POWER VERSION
Daisy Power install Document 10/4/22
1. Decide what end you want the Daisy Power control housing and tube motor. To mount the tube motor in the
tube: On the roller end you want the control housing and tube motor, wrap the paper template around roller tube.
Note the arrows indicating the end of the tube and the arrows that match together when the template is around the
tube. This will ensure the template is square for correct tube motor installation
2. Without the drive motor inside the tube, mark, and drill 6 x 4.5mm holes through the template with the 4.5mm
drill bit (there are 3 holes to be drilled around the tube 8mm in from the end of the tube and a further 3 holes to be
drilled around the tube approximately 285mm from end of tube)
3. Insert the drive motor into the tube, making sure the drive motor is pushed all the way in so the disengage system
works correctly. If there is a feather plug in way, remove, cut the tip of the feather plug off (so it does not hit the
tube motor), then replace after motor install, then using the 4.5mm drill again, drill through the 6 holes in the tube,
through the drive motor flange. Note: drive motor may have holes already in flange, ensure these holes are not near
the mounting holes
4. Insert and tighten the 6 x mounting screws. Important: make sure screws around end of tube do not interfere with
tube motor (don’t touch tube motor) – check by disengaging drive to freewheel (pulling pin out –see To Disengage
Drive in operation section)
1.
Daisy Power install Document 10/4/22
1. Decide what end you want the Daisy Power control housing and tube motor. To mount the tube motor in the
tube: On the roller end you want the control housing and tube motor, wrap the paper template around roller tube.
Note the arrows indicating the end of the tube and the arrows that match together when the template is around the
tube. This will ensure the template is square for correct tube motor installation
2. Without the drive motor inside the tube, mark, and drill 6 x 4.5mm holes through the template with the 4.5mm
drill bit (there are 3 holes to be drilled around the tube 8mm in from the end of the tube and a further 3 holes to be
drilled around the tube approximately 285mm from end of tube)
3. Insert the drive motor into the tube, making sure the drive motor is pushed all the way in so the disengage system
works correctly. If there is a feather plug in way, remove, cut the tip of the feather plug off (so it does not hit the
tube motor), then replace after motor install, then using the 4.5mm drill again, drill through the 6 holes in the tube,
through the drive motor flange. Note: drive motor may have holes already in flange, ensure these holes are not near
the mounting holes
4. Insert and tighten the 6 x mounting screws. Important: make sure screws around end of tube do not interfere with
tube motor (don’t touch tube motor) – check by disengaging drive to freewheel (pulling pin out –see To Disengage
Drive in operation section)
2. ˚TtcT
Daisy Power install Document 10/4/22
1. Decide what end you want the Daisy Power control housing and tube motor. To mount the tube motor in the
tube: On the roller end you want the control housing and tube motor, wrap the paper template around roller tube.
Note the arrows indicating the end of the tube and the arrows that match together when the template is around the
tube. This will ensure the template is square for correct tube motor installation
2. Without the drive motor inside the tube, mark, and drill 6 x 4.5mm holes through the template with the 4.5mm
drill bit (there are 3 holes to be drilled around the tube 8mm in from the end of the tube and a further 3 holes to be
drilled around the tube approximately 285mm from end of tube)
3. Insert the drive motor into the tube, making sure the drive motor is pushed all the way in so the disengage system
works correctly. If there is a feather plug in way, remove, cut the tip of the feather plug off (so it does not hit the
tube motor), then replace after motor install, then using the 4.5mm drill again, drill through the 6 holes in the tube,
through the drive motor flange. Note: drive motor may have holes already in flange, ensure these holes are not near
the mounting holes
4. Insert and tighten the 6 x mounting screws. Important: make sure screws around end of tube do not interfere with
tube motor (don’t touch tube motor) – check by disengaging drive to freewheel (pulling pin out –see To Disengage
Drive in operation section)
4.
5.
3.
Note:
