Dakota Digital BIM-01-2-HLLY User manual

[1] MAN #650588D
BIM-01-2-HLLY
Bus Interface Module for Holley EFI
This Bus Interface Module is designed to read engine information from specific Holley EFI kits. The Holley Terminator,
HP, Sniper, Dominator and Terminator X and X Max. The module is connected to the Holley EFI through the CAN-bus
plug on the EFI harness. Depending on your EFI module you may have a 2-pin or 4-pin CAN connector. We supply EFI
adapter harnesses that will allow you to connect with your particular kit.
There are two interface (I/O) ports on the BIM-01-2-HLLYmodule. Either one can be connected to the instrument system
or to another module, allowing several units to be daisy chained together.
Cannot daisy chain with GPS-50-2.
Do not connect the I/O port to anything other than a Dakota Digital control box or BIM.
Do not mount the module in the engine compartment; as it should be mounted in the vehicle’s cabin.
The engine and transmission information that is available from the unit depends on the EFI kit and module programming
and add-ons. For specific data readings: see individual setups below for each version of Holley EFI system below.

[2] MAN #650588D
Table of Contents
Holley EFI Setup
Page 2
Display Setup Overview - VFD3 / VFD3X Setup
Page 4
VHX Setup
Page 6
HDX / RTX Setup
Page 8
BIM Setup Menu
Page 9
Quick Tips and Trouble Shooting
Page 11
Warranty
Page 12
Holley Terminator, HP and Dominator EFI system setup:
For this to unit to function correctly with the Holley Terminator, HP and Dominator systems, you will need to ensure the
Holley CAN settings are set to “Racepak.” These settings are adjusted through Holley’s PC or MAC computer software.
To make this change select:
1. ‘System ICF’ tab along the top icon menu.
2. Then select ’Basic I/O’ on left menu.
3. Then select ’CAN Bus’ button on the right to show ’CAN Bus 1 Type’ and ‘CAN Bus 2 Type’.
4. Select the dropdown and select “Racepak”.
oTerminator or HP ECU –Both 1 and 2 must be set to ‘Racepack’
oDominator ECU –change 1 or 2 to ‘Racepack’ and connect BIM cable to that CAN 1 or 2 cable
Terminator, HP and Dominator EFI speed input:
Data that should be available: RPM, Engine temp, Intake/manifold temp, MAP/boost, A/F ratio.
Data that is kit and add-on dependent: Vehicle speed, Oil pressure, Fuel pressure.
This module is programmed to monitor speed broadcasted from Dominator and Terminator/HP ECU’s.
By default, it is pre-programmed to monitor the Dominator ECU speed input (J4 pin B18).
It’s also capable of monitoring Terminator / HP and Dominator Input #1 (J1A pin A12) for speed (F).
To enable Input for speed monitoring,
For the BIM-01-2-HLLY, to read speed, please verify the following:
1. The Holley ECU must be wired and configured within the Holley computer software to read vehicle speed
a. If speed sensor is connected to Input #1, the BIM-01-2-HLLY must have the speed input enabled
Holley ECU speed input wiring:
•Vehicle speed must be wired to:
oDominator ECU: Input #39 on J4, pin B18
oTerminator/HP ECU: Input #1 on J1A, pin A12 (alternate option for Dominator).

[3] MAN #650588D
Terminator, HP and Dominator EFI speed input setup, continued:
If speed sensor is connected to Input #1 on J1A, pin A12
•Using the Holley computer software, the Input #1 must be labeled as Speed.
•Ensure the Speed input is mapped to a frequency (F) Input Type on the Holley Pin Map.
•These settings will enable the Holley to send speed out on the Racepack CAN
To monitor Input #1 on J1A, pin A12 you must enable the  setting within the BIM:
•Hold button on BIM-01-2-HLLY and turn ignition on, then release the button.
•Tap button to display (Input).
•Hold button until a dash (–) is displayed, and then release.
•Tap the button to display 
•Hold button until a dash (–) is displayed, and then release.
•Tap button to display , then hold to save.
Sniper EFI system setup:
Data that should be available: RPM, Engine temp, Intake/manifold temp, MAP/boost, A/F ratio.
Holley system setup: No configuration within the Sniper EFI system or software is required.
BIM-01-2-HLLY setup: The BIM must be configured to understand it will be talking to the Sniper EFI
•Hold button on BIM-01-2-HLLY and turn ignition on, then release the button.
•Tap button to display  (System).
•Hold button until a dash (–) is displayed, and then release.
•Tap the button to display (Sniper)
•Hold button until a dash (–) is displayed, and then release.
•Tap button to display , then hold to save.
Note: Speed Input is not a selectable menu option with  selection –Sniper does not send speed.
Terminator X, X Max EFI system setup:
Data that should be available: RPM, Engine temp, Intake/manifold temp, Boost only, A/F ratio, Oil pressure,
Fuel pressure.
Terminator X Max: Reads everything as the Terminator X, plus Vehicle speed.
Holley system setup: No configuration within the Sniper EFI system or software is required.
BIM-01-2-HLLY setup: The BIM must be configured to understand it will be talking to the Terminator X, X Max.
•Hold button on BIM-01-2-HLLY and turn ignition on, then release the button.
•Tap button to display  (System).
•Hold button until a dash (–) is displayed, and then release.
•Tap the button to display (Terminator X)
•Hold button until a dash (–) is displayed, and then release.
•Tap button to display , then hold to save.
EFI MAP/boost:
This module is programmed to monitor MAP(PSI/inHg) and boost (PSI/inHg) data broadcasted on the Holley EFI. MAP
and boost will both be displayed with the boost label on our system. MAP is the default reading preset from the factory. If
you wish to monitor boost pressure you must enable the  (boost) option through the setup menu. Please see setup
steps on page 10.
Note: Terminator X will not show MAP, only boost PSI readings. Speed input is not a selectable menu option with 
selection.

[4] MAN #650588D
Display Setup
VFD and VHX system will add extra readings to the message displays under the tach.
HDX and RTX need a group screen configured to show additional information, as Boost or Intake temp
Setting up the display system will configure the instrument control box to read each input from either the terminals or
through the BIM cable from the Bus Interface Module.
The BIM menu of the display will not find the BIM-01-2-HLLY, but will find specific channels for Fuel Pressure and Air/Fuel
Ratio.
There is no Check Engine option for the BIM-01-2-HLLY to pick up.
The following settings are for the basic information to be displayed with data from the BIM module.
Extra data that might be sent such as Intake Air Temp, Fuel Pressure, Air/Fuel Ratio or Boost, can be brought up in the
message centers of the VFD3 and VHX system by toggling SW2 in normal operation of the vehicle. Similar data that
might be present will not automatically be shown in the HDX and RTX systems. That extra information must be placed in
a group screen of your choice, in the HDX and RTX setup.
Display data usage
The following readings can each be used in place of dedicated sending units to the instrument system control box. These
are individually selectable in the display system instrument setup menus.
VFD3, and VFD3X setup:
**Only VFD3/3X systems with a plastic case, support adding BIMs**
Entering the VFD3 setup is done by holding SW1 (I) and turning the ignition to “on”, or “acc”.
Once in setup, one can move between speed, tach, volt, water, etc…. by tapping SW1 (I)
If you are setting multiple items, once done with one section you will automatically move onto the next item.
Obtaining speed from the BIM-01-2-HLLY
Dominator, HP, and Terminator X Max - Not Sniper, nor Terminator X
•Hold the SW1 switch from the instrument system control box while turning the key on.
oThe speed display will show  and the message display will show SETUP.
•Release SW1. The displays should show and SPEED, respectively.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The message display will show SENDER.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The speed display will show the current
setting.
•Tap SW1 until  and BUS are displayed.
•Press and hold SW1 until  and DONE are displayed.
oNOTE: The AUTO, auto calibration, is removed.
oSpeed can only be fine-tuned with the ADJUST mode at a standstill.
oADJUST now only alters the percentage of speed by +/- 25%.
▪Drive a known speed and calculate how far off the speed is in percentage.
•GPS speed / displayed speed x 100
•Sample - [60/50=1.2] [1.2x100 = 120] 120%
▪Enter setup and go to ADJUST, tap SW1 to increment from 100% up to 125%.
▪After 125% the values will fall back to 75% and increment up again.
▪When the desired percentage is reached, hold SW1 until  changes to “-”.
•Tap SW1 until  and DONE are displayed.
•Press and hold SW1 until “-”and DONE are display.

[5] MAN #650588D
VFD3, and VFD3X Setup Continued:
Obtaining RPM from the BIM-01-2-HLLY
•Hold the SW1 switch from the instrument system control box while turning the key on.
oThe speed display should show  and the message display should show SETUP.
•Release SW1. Tap SW1 until  and TACH are displayed.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The displays should show  and T CAL.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The speed display will show the current
setting.
•Tap SW1 until and T CAL are displayed.
•Press and hold SW1 until “-” and DONE are displayed.
•Tap SW1 until  and DONE are displayed.
•Press and hold SW1 until “-” and DONE are displayed.
Obtaining engine temperature from the BIM-01-2-HLLY
•Hold the SW1 switch from the instrument system control box while turning the key on.
oThe speed display should show  and the message display should show SETUP.
•Release SW1. Tap SW1 until  and WATER are displayed.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The displays should show  and SENDER.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The speed display will show the current
setting.
•Tap SW1 until  and BUS F (Fahrenheit) is displayed.
oTap SW1 once more for  and BUS C (Celsius) if desired.
•Press and hold SW1 until “-” and DONE are displayed.
•Tap SW1 until  and DONE are displayed.
•Press and hold SW1 until “-” and DONE are displayed.
Obtaining oil pressure from the BIM-01-2-HLLY (not Sniper, if available in HP/Dominator)
•Hold the SW1 switch from the instrument system control box while turning the key on.
oThe speed display should show  and the message display should show SETUP.
•Release SW1. Tap SW1 until  and OIL are displayed.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The displays should show  and SENDER.
•Press and hold SW1 for at least 3 seconds, until  changes to “-”. The speed display will show the current
setting.
•Tap SW1 until  and BUS are displayed.
•Press and hold SW1 until “-” and DONE are displayed.
•Tap SW1 until  and DONE are displayed.
•Press and hold SW1 until “-” and DONE are displayed.

[6] MAN #650588D
VHX Setup:
Entering the VHX setup is done by holding SW1 (I) and turning the ignition to “on”, or “acc”.
Once in setup, one can move between speed,tach,volt,water, etc…. by tapping SW1 (I)
If you are setting multiple items, once done with one section you will automatically move onto the next item.
Obtaining speed from the BIM-01-2-HLLY
Dominator, HP, and Terminator X Max - Not Sniper, nor Terminator X
•Hold the SW1 (I) switch from the instrument system control box while turning the key on.
oThe message display should show SETUP.
•Release SW1 (I) - LCD1 should show SETUP SPEED.
•Press and hold SW1 (I) for at least 3 seconds until SPEED SENDER is displayed.
•Press and hold SW1 (I) for at least 3 seconds until SENDER is displayed.
•Release the switch and SENDER NORMAL will be displayed.
•Tap SW1 (I) until SENDER BUS is displayed.
•Press and hold SW1 (I) until DONE is displayed.
oNOTE: The AUTO, auto calibration, is removed.
oSpeed can only be fine-tuned with the ADJUST mode at a standstill.
oADJUST now only alters the percentage of speed by +/- 25%.
▪Drive a known speed and calculate how far off the speed is in percentage.
•GPS speed / displayed speed x 100
•Sample - [60/50=1.2] [1.2x100 = 120] 120%
▪Enter setup and go to ADJUST, tap SW1 (I) to increment from 100% up to 125%.
▪After 125% the values will fall back to 75% and increment up again.
▪When the desired percentage is reached, hold SW1 (I) until DONE is displayed
•Tap SW1 (I) until SPEED DONE is displayed.
•Press and hold SW1 (I) until a big DONE is displayed.
Obtaining RPM from the BIM-01-2-HLLY
•Hold the SW1 (I) switch from the instrument system control box while turning the key on.
oThe message display should show SETUP.
•Release SW1 (I) - LCD1 should show SETUP SPEED.
•Tap SW1 (I) until SETUP TACH is displayed.
•Press and hold SW1 (I) for at least 3 seconds until TACH ENGINE is displayed.
•Press and hold SW1 (I) for at least 3 seconds until ENGINE is displayed.
•Release the switch and ENGINE 8 will be displayed.
•Tap SW1 (I) until ENGINE BUS is displayed.
•Press and hold SW1 (I) until DONE is displayed.
•Tap SW1 (I) until TACH DONE is displayed.
•Press and hold SW1 (I) until a big DONE is displayed.
Obtaining engine temperature from the BIM-01-2-HLLY
•Hold the SW1 (I) switch from the instrument system control box while turning the key on.
oThe message display should show SETUP.
•Release SW1 (I) - LCD1 should show SETUP SPEED.
•Tap SW1 (I) until SETUP WATER is displayed.
•Press and hold SW1 (I) for at least 3 seconds until WATER SENDER is displayed.
•Press and hold SW1 (I) for at least 3 seconds until SENDER DD F is displayed.
•Release the switch and SENDER DD F will be displayed.
•Tap SW1 (I) until SENDER BUS F (Fahrenheit) is displayed.
oTap SW1 (I) once more for SENDER BUS C (Celsius) if desired.
•Press and hold SW1 until DONE is displayed.
•Tap SW1 (I) until WATER DONE is displayed.
•Press and hold SW1 (I) until a big DONE is displayed.

[7] MAN #650588D
VHX Setup Continued:
Obtaining oil pressure from the BIM-01-2-HLLY (not Sniper, if available in HP/Dominator)
•Hold the SW1 (I) switch from the instrument system control box while turning the key on.
oThe message display should show SETUP.
•Release SW1 (I) - LCD1 should show SETUP SPEED.
•Tap SW1 until SETUP OIL is displayed.
•Press and hold SW1 (I) for at least 3 seconds until OIL SENDER is displayed.
•Press and hold SW1 (I) for at least 3 seconds until SENDER NORMAL is displayed.
•Release the switch and SENDER NORMAL will be displayed.
•Tap SW1 (I) until SENDER BUS is displayed.
•Press and hold SW1 (I) until DONE is displayed.
•Tap SW1 (I) until OIL DONE is displayed.
•Press and hold SW1 (I) until a big DONE is displayed.

[8] MAN #650588D
HDX and RTX setup:
**HDX/RTX systems can be configured with the Dakota Digital app for Apple and Android devices**
HDX and RTX Operations
•HDX: With the ignition key already on, press and hold both switches to enter SETUP, release when instructed.
oIf using the external rocker switch, hold SW2 (II) while turning the ignition on.
oRelease the switch when SETUP is shown.
oLeft switch on display is SW1, and right switch on display is SW2
•RTX: With the ignition off, press hold SW2 (II) while turning the ignition key on to enter SETUP
oRelease the switch when SETUP is shown.
•BOTH: When holding for an option, release the button when the screens says “RELEASE”
•BOTH: You may skip to whichever reading you’d like to configure below; they do not need to be done in order.
•BOTH: After making a selection, tap a switch and select BACK to save and return to the main menu, then select
EXIT SETUP to return to normal operation.
•BOTH: SWI (left) moves up ↑the menu list, SWII (right) moves down ↓the menu list
Obtaining speed from the BIM-01-2-HLLY
Dominator, HP, and Terminator X Max - Not Sniper, nor Terminator X
•Tap SWII (right) switch until SPEED is selected. Press and hold SWII (right) switch to enter SPEED menu.
•Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•SIGNAL will be is displayed. Press and hold SWII (right) switch to enter SIGNAL menu.
•Tap right switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•When SIGNAL is displayed again, tap switch until BACK is displayed, then hold to return to INPUT.
•When INPUT is displayed again, tap switch until BACK is displayed, then hold the switch to exit.
oNOTE: The AUTO CAL, auto calibration, is not accessible.
oADJUST now only alters the percentage of speed by +/- 25%.
▪After the engine is running, enter setup and go to ADJUST.
▪While driving a known speed, SWI and SWII (left/right) can adjust speed.
•Percentage can also be adjusted without driving.
▪Tap SWII (right) to increment up to 125%.
▪Tap SW1 (left) to decrement down to 75%.
▪The speed will be displayed in the LCD along with the percent chosen.
▪Once the speed is correct, hold either switches until RELEASE is displayed.
▪You may now continue to exit the setup menu.
oThe Dakota Digital Automotive app can also be used either while driving or not driving.
Obtaining RPM from the BIM-01-2-HLLY
•Tap SWII (right) switch until TACH is selected. Press and hold SWII (right) switch to enter TACH menu.
•Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•Tap SWII (right) switch until CYLINDER is displayed. Press and hold SWII (right) switch to select CYLINDER.
•Tap SWI (left) switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•When INPUT is displayed again, tap until BACK is displayed, then hold the switch to exit.
Obtaining engine temperature from the BIM-01-2-HLLY
•Tap SWII (right) switch until WATER is selected. Press and hold SWII (right) switch to enter WATER menu.
•Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•Tap SWII (right) switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•When INPUT is displayed again, tap until BACK is displayed, then hold the switch to exit.
Obtaining oil pressure from the BIM-01-2-HLLY (not Sniper, if available in HP/Dominator)
•Tap SWII (right) switch until OIL is selected. Press and hold SWII (right) switch to enter OIL menu.
•Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•Tap SWII (right) switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•When INPUT is displayed again, tap until BACK is displayed, then hold the switch to exit.

[9] MAN #650588D
BIM setup:
BIM menu table:
Menu
Options
Default
Notes








Check engine light sent by ECU *** Not used by HOLLEY












For Terminator HP and Dominator systems




For Sniper EFI




For Terminator X and Terminator X Max








Input 1 speed enable, only in menu when  is set to  (HP & Dominator)












Gauge will display MAP/vacuum reading *** Terminator X cannot read MAP




Gauge will display boost








Update communications with other BIM modules attached








Exit Setup.




System Selection for Holley module
The BIM-01-2-HLLY must be configured for the correct type of Holley EFI system being used.
•Hold the switch on the BIM-01-2-HLLY case while turning the key on. The BIM display will show the current
revision code while this is held.
•Release the switch.
•Tap the switch until the display shows  (system). Press and hold to enter this menu.
•When you see “” on the display release the switch.
•The display will show the current system , , or 
•Tap the switch to change the system.
o –Standard = Dominator or Terminator HP
o –Sniper
o –Terminator X only
•To save setting press and hold the switch until you see “” on the display, then release the switch.
•The display will show “”. Press and hold the switch to exit setup or tap to choose another menu option.
Enable or disable ability to read speed (HP and Dominator  = )
Not an option when  is set to  or 
With the configuration of the speed input in either the Dominator or Terminator HP, the BIM-01-2-HLLY has the option
•Hold the switch on the BIM-01-2-HLLY case while turning the key on. The BIM display will show the current
revision code while this is held.
•Release the switch.
•Tap the switch until the display shows  (input). Press and hold to enter this menu.
•When you see “” on the display release the switch.
•The display will show the current state or the speed input  (enable) or  (disable).
•Tap the switch to change the state.
•To save setting press and hold the switch until you see “” on the display, then release the switch.
•The display will show . Press and hold the switch to exit setup or tap to choose another menu option.

[10] MAN #650588D
BIM setup continued:
Enabling Boost:
All Holley systems (except for Terminator X) will always send MAP/vacuum data to the BIM-01-2-HLLY.
The BIM-01-2-HLLY has an option to enable boost readings if the car has turbocharger, and this works on all models of
Holley EFI systems.
•Hold the switch on the BIM-01-2-HLLY case while turning the key on. The BIM display will show the current
revision code while this is held.
•Release the switch.
•Tap the switch until the display shows  (boost). Press and hold to enter this menu.
•When you see “” on the display release the switch.
•The display will show the current boost state,  (disable) or  (enable).
•Tap the switch to change the state.
•To save setting press and hold the switch until you see “” on the display, then release the switch.
•The display will show . Press and hold the switch to exit setup or tap to choose another menu option.
To set or change the ID number:
The ID will not normally need to be changed. The fuel PSI and A/F ratio readings both use bus ID’s so if you have other
BIM units connected along with this one, there is a chance of ID conflicts. This can easily be resolved. If fuel PSI or A/F
ratio is not showing up in the BIM setup menu on your system you may need to resolve an ID conflict. The following
procedure will allow the BIM-01-2 to automatically select a new, unused ID.
•Hold the switch on BIM while turning the key on. The BIM will show the current software code.
•Release the switch.
•Press and release the switch until “” is shown on the display.
•Press and hold. “” will be shown while the BIM is scanning the bus for other BIM units.
•When you see “” shown on the display release the switch.
•The BIM unit will now go back to normal operation.
HDX/RTX TIP: Intake/manifold air temp, Fuel PSI, boost and A/F ratio will be displayed in the group screens if activated
through the displays>>group set menu setup.

[11] MAN #650588D
Quick tips:
While the BIM is operating, the dot in the upper left corner of the display will indicate the status. On steady indicates it is
powered up but not receiving any BIM bus activity. Flashing indicates it is communicating on the BIM bus.
If the display shows “” then it is scanning to try and communicate with the EFI system bus but cannot get an answer.
To see the sensor and channel status on the BIM display, press and hold the switch. The display will cycle through
several screens. The first will show the bus type (“” Holley EFI). The next screens will indicate which (if any) extended
data is available: “” for intake/manifold temp, “” for engine oil pressure.
Troubleshooting guide:
Problem
Possible cause
Solution
BIM will not light up at all
•PWR wire does not have power.
•Connect to a different ground location
•Power/data harness is damaged.
•Module is damaged.
•Connect to a location that has +12V key-on
power.
•Inspect harness and repair or replace.
•Return for service. (See Instructions below)
BIM display is scanning “”
•EFI adapter harness is not connected
•The EFI system is not compatible
•The EFI is not powered on.
•The EFI CAN is not configured to “Racepak”
•Connect the appropriate harness to the EFI
CAN.
•Verify compatibility.
•Verify EFI system is powered on.
•Verify CAN settings within EFI software.
•If connected to Dominator, HP or Terminator verify
 is set to  in the BIMs setup menu
BIM has a steady dot lit
•Interface cable is not connected
•Interface cable is loose.
•On VHX systems, the BIM display for this is
disabled.
•Connect the supplied data cable between the
BIM unit and the instrument system control box.
•Make sure both ends of the cable are seated.
•Follow instructions in VHX manual to enable
the BIM display screen.
BIM display shows “:”
•Data cable is damaged.
•Another module on the bus is damaged or
connected improperly.
•Inspect and replace the data cable.
•Inspect other modules on the bus.

[12] MAN #650588D
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical support is
available to help you work through any questions or problems you may be having installing one of our
products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems.
For additional support, please visit www.dakotadigital.com. A “Product Support” link will be found at the
bottom of the home page.
Should you ever need to send the unit back for repairs, please call our technical support line,
[phone], to request a Return Merchandise Authorization number.
•Package the product in a good quality box along with plenty of packing material.
•Ship the product by a common carrier with tracking abilities.
•Be sure to include the RMA number on the package.
•Include a complete description of the problem, with RMA number, your full name and address (street
address preferred), and a telephone number where you can be reached during the day.
•Any returns for warranty work must include a copy of the dated sales receipt from your place of
purchase.
•Send no money. We will contact you for payment.
Dakota Digital Limited Lifetime Warranty
DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and
condition, be proven defective in material or workmanship for the lifetime of the original vehicle it was installed in, such
defect(s) will be repaired or replaced at Dakota Digital’s option.
This warranty does not cover nor extend to damage to the vehicle’s systems, and does not cover diagnosis, removal or
reinstallation of the product.
This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged
through alteration, improper installation, mishandling, misuse, neglect, or accident.
Dakota Digital assumes no responsibility for loss of time, vehicle use, owner inconvenience nor related expenses.
Dakota Digital will cover the return standard freight once the product has been evaluated for warranty consideration,
however the incoming transportation is to be covered by the owner.
This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties, including any implied
warranty of merchantability, shall be limited to the duration of this written warranty. No person or representative is
authorized to assume, for Dakota Digital, any liability other than expressed herein in connection with the sale of this
product.
WARNING: This product can expose you to chemicals including lead, which is known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov