Daikin DM92SS User manual
INSTALLATION INSTRUCTIONS
IOD-2010O
08/2021
©2014-2019, 2021
www.daikincomfort.com
embodied in the American National
Standard / National Standard of Canada
Installer:
Ax all manuals
adjacent to the unit.
Remember, it is your responsibility to install the product
The precautions listed in this Installation Manual are intended
3
4
5
5
5
6
7
8
............
10
10
10
10
11
11
11
11
11
................ 11
11
13
13
.............................14
2
14
14
15
15
16
17
17
17
18
18
.....................................................
..........................................
30
30
31
31
31
31
31
31
31
33
33
33
33
34
34
35
35
35
35
35
35
36
36
36
36
36
36
36
36
36
36
36
37
37
37
37
37
37
37
37
38
38
38
38
38
38
38
41
43
44
installing, adjusting, altering, servicing, or operating the
in
and of this
Provide adequate combustion and ventilation air to the
Connect this furnace to an approved vent system only, as
in
air circulated by the furnace to areas outside the space
containing the furnace, the return air shall also be handled
by duct(s) sealed to the furnace casing and terminating
of
This furnace may be used as a construction site heater only
the
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warnings exactly could result
in serious injury, death or property damage.
Never test for gas leaks with an open flame.
Use a commercially available soap solution made
specifically for the detection of leaks to check all
connections. A fire or explosion may result causing
property damage, personal injury or loss of life.
RISQUE D'INCENDIE OU D'EXPLOSION
Si les consignes de sécurité ne sont pas suivies à la lettre,
cela peut entraîner la mort, de graves blessures ou des
dommages matériels.
Ne jamais vérifier la présence de fuites de gaz au moyen
d'une flamme nue. Vérifier tous les raccords en utilisant
une solution savonneuse commerciale conçue
spécialement pour la détection de fuites. Un incendie ou
une explosion risque de se produire, ce qui peut entraîner
la mort, des blessures ou des dommages matériels.
4
B10259-216
CO can cause serious illness including permanent brain
damage or death.
Advertencia especial para la instalación de calentadores ó manejadoras
de aire en áreas cerradas como estacionamientos ó cuartos de servicio.
B10259-216
El monóxido de carbono puede causar enfermedades severas
como daño cerebral permanente ó muerte.
Las emisiones de monóxido de carbono pueden circular a través
del aparato cuando se opera en cualquier modo.
B10259-216
RISQUE D'EMPOISONNEMENT AU MONOXYDE DE CARBONE
Cette ventilation est nécessaire pour éviter le danger d'intoxication
au CO pouvant survenir si un appareil produisant du monoxyde
de carbone continue de fonctionner au sein de la zone confinée.
All units are securely packed in shipping containers
tested according to International Safe Transit Association
The furnace must be carefully inspected on arrival for
Make a notation on delivery receipt of any visible
5
•
•
•
•
representative at the time damage is reported to
• The carrier is responsible for making prompt
inspection of damage and for a thorough
and servicing to protect the integrated control module from
Service integrated control module or connecting
Discharge your body to ground before removing a
proper electrical connections, circulating air temperature rise,
This furnace is primarily designed for residential home-
• It must be installed per the installation instructions
• It must be installed indoors in a building constructed
• It must be part of a ducted system and not used in a
•
•
•
( If using propane, a propane conversion kit is
Non-direct vent (single pipe) central forced air furnace
area or from air ducted from the outside or,
6
Direct vent (dual pipe) central forced air furnace in
burners through a special air intake system outlined
or propane gas ( If using propane, a propane
This furnace may be used as a construction site heater only
• The vent system is permanently installed per these
•
CANNOT be used and can cause long term
• Return air ducts are provided and sealed to the
•
•
the system and inspected daily and replaced as
needed during construction and upon completion of
• The input rate and temperature rise are set per the
•
using 100% outside air for combustion during
•
• All furnace operating conditions (including ignition,
•
•
•
•
•
to and the service area around the unit must have
American National Standards Institute
CSA International
8501 East Pleasant Valley
The rated heating capacity of the furnace should be greater
The total heat loss should be calculated by an approved
J-Load Calculations” published by the Air Conditioning
CSA International
provided in the Combustion and Ventilation Air Requirements
•
• Ensure the temperature of the return air entering the
• Provide provisions for venting combustion products
• Refer to Vent/Flue Pipe and Combustion Air Pipe
-Termination Locations for appropriate termination
locations and to determine if the piping system from
or combustion air piping can be a limiting factor in the
•
condensate drainage system in any area subject to
Condensate Drain Lines and Trap
• Ensure adequate combustion air is available for
Combustion and Ventilation Air Requirements.
•
Applications and Considerations for leveling of
•
• A special accessory subbase must be used for upright
A subbase
•
chlorine-based
carbon tetrachloride
deicing salts or chemicals
halogen type refrigerants
printing inks
cleaning solutions (such as perchloroethylene)
paint removers
varnishes
hydrochloric acid
cements and glues
antistatic fabric softeners for clothes dryers
• non-direct vent furnace if it is installed
near an area frequently contaminated by any of the
non-direct vent
the enclosed non-direct vent furnace has an adequate
supply of combustion air, vent from a nearby
Combustion and Ventilation Air Requirements for
•
•
•
• If the furnace is installed in a residential garage,
position the furnace so that the burners and ignition
• If the furnace is installed horizontally, ensure the
•
serves a separate appliance designed to burn solid
•
•
ensure the surface around the opening is smooth
•
necessary, use an accessory subbase (see
Do not install the furnace directly on carpeting, tile, or
(
8
installation codes, the requirements of the gas
•
•
•
necessitate greater clearances than the minimum
• In all cases, accessibility clearance must take
precedence over clearances from the enclosure
Installations must adhere to the clearances to combustible
The minimum clearance information for this furnace is
Refer to Vent/Flue Pipe and Combustion Air Pipe
In addition to the required clearances to combustible
materials, a minimum of 24 inches service clearance must
Sheet applicable to your model for minimum clearances to
door frame is usually adequate to satisfy this ventilation
system serving other appliances, the venting system may be
POSITION* SIDES REAR FRONT BOTTOM FLUE TOP
Upflow 0" 0" 3" C0" 1"
Horizontal 6" 0" 3" C0" 6"
C = If placed on combustible floor, floor MUST be wood only.
DM 92SS* M INIM UM CLEARANCES TO COM BUSTIBLE MATERIALS
(INCHES)
CARBON MONOXIDE POISONING HAZARD
Failure to follow the steps outlined below for each
appliance connected to the venting system being placed
into operation could result in carbon monoxide poisoning
or death.
The following steps shall be followed with each appliance
connected to the venting system placed in operation,
while any other appliances connected to the venting
system are not in operation:
1. Seal any unused openings in the venting system.
2. Inspect the venting system for proper size and
horizontal pitch, as required by the National Fuel Gas
Code, ANSI Z223.1 or the Natural Gas and Propane
Installation Code, CSA B149.1-15 and these
instructions. Determine that there is no blockage or
restriction, leakage, corrosion and other deficiencies
which could cause an unsafe condition.
3. As far as practical, close all building doors and
windows and all doors between the space in which
the appliance(s) connected to the venting system are
located and other spaces of the building.
4. Close fireplace dampers.
5. Turn on clothes dryers and any appliance not
connected to the venting system. Turn on any
exhaust fans, such as range hoods and bathroom
exhausts, so they shall operate at maximum speed.
Donot operate a summerexhaust fan.
6. Follow the lighting instructions. Place the appliance
being inspected in operation. Adjust thermostat so
appliance shall operate continuously.
7. Test for spillage from draft hood appliances at the
draft hood relief opening after 5 minutes of main
burner operation. Use the flame of a match or
candle.
8. If improper venting is observed during any of the
above tests, the venting system must be corrected in
accordance with the National Fuel Gas Code ANSI
Z223.1/NFPA 54 and/or National Gas and Propane
Installation Code CSA B149.1-15.
9. After it has been determined that each appliance
connected to the venting system properly vents
when tested as outlined above, return doors,
windows, exhaust fans, fireplace dampers and any
other gas burning appliance to their previous
conditions of use.
9
RISQUE D'INTOXICATION AU MONOXYDE DE CARBONE
Si les étapes décrites ci-dessous ne sont pas suivies pour
chacun des appareils raccordés au système de ventilation
au moment de sa mise en marche, cela peut entraîner une
intoxication au monoxyde de carbone ou la mort. Les
étapes suivantes doivent être suivies pour chacun des
appareils raccordés au système de ventilation au moment
de sa mise en marche, alors que tous les autres appareils
raccordés au système de ventilation ne sont pas en
marche :
1) Sceller toutes les ouvertures inutilisées du système de
ventilation.
2) Inspecter le système de ventilation afin de vérifier si la
taille et l'inclinaison par rapport à l'horizontale sont
conformes aux exigences du National Fuel Gas Code, ANSI
Z223.1/NFPA 54 ou du Code d'installation du gaz naturel
et du propane, CSA B149.1 et à ces instructions. Vérifier
qu'il n'y a pas d'obstruction ou de restriction, de fuite, de
corrosion et d'autres problèmes qui pourraient entraîner
une situation dangereuse.
3) Si possible, fermer toutes les portes et fenêtres du
bâtiment ainsi que toutes les portes séparant l'endroit où
se trouvent les appareils raccordés au système de
ventilation et les autres zones du bâtiment.
4) Fermer le registre des foyers.
5) Mettre les sécheuses en marche ainsi que tous les
autres appareils qui ne sont pas raccordés au système de
ventilation. Mettre en marche tous les ventilateurs de
tirage, comme celui des hottes de cuisine et des salles de
bains, et les régler à la puissance maximale. Ne pas mettre
en marche les ventilateurs d'été.
6) Suivre les instructions d'allumage. Mettre en marche
l'appareil soumis à l'inspection. Régler le thermostat de
manière à ce que l'appareil fonctionne en continu.
7) Vérifier la présence de fuite au niveau de l'ouverture du
coupe-tirage des appareils qui en sont dotés après 5
minutes de fonctionnement du brûleur principal. Utiliser
la flamme d'une allumette ou d'une bougie.
8) Si un problème de ventilation est observé pendant l'un
des essais décrits ci-dessus, des correctifs doivent être
apportés au système de ventilation conformément au
National Fuel Gas Code, ANSI Z223.1/NFPA 54 et (ou) au
Code d'installation du gaz naturel et du propane, CSA
B149.1.
9) Une fois qu'il a été déterminé que chaque appareil
raccordé au système de ventilation fonctionne
correctement au moyen des essais décrits ci-dessus, les
portes, les fenêtres, les ventilateurs, les registres de foyer
et tous les autres appareils de combustion alimentés au
gaz doivent être remis dans leur état initial.
• Drafts, or dead spots behind doors, in corners, or
•
•
•
•
•
TOP
TOP
• Unconditioned areas behind the thermostat, such as
Improved construction and additional insulation in buildings
helped in reducing heating/cooling costs but have created
a problem supplying combustion and ventilation air for gas
building occupants to gas combustion products that could
10
is an adequate supply of combustion and ventilation air
of the local building codes for determining the combustion
area by means of ventilation grilles or ducts connecting
directly to the outdoors or spaces open to the outdoors such
This furnace may be installed in an upright position or
IRON
PLACES
)
XX
11
In horizontal applications the condensate drain trap is
Condensate Drain Trap
and Line
adequate measures must be taken to prevent condensate
Leveling ensures proper condensate drainage from the heat
applications the connections can be made either through
A drain pan must be provided if the furnace is installed above
Refer to Horizontal Applications and Conditions - Drain Trap
and Lines.
Stage
Stage
Natural None
#45 None
Propane
1
None
Altitude
Kit
Orifice
Manifold Pressure
Pressure
Change
1
to compensate for the natural reduction in the density of
Contact the distributor for a tabular listing of appropriate
almost all of the heat from the products of combustion and
an approved vent pipe material, but it is permissible to use
12
are also approved vent and combustion air materials for
or vent connector, and must not be vented into any portion
commercially available “no hub connectors” other than those
installer to ensure that all piping and connections possess
section for details concerning piping size, length, number of
Requirement does not apply to the combustion air
As an alternative to PVC pipe, primer, solvent cement, and
the center line of the other opening for 2” diameter pipe, and
Adhere to these instructions to ensure safe and proper
TRANSITION NO LESS
NO TRANSITION ON
Piping must be adequately secured and supported to
prohibit sagging, joint separation, and/or detachment from
Precautions should be taken to prevent condensate from
Refer to Location Requirements and Considerations
Refer to Non-Direct Vent (Single Pipe) Piping and Direct
Vent (Dual Pipe) Piping
•
least 12 inches above ground level or the anticipated
• Vent terminations (non-direct and direct vent) must
This provision does not apply to the
combustion air intake termination of a direct vent
• The vent termination of a non-direct vent application
• The vent termination of a direct vent application must
terminate at least 12 inches from any opening through
• The vent termination of vent pipe run vertically
through a roof must terminate at least 12 inches
• A vent termination shall not terminate over public
vapor could create a nuisance or hazard or could
be detrimental to the operation of regulators, relief
• The combustion air intake termination of a direct vent
15 takes precedence over the preceding termination
Non-Direct Vent
No Terminations
min.
4'
min.
Non-Direct Vent
Direct Vent
<10'
Inlet
Non-Direct Vent
Direct Vent
Anticipated
All installations in Canada must conform to the requirements
14
under this standard, that the vent system be checked once
the authority having jurisdiction (gas inspection authority,
*IPEX
System 636™ is a trademark of IPEX Inc
It is the responsibility of the installer to ensure that the
piping connections to the furnace are secure, airtight, and
in the furnace socket and a rubber coupling installed to
refrigerant lines, metering devices, condensate drain
non-direct vent installations, a minimum of one
On upow units secure the combustion air intake pipe to
the air intake coupling by using a take apart rubber coupling
counterow units secure the
combustion air intake pipe to the air intake coupling using
15
coupling can be secured directly to the furnace intake
trapped drain tube free-draining to proper condensate
VENT-DRAIN
combustion air intake “coupling” to guard against inadvertent
In the horizontal left installation position, a means
of condensate collection must be provided to keep vent
M ODEL
PIPE
SIZE
1234567 8
275 70 65 60 55 50 45 40
3114 107 100 93 86 79 72 65
2145 140 135 130 125 120 115 110
3168 161 154 147 140 133 126 119
255 50 45 40 35 30 25 20
3127 120 113 106 99 92 85 78
2^30 25 20 15 10 5N/A N/A
3^72 65 58 51 44 37 30 23
2^30 25 20 15 10 5N/A N/A
3^72 65 58 51 44 37 30 23
2^40 35 30 25 20 15 10 5
372 65 58 51 44 37 30 23
260 55 50 45 40 35 30 25
3168 161 154 147 140 133 126 119
230 25 20 15 10 5N/A N/A
3113 106 99 92 85 78 71 64
2N/A N/A N/A N/A N/A N/A N/A N/A
365 58 51 44 37 30 23 16
2100 95 90 85 80 75 70 65
3137 130 123 116 109 102 95 88
260 55 50 45 40 35 30 25
3127 120 113 106 99 92 85 78
235 30 25 20 15 10 5N/A
3160 153 146 139 132 125 118 111
2N/A N/A N/A N/A N/A N/A N/A N/A
3127 120 113 106 99 92 85 78
DC92SS0804CN
DC92SS1005CN
DM92SS0805CN
DM92SS1004CN
DM92SS1005CN
DM92SS1205DN
DC92SS0402BN
DC92SS0603BN
DM92SS* / DC92SS* Direct Vent (2-Pipe) & Non-Direct Vent (1-Pipe)
(6)
Maximum Allowable Length of Vent/FLue Pipe & Combustion Air Pipe (Ft)
(1) (2)
ELBOWS
DM92SS0403AN
DM92SS0603BN
DM92SS0803BN
DM92SS0804CN
DM92SS0402BN
7,000 ft altitude or above use 3" pipe
^ DM92SS0803BN - add 10' of 2" pipe for up flow position, add 66' of 3" pipe for up flow position
^ DM92SS0805CN - add 15' of 2" pipe fpr upflow position, add 58' of 3" pipe for upflow position
^
DM92SS0804CN - add 25' of 2" pipe for up flow position, add 58' of 3" pipe for up flow position
1) Maximum allowable limits listed on individual lengths for inlet and flue and NOT a combination.
2) Minimum requirement for each vent pipe is five (5) feet in length and one elbow/tee.
3) Tee used in the vent/flue termination must be included when determining the number of
elbows in the piping system.
4) 2 1/2" or 3" diameter pipe can be used in place of 2" diameter pipe.
5) Increased Clearance Configurations using (2) 45 deg. Long Sweep elbows should be
considered equivalent to one 90 deg. elbow
16
Vent Pipe
Use alternate vent
& combination
air locations
Combustion Air Pipe
Field Supplied
Drain Tee on Vent Pipe
Condensate trapped
to prevent flue gas from escaping
and routed to field supplied
condensate disposal
1/4” per foot min.
slope to furnace
6’ Max.
Floor
Basement/Crawlspace
DOWN VENTING UPFLOW MODEL FURNACES ONLY
All piping and fittings must be joined per material manufacturers specifications
to prevent separation and flue gas leaks.
Insert flange. Cut 2 ½” long.
R 000142F
T
Drill a pilot hole at the cabinet dimple (size dictated by
Although non-direct vent installations do not require a
an upright installation uses the standard intake location, or a
venting)
Refer to the Direct and Non-Direct Vent Table for applicable
secured to the combustion air intake to prevent inadvertent
Vent/Flue Pipe and Combustion Air
Pipe - Termination Locations for details concerning location
6X.3IN.
IN
12” MIN
INTAKE AND VENT
or
Vent/Flue Pipe and Combustion
Air Pipe
prohibit damage to piping connections, a coupling should
18
Direct vent installations require both a combustion air intake
Vent/Flue and Combustion Air Pipe
- Termination Locations or Concentric Vent Termination
concerning connection of pipes to the furnace, refer to the
Vent/Flue Pipe and Combustion Pipe - Standard Furnace
Connections or Alternate Furnace Connections
combustion air intake pipe systems of a direct vent
If the combustion air intake pipe is to be installed above a
19
vertically, as through a roof, or horizontally, as through an
Vent/Flue Pipe and Combustion
Pipe - Termination Locations for details concerning location
If more than one direct vent furnace is to be installed
vertically through a common roof top, maintain the same
If more than one direct vent furnace is to be installed
Refer to the directions provided with the Concentric Vent Kit
(DCVK) for installation specications.
vent kit must terminate outside the structure and may be
Vertical Installation
must be collected in the furnace drain trap and routed to
concerning furnace drain trap installation and drain hose
•
•
•
•
• Do not trap the drain line in any other location than at
•
must be taken to prevent condensate from freezing
•
installed in the drain line, near the cooling coil, to
In vertical installations, air conditioning coil
condensate may drain into the furnace trap as long as there
20
#
#1 #2
#4
#5
#6
#8
#9
#10
#11
100 Degree
Elbow
Coupling
Figure 21
NOTE: Drain components shown for information purposes only.
NOTE: Drain components shown for information purposes
only.
Drain the furnace and air conditioning coil if applicable,
furnace drain, it must be vented by an open tee installed at a
to prevent air conditioning condensate from backing up into
from the outside of the cabinet (barbed end goes
in the cabinet) through hole in the right side of the
Install the 45 degree pipe / hose drain coupling from
the outside of the cabinet (barbed end goes in the
cabinet) through the hole in the left side of the cabinet
This manual suits for next models
1
Table of contents
Other Daikin Furnace manuals
Daikin
Daikin 90 Plus AFUE Guide
Daikin
Daikin DC96VE User manual
Daikin
Daikin DM92SN Operating instructions
Daikin
Daikin DM96VE User manual
Daikin
Daikin DM80SE Operating instructions
Daikin
Daikin DM80SN Operating instructions
Daikin
Daikin DM80HS User manual
Daikin
Daikin DM97MC Operating instructions
Daikin
Daikin DM80SE Operating instructions
Daikin
Daikin DM92SE Operating instructions
Daikin
Daikin DM96SN User manual
Daikin
Daikin DM80VC Operating instructions
Daikin
Daikin DM96SE User manual
Daikin
Daikin DM80VC User manual
Daikin
Daikin DM96SE User manual
Daikin
Daikin DC97MC User manual
Daikin
Daikin DM80HS0403A User manual
Daikin
Daikin FC Series Instruction Manual
Daikin
Daikin DM80TN Operating instructions
Daikin
Daikin DC96SN User manual
Popular Furnace manuals by other brands
Jelrus
Jelrus Infinity M-30 Operator's manual
Crown
Crown CSHB60-90ABP Installation, operation and service manual
Amana
Amana xMVM97 series installation instructions
Winchester
Winchester WOL Series Installation, operation and maintenance instructions
Lennox
Lennox EL195UHE Elite Series installation instructions
Rheem
Rheem GRC Series installation instructions
Bard
Bard WG3S2-A installation instructions
Bryant
Bryant EVOLUTION 577D User's information manual
Coleman
Coleman UGAA075BUJ installation manual
US Stove Company
US Stove Company 8500 owner's manual
VERDER
VERDER CARBOLITE GERO CRF/1 Installation, operation and maintenance instructions
Lennox
Lennox ML195UH 045XP24B Unit information
Newmac
Newmac WAO E Installation, operating and service manual
Carrier
Carrier KGALB0101KIT installation instructions
KEER
KEER ECLIPSE MAX Installation, operation and maintenance manual
Lennox
Lennox G43UF SERIES Unit information
Carrier
Carrier 58MSA Series instruction manual
Carrier
Carrier 58CVA Installation, start-up, operating and service and maintenance instructions