Daintree GE Current Lumination Tetra Contour 62189... User manual

Installation Guide
ARCH048
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING / AVERTISSEMENT
Risk of electrical shock. Disconnect power before
servicing or installing product.
Risque de choc électrique. Couper l’alimentation
avant le dépannage ou avant l’installation du produit.
Lumination®LED Luminaire
Product Code: 62189
Description Code: GE180/MV/V24T1-C
(Tetra®Contour)
Prepare Electrical WiringLED Driver Features
• Class 2 wiring per NEC Article 725 (SELV)
• IP54: Dry or damp location rated
Electrical Requirements
• The LED driver must be supplied with 100-277 VAC,
50/60 Hz and connected to an individual properly
grounded branch circuit, protected by a 15 or 20
ampere circuit breaker.
Grounding Instructions
• The grounding and bonding of the overall system
shall be done in accordance with National Electric
Code (NEC) Article 600 and local codes.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class
[A] RFLD complies with the Canadian standard ICES-003. Ce DEFR de la classe [ A ] est conforme á la NMB-003 du Canada.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own expense.

www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
ARCH048 (Rev 04/02/2021)
Lumination®(Tetra® Contour) Installation Guide
This product is intended to be used as a lamp control gear that is installed after the mains control switch.
Conforms to the following standards:
LED Driver Installation
To LED system
Output wires
Green with
yellow
stripe
(ground)
AC line
White (neutral) Black (line)
To LED system
Output wires
Green with
yellow
stripe
(ground)
AC line
White (neutral) Black (line)
To LED system
Output wires
Green with
yellow
stripe
(ground)
AC line
White (neutral) Black (line)
Min Typical Max
Input Voltage (VAC) 90 100-277 305
Input Frequency (Hz) - 50/60 -
Input Current (A) 0.7 - 2.5
Output Voltage (VDC) 23.25 24.0 24.75
Output Current (ADC) - - 3.8
Output Power (W) - - 180
Environmental Operating Temperature Range -40°C +25°C +60°C
Environmental Humidity (non-condensing) 0% - 90%
Environmental Storage Temperature Range -40°C - +85°C
Enclosure Specication IP54: Dry or damp location rated
Dimensions 15.5 in. x 2.5 in. x 1.6 in. (392 mm x 62 mm x 40 mm)
Mount LED driver and remove
junction box cover. Carefully
remove knockout for AC line
input wires. Install appropriate
electrical ttings in the knockout
holes for wire protection.
1
Connect the supply wire
that is attached to your LED
system to the red (+) and
black (-) output wires of the
LED driver as outlined in the
“Electrical Connections”
section of your LED system’s
Installation Instructions.
2
Connect the AC line to the black
(line) and white (neutral) input
wires of the LED driver using
18-14 AWG (0.82-2.08 mm2)
twist-on wire connectors.
Ground LED driver by connecting
green wire with yellow stripe
to grounding screw. Replace
junction box cover.
3
Technical Specications
Note: For remote mounting or loading information refer to the LED System Installation Instructions.