Dahua IPC-HDBW5502N User manual

HD (IR) Vandal Proof Network Dome Camera
Quick Start Guide
Version 1.3.0

i
Welcome
Thank you for purchasing our network camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Before your operation please read the following instructions carefully.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.

ii
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1

iii
Table of Contents
1Structure ......................................................................................................................................1
1.1 Dimensions....................................................................................................................1
1.2 Port Description ............................................................................................................1
1.3 Bidirectional talk............................................................................................................7
1.3.1 Device-end to PC-end..........................................................................................7
1.3.2 PC-end to the Device-end....................................................................................7
1.4 Alarm Setup...................................................................................................................8
2Installation..................................................................................................................................10
2.1 Device Installation Introduction ................................................................................10
2.2 Device Installation Steps...........................................................................................11
2.2.1 Installation Steps for Devices of Following Product Models:
HDB/HDBW3202, HDB/HDBW3101, HDB/HDBW5202, HDB/HDBW5302,
HDB/HDBW5502, HDB/HDBW8301, HDB/HDBW8306...........................................11
2.2.2 Manual Zoom Lens Focus Operation...............................................................14
2.2.3 Side Cable Exit....................................................................................................15
2.2.4 Cable Connection................................................................................................16
2.2.5 Installation Steps for Devices of Following Product Models: HDBW8351E,
HDBW8356E....................................................................................................................16
2.2.6 Manual Zoom Lens Focus Operation...............................................................19
2.2.7 Side Cable Exit....................................................................................................20
2.2.8 Cable Connection................................................................................................20
2.3 Micro SD Card Installation ........................................................................................21
3Quick Configuration Tool.........................................................................................................23
3.1 Overview......................................................................................................................23
3.2 Operation.....................................................................................................................23
4Web Operation..........................................................................................................................25
4.1 Network Connection...................................................................................................25
4.2 Login and Main Interface...........................................................................................25
Appendix Toxic or Hazardous Materials or Elements ...............................................................27

1
1Structure
1.1 Dimensions
You can refer to the following figures for dimension information. The Unit is mm. See Figure 1-1 and
Figure 1-2.
Figure 1-1 Dimension 1
Figure 1-2 Dimension 2
1.2 Port Description
For the non-IR series product, the interface is shown as in Figure 1-3 and Figure 1-4.
Note：
Figure in this chapter are all for reference only, and please refer to model 1-a and 1-b
according to actual product.

2
Figure 1-3 Camera internal without IR (1-a)
Figure 1-4 Camera internal without IR (1-b)
See Figure 1-5.

3
Figure 1-5 Camera internal without IR (2)
See Figure 1-6, Figure 1-7 and Figure 1-8.
Figure 1-6 Motorized focus camera internal with IR (1-a)

4
Figure 1-7 Motorized focus camera internal with IR (1-b)
Figure 1-8 Motorized focus camera internal with IR (2)
See Figure 1-9, Figure 1-10 and Figure 1-11.

5
Figure 1-9 Manual focus camera internal with IR (1-a)
Figure 1-10 Manual focus camera internal with IR (1-b)

6
Figure 1-11 Manual focus camera internal with IR (2)
Please refer to the following sheet for external connection port definition information.
SN
Port
Port Name
Connector
Function Description
1
POWER
AC 24V power
port
/
Connect to AC 24V power.
2
POWER
DC 12V power
port
/
Connect to DC 12V power.
3
Cable exit
of the
external
connected
cable
/
/
Cable exit.
4
LAN
RJ45 network
port
Ethernet port
Network cable port.
5
I/O
I/O port
/
It includes alarm input/output, audio
and analog output.
6
RESET
Reset button
/
Reset button. It is to restore factory
default setup.
7
AUTO
FOCUS
5-direction button
/
Adjust lens angle of view and
definition.
Note: Only some models have this
function.
8
Status
indicator
light
/
/
Display device running status.
9
Fan port
/
/
Connect to fan to reduce device
internal problem.
Please note this component is
optional.
10
Micro SD
Micro SD card
slot entry
Micro SD
card
Connect to Micro SD card to realize
local storage.
11
POWER
12V power port
/
The power port of the external
connected cable.

7
Default input is DC 12V.
12
LAN
Network port
Ethernet port
The network port of the
external connected cable.
Connect to standard Ethernet
port.
Support PoE.
Note:
Before making crystal head,
pull the anti-dust cover through
network cable.
Please refer to the following sheet for I/O port cable function information. Note: actual product may
vary.
Port
Name
Cable SN
Cable Port Name
Function Description
I/O Port
1
ALARM_NO
Alarm output port. Output alarm signal to
alarm device.
NO: Normal open alarm output end.
2
ALARM_COM
Alarm output public end.
3
GND
Ground end.
4
ALARM_IN
Alarm input port. It is to receive the on-off
signal from the external alarm source.
5
GND
Ground end.
6
AUDIO_IN
Input audio signal. It is to receive the analog
audio signal from the devices such as
pickup.
7
AUDIO_OUT
Output audio signal to devices such as
sound box.
8
GND
Ground end.
9
VIDEO_OUT
Output analog video signal. It can connect
to TV monitor to view video.
1.3 Bidirectional talk
1.3.1 Device-end to PC-end
Device Connection
Please connect the speaker or the MIC to the audio input port of the device. Then connect the
earphone to the audio output port of the PC.
Login the Web and then click the Talk button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the bidirectional talk function.
Click Talk button again to stop the bidirectional talk function.
Listening Operation
At the device end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the pc-end.
1.3.2 PC-end to the Device-end
Device Connection

8
Connect the speaker or the MIC to the audio input port of the PC and then connect the earphone to
the audio output port of the device.
Login the Web and then click the Talk button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Talk button again to stop the bidirectional talk function.
Please note the on-site listening operation is null during the bidirectional talk process.
Listening Operation
At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the earphone
or sound box at the device-end.
1.4 Alarm Setup
The alarm interface is shown as in Figure 1-12. Please follow the steps listed below for local alarm
input and output connection.
1) Connect the alarm input device to the alarm input port (No.4 pin) of the I/O cable.
2) Connect the alarm output device to the alarm output port (No.1 pin) and alarm output public port
(No.2 pin). The alarm output port supports NO (normal open) alarm device only.
3) Open the Web, go to the Figure 1-12. Please set the alarm input 01 port for the first channel of the
I/O cable (No.4 pin). Then you can select the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is the
No.1 pin of the I/O cable.
Figure 1-12 Alarm
Please refer to the following figure for alarm input information. See Figure 1-13.
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of
the alarm input port. When the input signal is connected to the 5V or is idle, the device collects the
logic “1”. When the input signal is grounded, the device collects the logic “0”.

9
Figure 1-13 Alarm input
Please refer to the following figure for alarm output information. See Figure 1-14.
Port ALARM_COM and Port ALARM_NO composes an on-off button to provide the alarm output.
If the type is NO, this button is normal open. The button becomes on when there is an alarm output.
If the type is NC, this button is normal off. The button becomes off when there is an alarm output.
Figure 1-14 Alarm output

10
2Installation
Important
Before you complete the installation and setup, do not remove the electrostatic attraction
film on the transparent enclosure. Otherwise it may result in injury.
After remove electrostatic attraction film, do not touch dome enclosure in case it may
leave stain.
Before the installation, please make sure the installation surface can sustain at least 3X
weight of the bracket and the camera.
2.1 Device Installation Introduction
Device of following product models: HDB/HDBW3202, HDB/HDBW3101, HDB/HDBW5202,
HDB/HDBW5302, HDB/HDBW5502, HDB/HDBW8301, HDB/HDBW8306.
Please refer to Figure 2-1 for device installation space information. You can use screws (diameter is
less than 4.5mm) to secure the device. You can see there are installation position map and installation
screws in the accessories bag for you to install the device conveniently.
Figure 2-1
Device of following product models: HDBW8351E, HDBW8356E.
Please refer to Figure 2-2 for device installation space information. You can see there are installation
position map and installation screws in the accessories bag for you to install the device conveniently.

11
Figure 2-2
2.2 Device Installation Steps
2.2.1 Installation Steps for Devices of Following Product Models: HDB/HDBW3202,
HDB/HDBW3101, HDB/HDBW5202, HDB/HDBW5302, HDB/HDBW5502, HDB/HDBW8301,
HDB/HDBW8306.
The interface is shown as in Figure 2-3.
IR Motorized Zoom Lens Series Non-IR Series IR Manual Zoom Series
Figure 2-3
Step 1
Take the installation position map from the accessories bag and then paste it on the installation ceiling
or the wall according to the monitor area. Please dig three bottom holes of the plastic expansion bolts
according to the map. Take three expansion bolts from the accessories bag and then insert them to
the holes you just dug and then fix firmly. If you need to dig a hole to pull through the cable, you need
to dig a cable exit hole (The diameter is more than 28mm) on the installation surface according to the
installation positioning map.
Step 2

12
Use the inner hex wrench from the accessories bag to unfasten the 3 hex screws on the dome camera
enclosure to open it.
Step 3
Please remove the device cable (Provided) network port and the power terminal. Use the inner hex
wrench (Provided) to remove the 2 inner hex screws from the dome driver module. Then please follow
the prompt on the device to push the metal hook to two sides. Remove the dome driver module from
the chassis. See Figure 2-4.
Figure 2-4
Step 4
Adjust the chassis of the device to the proper position and pull the cable to the cable exit of the
installation surface. Line up the holes of the chassis to the three expansion bolt holes you dug in Step
1. Take three ST3.0 self-tapping screws and secure them in the three plastic expansion bolts. Now the
chassis is secure on the installation surface.
Important
Please earth the device GND hole (GND) to enhance the reliability of the device. The GND
port is near the cable exit of the rear panel. The GND screw thread specification is M3-6mm.
Figure 2-5

13
Step 5
Please refer to the Step 3 to put the driver module back to the metal hooks of the chassis. Then use
the inner hex wrench to secure the two inner hex screws to the chassis. Then connect the network
cable and the power terminal.
Step 6
Adjust the lens to the proper angle according to your monitor requirements.
a) For the IR series product, you can skip current step and go the step b) directly. For the non-IR
series product, push the port slightly to remove the decoration enclosure from the black plastic
enclosure. See Figure 2-6.
Figure 2-6
b) Lens pan rotation angle setup. Please refer to Figure 2-7 to unfasten the lock screw A and adjust
the pan monitor angle to the proper position. Then fix the lock screw A. The pan angle ranges from
0°~+350°.
Lock Screw A
Adjust lens pan rotation
angle.

14
Figure 2-7
c). Lens tilt rotation angle. Please refer to Figure 2-8 to unfasten the lock screw B and lock screw C
and adjust the tilt monitor angle to the proper position. Then fix the lock screw B and lock screw C. The
tilt angle ranges from -23°~+73°.
d). Image pan rotation angle setup. Please refer to Figure 2-8 to turn lock screw D to adjust the video
pan angle. Then fix the lock screw B and C. The video pan angle ranges from 0°~+350°.
Figure 2-8
e) For the motorized zoom series product, please skip current step. Please refer to chapter 2.2.2 for
the lens zoom and focus operation of the manual focus series product.
f) For the IR series product, please skip current step and complete the angle setup directly. For the
non-IR series product, please put back the black plastic decoration enclosure to complete the angle
setup.
Important
Please note Figure 2-7 and Figure 2-8 is based on the IR motorized zoom camera. For the IR
manual zoom camera and non-IR series product, the lock screw position and the lens angle
adjustment are the same.
Step 7
Line up the dome camera protection enclosure to the cable exit on the side panel. Put the enclosure
back and then use the inner hex wrench to secure the 3 inner hex screws firmly. Now the installation is
complete.
Note
Usually we recommend, after the installation, please take the three white static protection gaskets from
the accessories bag and insert them to the screw holes of the protection enclosure. It is to enhance
device reliability.
2.2.2 Manual Zoom Lens Focus Operation
The manual zoom lens focus interface is shown as in Figure 2-9.
Lock screw B/C
Adjust lens tilt rotation
angle.
Lock screw D
Adjust lens pan rotation
angle.

15
Step 1
Slightly loosen the adjusting screw E and push the adjust screw E to make it swing. Adjust the lens
focus to the proper position according to the displayed video.
Step 2
Slightly loosen the adjusting screw F and push the adjust screw F to make it swing. Adjust the lens to
get the clear video and then fix the adjusting screw firmly.
Step 3
When you are securing the adjusting screw F, you can see the video may become blur. Please push
the adjusting screw E to adjust the video slightly. Please secure the adjust screw E if you get a clear
video.
Figure 2-9
2.2.3 Side Cable Exit
If you adopt side cable exit when you are installing the device, you need to remove the plastic
decoration plug from the side of the chassis. Use the proper tool to dig through the part specified in
Figure 2-10 to form a cable exit. Put the plastic decoration plug back to the chassis and then pull the
cable through the side panel of the chassis.
Figure 2-10
For some special user, he may need the metal protection tube to protect when he pulls through the
cable from the side cable. There is PG11screw thread port when you pull through the cable from the
Dig through here
Adjusting Screw E
Adjusting Screw F

16
side panel. Please remove the plastic decoration plug from the side panel of the chassis and pull
through the cable to the tunnel of the PG11 screw thread. Now secure the tunnel in the PG11 screw
threaded hole of the device.
2.2.4 Cable Connection
The device reserves two cable exits. The pin diameter shall be less than 15mm. One of the cable exits
has M22 screw thread and can work with the default combination cable to remove the risk of the
dragging and pulling of the cable.
The device has two waterproof airproof plugs (One default position is the cable exit of the chassis of
the device and the other is in the accessories bag.). The waterproof airproof plug has two functions.
One is to fill in the cable exit and pull through the cable. It supports the cable whose diameter ranges
from 4.0~6.0. It is very convenient for you to do the waterproof work when you pull the cable through
your own exit. Please refer to the steps listed.
Step 1
Take the waterproof airproof plug out, pull the cable (diameter ranges from 4.0 to 6.0) through the
waterproof airproof plug. See Figure 2-11.
Figure 2-11
Step 2
Before you go to the Step 4 in the chapter 2.2.1 installation steps, please pull through cable with the
waterproof airproof plug to the device chassis via the installation hole at the bottom of the chassis and
then connect the cable pins.
Step 3
Refer to Step 4 and Step 5 in the chapter 2.2.1 installation steps to install and connect the cable pin to
the device and then follow the proper steps to go on the installation.
Important
This series product has the power connection pin and I/O connection pin for you to pull
through the signal cable.
2.2.5 Installation Steps for Devices of Following Product Models: HDBW8351E,
HDBW8356E.