Daktronics BA-1518-11 User manual

All Sport®is a registered trademark of Daktronics, Inc.
Multi-Section Outdoor
LED Scoreboards
Installation, Maintenance,
and Specifications Manual
ED12562
National Electrical Code® is a registered trademark of NFPA International.
Scoreboard Models
BA-1518-11 FB-1424-11 FB-1630-11 FB-2001-11 SO-1424-11
BA-1524-11 FB-1430-11 FB-1630L-11 FB-2002-11 SO-1624-11
BA-2007-11 FB-1524-11 FB-1730-11 FB-2003-11 SO-1830-11
BA-3718-11 FB-1530-11 FB-1830-11 MS-2009-11 SO-1830L-11
BA-3724-11 FB-1624-11 FB-1830L-11 MS-2118-11 SO-1930-11
ED12562
Product 1192
Rev 4 – 28 October 2002
Copyright ã2002 Daktronics, Inc.
All rights reserved. While every precaution has been taken
in the preparation of this manual, the publisher assumes no
responsibility for errors or omissions. No part of this book covered
by the copyrights hereon may be reproduced or copied in any form
or by any means – graphic, electronic, or mechanical, including
photocopying, taping, or information storage and retrieval
systems – without written permission of the publisher.
Note: Please fill in the information below for your
display, and use it as a reference when calling
Daktronics for assistance.
Scoreboard Serial No. _________________
Scoreboard Model No. _________________
Date Installed ________________________
PO Box 5128 331 32nd Ave Brookings SD 57006
Tel [phone] or 877-605-1115 Fax [phone]
www.daktronics.com e-mail: [e-mail]

Table of Contents
Section 1: Introduction............................................................................................... 1-1
1.1 How To Use This Manual ..........................................................................................1-1
1.2 Daktronics Nomenclature...........................................................................................1-2
1.3 Manual Overview.......................................................................................................1-3
1.4 Product Overview....................................................................................................... 1-3
1.5 Model Names .............................................................................................................1-4
1.6 Product Safety Approval ............................................................................................1-4
Section 2: Model Identification .................................................................................. 2-1
Section 3: Specifications............................................................................................ 3-1
3.1 Multi-Section Scoreboards.........................................................................................3-2
Section 4: Component Locations .............................................................................. 4-1
Section 5: Schematics................................................................................................ 5-1
Section 6: Mechanical Installation............................................................................. 6-1
6.1 Scoreboard Protective Devices ..................................................................................6-1
6.2 Footings and Beams ...................................................................................................6-1
6.3 Lifting the Scoreboard................................................................................................6-4
6.4 Scoreboard Mounting.................................................................................................6-5
6.5 Ad Panel Mounting ....................................................................................................6-6
6.6 Optional One- or Two-Line Message Center Mounting ............................................ 6-6
Section 7: Electrical Installation ................................................................................ 7-1
7.1 Power Requirements ..................................................................................................7-1
Grounding ............................................................................................................ 7-2
Power Installation ................................................................................................7-2
7.2 Power and Signal Connection ....................................................................................7-3
Connections Between Sections............................................................................ 7-3
Interconnect Panel Connections ..........................................................................7-4
Section 8: Scoreboard Maintenance and Troubleshooting ..................................... 8-1
8.1 Cabinet Specifications................................................................................................ 8-1
8.2 Component Location and Access...............................................................................8-1
Replacing a Digit .................................................................................................8-2
Replacing a Digit Segment ..................................................................................8-2
Replacing a Breakout Board................................................................................ 8-3
Replacing a Driver...............................................................................................8-3
8.3 Schematic ...................................................................................................................8-4
Table of Contents i

8.4 LED Drivers............................................................................................................... 8-4
8.5 Segmentation and Digit Designation ......................................................................... 8-4
8.6 Power-On Self-Test ................................................................................................... 8-5
8.7 Lightning Protection .................................................................................................. 8-5
8.8 Troubleshooting......................................................................................................... 8-5
8.9 Replacement Parts ..................................................................................................... 8-7
8.10 Daktronics Exchange and Repair and Return Programs............................................ 8-7
Section 9: Team Name Message Center Maintenance .............................................9-1
9.1 Team Name Message Center System Overview........................................................ 9-1
9.2 Maintenance and Troubleshooting Overview............................................................ 9-1
9.3 Signal Summary......................................................................................................... 9-2
9.4 Power Summary......................................................................................................... 9-2
9.5 Service and Diagnostics............................................................................................. 9-2
TNMC Current Loop Interface Card................................................................... 9-3
TNMC Controller................................................................................................ 9-4
Modules and Drivers........................................................................................... 9-6
Power Supplies.................................................................................................... 9-7
Weatherstripping................................................................................................. 9-7
9.6 TNMC Display Maintenance..................................................................................... 9-8
9.7 Troubleshooting......................................................................................................... 9-8
9.8 Initialization Information at Startup .......................................................................... 9-9
9.9 Replacement Parts List .............................................................................................. 9-9
9.10 TNMC Exchange and Repair and Return Programs................................................ 9-10
Section 10: Scoreboard Options ................................................................................10-1
10.1 Football Scoreboard Accessories............................................................................. 10-1
10.2 Captions for Other Sports ........................................................................................ 10-1
Installing and Changing Captions ..................................................................... 10-1
10.3 Trumpet Horn .......................................................................................................... 10-2
120 V Trumpet Horn Installation (Internally Mounted) ................................... 10-2
DC Trumpet Horn Installation (Externally Mounted) ...................................... 10-3
10.4 Radio Control........................................................................................................... 10-4
Appendix A: Reference Drawings................................................................................... A-1
Appendix B: Eyebolts..................................................................................................... B-1
ii Table of Contents

Section 1: Introduction
1.1 How To Use This Manual
This manual explains the installation of Daktronics Outdoor LED Timing Displays and provides
details for display maintenance. For other questions regarding the safety, installation, operation, or
service of these systems, contact Daktronics. Customer Service Help Desk telephone numbers are
listed on the cover page of this manual. This manual would be referred to as ED12562.
Important Safeguards:
1. Read and understand these instructions before installing the display.
2. Do not drop the control console or allow it to get wet.
3. Properly ground the timer with a grounding electrode at the display location.
4. Disconnect power when the display is not in use.
5. Disconnect power when servicing the display.
6. Do not modify the structure or attach any panels or coverings to the display without the
express written consent of Daktronics, Inc.
The box at right illustrates the Daktronics drawing numbering system. Daktronics identifies
individual engineering drawings by the
drawing number (7087-P08A-69945 in
the example), which is located in the
lower right corner of the drawing. This
manual refers to drawings by their last set
of digits and the letter preceding them.
The example would be Drawing A-
69945.
Figure 1: Daktronics Drawing Label
Reference drawings are grouped and
inserted in alphanumeric order in the
Appendix.
Listed below are a number of drawing types commonly used by Daktronics, along with the
information that each is likely to provide.
+ System Riser Diagrams: overall system layout from control room to display, power, and phase
requirements.
+ Shop Drawings: fan locations, transformer locations, mounting information, power and signal
entrance points, and access method (front or rear).
+ Schematics: power wiring, signal wiring, panelboard or power termination panel assignments,
signal termination panel assignments, and transformer assignments.
+ Final Assembly: component locations, part numbers, display dimensions, and
assembly/disassembly instructions.
Introduction 1-1

All references to drawing numbers, appendices, figures, or other manuals are presented in bold
typeface, as in this example: “Refer to Drawing A-114667 for the location of the driver
enclosure.” Additionally, any drawings referenced within a particular subsection are listed at the
beginning of that subsection in the following manner:
Reference Drawing:
Shop Drawing; 16 High 2 ½" Small Matrix................................... Drawing A-114667
Daktronics identifies each manual by assigning an engineering document, or ED, number, which is
located on the cover page. This manual, for example, would be referred to as ED13313.
The serial and model numbers of a Daktronics scoreboard can be found on the ID label on the display.
The label will be similar to
the one shown in Figure 2.
When calling Daktronics
Customer Service, please
have this information
available to ensure that
1-2 Introduction
your request is serviced
as quickly as possible. For
future reference, note your scoreboard model number, serial number, and installation date on the front
page of this manual.
Figure 2: Scoreboard Label
Daktronics displays are built for long life and require little maintenance. However, from time to time,
certain display components will have to be replaced. The Replacement Parts List in Section 4
provides names and part numbers of components that may require replacement during the life of this
display.
Following the Replacement Parts List is an explanation of Daktronics exchange and replacement
programs. Refer to these instructions if you must replace or repair any display component.
1.2 Daktronics Nomenclature
To fully understand some Daktronics drawings, such as schematics, it is necessary to know how
various components are labeled in those drawings. You will find this information useful when trying
to communicate maintenance or troubleshooting efforts.
The label "A" on a drawing item typically denotes an assembly. An assembly can be a single circuit
board or a collection of components that function together, usually mounted on a single plate or in a
single enclosure.
In addition, the following labeling formats might be found on various Daktronics drawings:
+ "TB_ _" denotes a termination block for power or signal cable.
+ "F_ _" denotes a fuse.
+ "E_ _" denotes a grounding point.
+ "J_ _" denotes a power or signal jack.
+ "P_ _" denotes a power or signal plug for the opposite jack.

Finally, Daktronics part numbers are commonly listed on drawings. Those part numbers can be used
when requesting replacement parts from Daktronics Customer Service. Take note of the following
part number formats. (Not all possible formats are listed here.)
+ "0P-_ _ _ _-_ _ _ _" denotes an individual circuit board, such as a driver board.
+ "0A-_ _ _ _-_ _ _ _" denotes an assembly, such as a circuit board and the plate or bracket to
which it is mounted. A collection of circuit boards working as a single unit may also carry an
assembly label.
+ "W-_ _ _ _" denotes a wire or cable. Cables may also carry the assembly numbering format in
certain circumstances. This is especially true of ribbon cables.
+ "F-_ _ _ _" denotes a fuse.
+ "T-_ _ _ _" denotes a transformer.
+ "PR-_ _ _ _ _ -_" denotes a specially ordered part.
+ "M-_ _ " denotes a metal part, and "0M_ _ _ _ _ _" typically denotes a fabricated metal
assembly.
1.3 Manual Overview
This manual details outdoor LED timing displays with numeric digits. It is divided into the following
sections:
Section 1: Provides an overview of the product, product safety information, labeling and
numbering descriptions.
Section 2: Contains a list of drawings to be used in model identification.
Section 3: Contains specifications for scoreboard models listed in this manual.
Section 4: Contains a list of drawings listing component locations.
Section 5: Lists specific schematic drawings for each scoreboard model.
Section 6: Contains information regarding mechanical installation.
Section 7: Contains information pertaining to electrical installation.
Section 8: Provides details concerning scoreboard maintenance and troubleshooting.
Section 9: Provides information for team name message center maintenance.
Section 10: Lists optional scoreboard features.
Appendix A: Contains all engineering drawings referenced in the manual.
Appendix B: Contains information about eyebolts and scoreboard lifting.
The various sections in this manual contain model-specific information, including dimensions, digit
configuration, and power requirements. The scoreboard engineering drawings, located in Appendix A,
also list dimensions, weight, and mounting instructions for each display. Additionally, the model
number and electrical requirements can be found on a label on the display entrance panel.
1.4 Product Overview
Daktronics outdoor LED scoreboards are part of a family of scoring and timing displays designed to
offer easy installation, readability and reliability. Microprocessor control assures consistent operation
and accuracy.
Introduction 1-3

Featuring large, highly visible digits 15, 18, 24, and 30" tall, the boards use light-emitting diodes to
power the scoreboard display. (Light-emitting diodes, or LEDs, are tiny, solid-state lighting units.
They are low-energy, high intensity lighting components.) Scoreboards in this series use red-orange
LEDs for maximum outdoor visibility.
Because of their LED technology, the scoreboards consume little power. Power usage in this series
ranges from little more than a household lamp.
The scoreboards in this series are modular in construction, typically with a top and a bottom section,
but some with as many as four different sections. The units are shipped separately and joined at
installation. Unpowered sections, connected to the internal power and signal panels with cabling, are
referred to as slave sections, while those housing the electronic control components are masters.
Cabinets for the displays are of heavy-gauge aluminum construction. Mounting weights and
dimensions for each model are listed in Section 3 of this manual.
KNote: Some drawings and text in this manual refer to team name message centers, or TNMCs.
Team name message centers are scoreboard-mounted matrix LED units which electronically display
home and guest team names. TNMCs are available as a standard new scoreboard option with many of
the models in this series, and the message centers are also available for retrofit on existing
scoreboards. With some TNMC systems still in development, additional models will be added to
subsequent editions of this manual. Section 10 of this manual offers step-by-step information of
TNMC maintenance and troubleshooting.
1.5 Model Names
Daktronics scoreboards are differentiated by their model numbers: FB-1624, for example, designates
a specific football scoreboard. The two-letter prefixes for scoreboards in this manual include the
following: BA- baseball; FB-football; MS-multi-sport, and SO-soccer.
In the outdoor LED scoreboard series, the three or four numbers following the prefix typically
identify a specific model.
Most Daktronics scoreboards also carry a two-number suffix that refers to indoor-outdoor status and
power supply: -9 and -10 are indoor displays, 120 V and 230 V respectively; and -11 and -12 are
outdoor scoreboards, 120 V and 230 V. All of the LED displays in this manual carry the -11 suffix,
signifying that they have been designed and manufactured for outdoor use and have a 120 V AC
power requirement.
1.6 Product Safety Approval
Daktronics outdoor scoreboards and timing displays are ETL listed, tested to CSA standards and CE
labeled for outdoor use. Contact Daktronics with any questions regarding testing procedures
1-4 Introduction

Section 2: Model Identification
Use the following drawings to determine the scoreboard model number. The drawings are listed here
in alphabetical order by scoreboard model line, and they are inserted in the Appendix in
alphanumeric order. Individual scoreboard drawings are also grouped in the Appendix.
Reference Drawing:
Multi-Section Baseball Scoreboards .............................................. Drawing A-126086
Multi-Section Baseball Scoreboards, w/TNMC............................... Drawing A-126362
Multi-Section Football Scoreboards ................................................. Drawing A-42148
Multi-Section Football Scoreboards, w/TNMC ................................. Drawing A-84233
Multi-Section Multi-sport Scoreboards ........................................... Drawing A-128203
Multi-Section Soccer Scoreboards................................................... Drawing A-98161
Multi-Section Soccer Scoreboards w/TNMC .................................. Drawing A-128172
Model Identification 2-1

Section 3: Specifications
The chart on the following pages shows all of the mechanical specifications, circuit specifications and
maximum power requirements for each model in this manual. Models are listed in alphanumeric
order.
Specifications 3-1

3.1 Multi-Section Scoreboards
Note: Signal wires must be a minimum of 22 gauge with shield. Daktronics recommends using W-1234.
(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H8'-0", W16'-0", D6"
(2438 mm, 4877 mm,
152 mm)
Top H3'-0", W16'-0", D6"
(914 mm, 4877 mm,
152 mm)
BA-1518-11
Bottom H5'-0", W16'-0", D6"
(1524 mm, 4877 mm,
152 mm)
400 lb
182 kg
(845 lb)
(383 kg)
¡ Indicators
2" (51 mm)
¡ All Others
18" (457 mm)
250 W 120 V AC 2.1 A A1 63
2 Total H8'-0", W16'-0", D6"
(2438 mm, 4877 mm,
152 mm)
Top H3'-0", W16'-0", D6"
(914 mm, 4877 mm,
152 mm)
BA-1518-11
w/TNMC
Bottom H5'-0", W16'-0", D6"
(1524 mm, 4877 mm,
152 mm)
480 lb
218 kg
(912 lb)
(414 kg)
¡ Indicators
2" (51 mm)
¡ All Others
18" (457 mm)
550 W 120 V AC 4.6 A A1 63
(Continued on the next page)
3-2 Specifications

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H9'-0", W16'-0", D6"
(2743 mm, 4877 mm,
152 mm)
Top H4'-0", W16'-0", D6"
(2743 mm, 4877 mm,
152 mm)
BA-1524-11
Bottom H5'-0", W16'-0", D6"
(1524 mm, 4877 mm,
152 mm)
480 lb
218 kg
(1020 lb)
(463 kg)
¡ Runs, Hits, Errors
18" (457 mm)
¡ Indicators
2" (51 mm)
¡ All Others
24" (610 mm)
340 W 120 V AC 2.8 A A1 63
4 Total H9'-4", W36'-0", D6"
(2845 mm, 10973
mm, 152 mm)
2 Top H4'-0", W18'-0", D6"
(1219 mm, 5486 mm,
152 mm)
BA-2007-11
w/TNMC
2 Bottom H5'-4", W18'-0", D6"
(1626 mm, 5486 mm,
152 mm)
840 lb
381 kg
2 crates
(700 lb)
(318 kg)
(1125 lb)
(510 kg)
¡ Innings, Runs, Hits,
Errors
18" (457 mm)
¡ All Others
24" (610 mm)
1000 W 120 V AC 8.0 A A1 64
A2 65
A3 66
A4 11
4 Total H7'-0", W28'-0", D6"
(2134 mm, 8534 mm,
152 mm)
2 Top H3'-0", W14'-0", D6'
(914 mm, 8534 mm,
152 mm)
BA-3718-11
2 Bottom H4'-0", W14'-0", D6"
(1219 mm, 4267 mm,
152 mm)
640 lb
291 kg
2 crates
(825 lb)
(374 kg)
(525 lb)
(238 kg)
¡ Innings, Runs, Hits,
Errors
15" (381 mm)
¡ All Others
18" (457 mm)
650 W 120 V AC 5.5 A A1 64
A2 65
A3 66
(Continued on the next page)
Specifications 3-3

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
4 Total H7'-0", W28'-0", D6"
(2134 mm, 8534 mm,
152 mm)
2 Top H3'-0", W14'-0", D6"
(914 mm, 8534 mm,
152 mm)
BA-3718-11
w/TNMC
2 Bottom H4'-0", W14'-0", D6"
(1219 mm, 4267 mm,
152 mm)
720 lb
327 kg
2 crates
(746 lb)
(338 kg)
(468 lb)
(212 kg)
¡ Innings, Runs, Hits,
Errors
15" (381 mm)
¡ All Others
18" (457 mm)
950 W 120 V AC 7.8 A A1 64
A2 65
A3 66
4 Total H9'-4", W36'-0", D6"
(2845 mm, 10973
mm, 152 mm)
2 Top H4'-0", W18'-0", D6"
(2845 mm, 5486 mm,
152 mm)
BA-3724-11
2 Bottom H5'-4", W18'-0", D6"
(1626 mm, 5486 mm,
152 mm)
840 lb
381 kg
2 crates
(700 lb)
(318 kg)
(1125 lb)
(510 kg)
¡ Innings, Runs, Hits,
Errors
18" (457 mm)
¡ All Others
24" (610 mm)
695 W 120 V AC
5.8 A A1 64
A2 65
A3 66
BA-3724-11
w/TNMC
4 Total H9'-4", W36'-0", D6"
(2845 mm, 10973
mm, 152 mm)
960 lb
435 kg
2 crates
(856 lb)
(388 kg)
(1112 lb)
(504 kg)
¡ Innings, Runs, Hits,
Errors
18" (456 mm)
¡ All Others
24" (610 mm)
990 W 120 V AC 8.25 A A1 64
A2 65
A3 66
(Continued on the next page)
3-4 Specifications

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H8'-0", W18'-0", D6"
(2438 mm, 5486 mm,
152 mm)
FB-1424-11
Top and
Bottom
H4'-0", W18'-0", D6"
(1219 mm, 5486 mm,
152 mm)
400 lb
182 kg
(805 lb)
(365 kg)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
2 Total H8-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1430-11
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7620 mm,
152 mm)
560 lb
254 kg
(1068 lb)
(484 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
360 W 120 V AC 3 A A1 12
2 Total H8-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1430-11
w/TNMC
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7620 mm,
152 mm)
760 lb
345 kg
(1444 lb)
(655 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
660 W 120 V AC 5.5 A A1 12
2 Total H8'-0", W18'-0", D6"
(2438 mm, 5486 mm,
152 mm)
FB-1524-11
Top and
Bottom
H4'-0", W18'-0", D6"
(1219 mm, 5486 mm,
152 mm)
400 lb
182 kg
(805 lb)
(365 kg)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
360 W 120 V AC 3 A A1 12
2 Total H8'-0", W18'-0", D6"
(2438 mm, 5486 mm,
152 mm)
FB-1524-11
w/TNMC
Top and
Bottom
H4'-0", W18'-0", D6"
(1219 mm, 5486 mm,
152 mm)
520 lb
236 kg
(844 lb)
(383 kg)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
660 W 120 V AC 5.5 A A1 63
(Continued on the next page)
Specifications 3-5

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H8'-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1530-11
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7630 mm,
152 mm)
580 lb
263 kg
(1102 lb)
(499 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
430 W 120 V AC 3.6 A A1 12
2 Total H8'-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1530-11
w/TNMC
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7630 mm,
152 mm)
700 lb
318 kg
(1330 lb)
(603 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
730 W 120 V AC 6.1 A A1 12
2 Total H8'-0", W18'-0", D6"
(2438 mm, 5486 mm,
152 mm)
FB-1624-11
Top and
Bottom
H4'-0", W18'-0", D6"
(1219 mm, 5486 mm,
152 mm)
440 lb
200 kg
(900 lb)
(408 kg)
¡ Indicators
8" (203 mm)
¡ All Others
24" (610 mm)
390 W 120 V AC 3.25 A A1 15
A2 16
2 Total H8'-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1630-11
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7630 mm,
152 mm)
600 lb
272 kg
(1140 lb)
(517 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
395 W 120 V AC 3.3 A A1 15
A2 16
(Continued on the next page)
3-6 Specifications

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H8'-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1630-11
w/TNMC
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7630 mm,
152 mm)
620 lb
281 kg
(1178 lb)
(534 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
695 W 120 V AC 5.8 A A1 15
A2 16
2 Total H8'-0", W32'-0", D6"
(2438 mm, 9754 mm,
152 mm)
FB-1630L-11
Top and
Bottom
H4'-0", W32'-0", D6"
(1219 mm, 9754 mm,
152 mm)
720 lb
327 kg
(1368 lb)
(621 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
395 W 120 V AC 3.3 A A1 15
A2 16
2 Total H8'-0", W32'-0", D6"
(2438 mm, 9754 mm,
152 mm)
FB-1630L-11
w/TNMC
Top and
Bottom
H4'-0", W32'-0", D6"
(1219 mm, 9754 mm,
152 mm)
840 lb
381 kg
(1596 lb)
(724 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
695 W 120 V AC 5.8 A A1 15
A2 16
(Continued on the next page)
Specifications 3-7

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H8'-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1730-11
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7630 mm,
152 mm)
620 lb
281 kg
(1178 lb)
(534 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
400 W 120 V AC 3.3 A A1 15
A2 16
2 Total H8’-0”, W25’-0”, D6”
(2438 mm, 7620 mm,
152 mm)
FB-1730-11
w/TNMC
Top and
Bottom
H4’-0”, W25’-0”, D6”
(1219 mm, 7620 mm,
152 mm)
740 lb
336 kg
(1406 lb)
(638 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
¡ 24" (610 mm)
700 W 120 V AC 5.8 A A1 15
A2 16
2 Total H8'-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
Top and
Bottom
H4'-0", W25'-0", D6"
(1219 mm, 7630 mm,
152 mm)
FB-1830-11 640 lb
291 kg
(1550 lb)
(703 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
430 W 120 V AC 3.6 A A1 15
A2 16
(Continued on the next page)
3-8 Specifications

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H8'-0", W25'-0", D6"
(2438 mm, 7620 mm,
152 mm)
FB-1830-11
w/TNMC
Top and
Bottom
H3'-0", W14'-0", D6'
(914 mm, 8534 mm,
152 mm)
760 lb
345 kg
(1444 lb)
(655 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
730 W 120 V AC 6.1 A A1 15
A2 16
2 Total H8'-0", W32'-0", D6"
(2438 mm, 9754 mm,
152 mm)
FB-1830L-11
Top and
Bottom
H4'-0", W32'-0", D6"
(1219 mm, 9754 mm,
152 mm)
780 lb
354 kg
(1482 lb)
(672 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
450 W 120 V AC 3.8 A A1 15
A2 16
2 Total H8'-0", W32'-0", D6"
(2438 mm, 9754 mm,
152 mm)
FB-1830L-11
w/TNMC
Top and
Bottom
H4'-0", W32'-0", D6"
(1219 mm, 9754 mm,
152 mm)
900 lb
408 kg
(1710 lb)
(776 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
755 W 120 V AC 6.3 A A1 15
A2 16
(Continued on the next page)
Specifications 3-9

(Continued from previous page)
Model Number
of
Sections
Dimensions
(Height, Width,
Depth)
Weight
Uncrated
(Crated)
Digit Size Maximum
Wattage
Power Amps Per
Line
(Single
Phase)
Driver
Number and
Address
2 Total H10'-0", W32'-0", D6"
(3048 mm, 9754 mm,
152 mm)
Top H6'-0", W32'-0", D6"
(1829 mm, 9754 mm,
152 mm)
FB-2001-11
Bottom H4'-0", W32'-0", D6"
(1219 mm, 9754 mm,
152 mm)
940 lb
426 kg
(1786 lb)
(810 kg)
¡ Clock
30" (457 mm)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
455 W 120 V AC 3.8 A A1 15
A2 16
2 Total H8'-0", W20'-0", D6"
(2438 mm, 6096 mm,
152 mm)
Top H6'-0", W20'-0", D6"
(1219 mm, 6096 mm,
152 mm)
FB-2002-11
Bottom H4'-0", W20'-0", D6"
(1219 mm, 6096 mm,
152 mm)
520 lb
236 kg
(988 lb)
(448 kg)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
365 W 120 V AC 3 A A1 15
A2 16
FB-2003-11
w/TNMC
2 Total H8'-0", W20'-0", D6"
(2438 mm, 6096 mm,
152 mm)
660 lb
299 kg
(1254 lb)
(569 kg)
¡ Indicators
8" (203 mm)
¡ TOL
18" (457 mm)
¡ All Others
24" (610 mm)
695 W 120 V AC 5.8 A A1 15
A2 16
(Continued on the next page)
3-10 Specifications