPC-
HDB/HDBW320
2 Series
IPC-
HDB/HDBW31
01 Series
HTTP port 80
RTSP port 554
Enable Disable
User name N/A
PPPoE
Password N/A
Server type Disable ，CN99 DDNS
Server IP none
Port 80
Domain
name none
User name none
Password N/A
DDNS
Update
period 5m
IP filter Trusted sites Disable
SMTP server none
Port 25
Anonymity Disable
User name anonymity
Password N/A
Sender none
Authenticatio
n (Encrypt
mode)
N/A
Title
(Subject) IPC Message
Main
Receiver N/A
Interval 0s
SMTP（email）
Health email Disable ，interval=60m
UPnP Enable UPnP Disable
SNMP v1 Disable
SNMP v2 Disable
SNMP port 161
Read
community public
Write
community private
Trap address N/A
SNMP
Trap port 162
Bonjour Enable
Enable

7
Default setup
Function
Setup Type Item IPC-
HDB/HDBW320
2 Series
IPC-
HDB/HDBW31
01 Series
Server name “Device name+SN”.
Depends on the device.
Multicast
address 239.255.42.42
Multicast
Port 36666
Enable Disable
SN 1
Server IP 0.0.0.0
Port 7000
Auto register
Sub-device
ID none
WIFI On(Enable) Enable
Real-time
monitor 0
QoS
Command 0
Enable Disable
Anti-dither 5 seconds
Sensitivity 3
Record
Channel Enable
Record
Delay 10 seconds
Relay
(Alarm)
output
Enable
Alarm delay 10s
Send email Disable
Activation N/A
Address 0
Motion detect
Snapshot Disable
Enable Disable
Record
Channel Enable
Record
Delay 10 seconds
Relay out Enable
Record
Delay 10 seconds
Send email Disable
Activation Disable
Event
management
Video detect
Video (Camera) masking
Address 0

8
Default setup
Function
Setup Type Item IPC-
HDB/HDBW320
2 Series
IPC-
HDB/HDBW31
01 Series
Snapshot Disable
Enable Disable
Relay input Alarm1
Anti-dither 5s
Sensor type NO
Record
channel Enable
Record delay 10s
Relay
(Alarm)
output
Enable
Relay
(Alarm) delay 10s
Send email Disable
Activation N/A
Address 0
Relay (Alarm) activation
Snapshot Disable
Alarm setup
Relay (Alarm)
output 1
Enable Disable
Relay
(Alarm)
output
Enable
Relay output
delay 10s
No SD card
Send email Disable
Enable Disable
Capacity limit
(Space
threshold)
10%
Relay
(Alarm)
output
Enable
Relay output
delay 10s
Capacity warning
Send email Disable
Enable Disable
Relay
(Alarm)
output
Enable
Relay output
delay 10s
Abnormity
SD card error
Send email Disable

9
Default setup
Function
Setup Type Item IPC-
HDB/HDBW320
2 Series
IPC-
HDB/HDBW31
01 Series
Enable Disable
Record Enable
Record delay 10s
Relay
(Alarm)
output
Enable
Disconnection
Relay output
delay 10s
Enable Disable
Record Enable
Record delay 10s
Relay
(Alarm)
output
Enable
IP conflict
Relay output
delay 10s
FTP enable Disable
Server IP N/A
Port 21
User name anonymity
Password N/A
Remote
storage path share
FT
P
Emergency
storage to
local path
Disable
NAS enable Disable
Mode NFS
Server IP N/A
Port 21
User name N/A
Password N/A
Destination(Storag
e )
Network storage
Remote
storage path N/A
Pack
duration 8m
Pre-record 5s
Disk full Overwrite
Storage
management
Conditions (Record
control)
Record mode Auto
Device name Device factory SN
System
management
General setup
al setu
Language English

10
Default setup
Function
Setup Type Item IPC-
HDB/HDBW320
2 Series
IPC-
HDB/HDBW31
01 Series
Video
standard NTSC NTSC
Date format Y-M-D
Time format 24H
Time zone GMT+08:00
Current time Sync PC
DST Disable
DTS type Week
Start time 00:00:00 of the first Sunday of the
month
End time 00:00:00 of the second Monday of
the month
Synchronize
with NTP Disable
NTP server clock.isc.org
Port 37
Date and time
Update
period 10m
Auto reboot Enable
Auto maintenance Auto delete
old files Disable

11
2Structure
2.1 Dimensions
You can refer to the following figures for dimension information. The Unit is mm. See Figure 2-1 and
Figure 2-2.
Figure 2-1
Figure 2-2
2.2 Port Description
For the non-IR series product, the interface is shown as in Figure 2-3 and Figure 2-4.

12
Figure 2-3
Figure 2-4
For the IR motorized zoom lens series product, the interface is shown as in Figure 2-5 and Figure 2-6.

13
Figure 2-5
Figure 2-6
For the IR manual zoom lens series product, the interface is shown as in Figure 2-7 and Figure 2-8.

14
Figure 2-7
Figure 2-8
Please refer to the following sheet for detailed information.
SN Definition
1 AC 24V power port. The middle pin is for GND.
2 DC 12V power port. The left is the negative end and the right
is the positive end.
3 External cable exit.
4 RJ45 network port.