DANA BREVINI D Series Manual

®
Installation and Maintenance Manual
October 2022
IMM-0016EN
Gearmotors D Series

CONTENTS
The official language chosen by the Product manufacturer is English. No liability is assumed as a result of translations in
other languages not in compliance with the original meaning. In case of conflicting language versions of this document, the
English original prevails. Dana shall not be liable for any misinterpretation of the content here into. Photos and illustrations
might not represent the exact product.
© Copyright 2022 Dana Incorporated
All content is subject to copyright by Dana and may not be reproduced in whole or in part by any means, electronic or oth-
erwise, without prior written approval.
THIS INFORMATION IS NOT INTENDED FOR SALE OR RESALE, AND THIS NOTICE MUST REMAIN ON ALL COPIES.
DISCLAIMER

3IMM-0016EN - Installation and Maintenance Manual Dana Incorporated
CONTENTS
1 VERSION TRACKING ....................................................................................................................... 5
1.1 MANUAL APPLICABILITY AND SUPPORTED MODELS ..................................................................... 5
2 HOW TO USE THIS MANUAL ......................................................................................................... 6
3 UNIT DESIGNATION ......................................................................................................................... 7
3.1 DETAILED UNIT DESIGNATION ........................................................................................................... 7
3.2 NAMEPLATE UNIT DESIGNATION ...................................................................................................... 8
4 PART LIST OF STANDARD TYPE GEAR UNITS ............................................................................. 9
4.1 D..00... TYPES FOR 2 AND 3 STAGED GEAR UNITS .......................................................................... 9
4.2 D..01... TYPES FOR 2 AND 3 STAGED GEAR UNITS ........................................................................ 10
4.3 D..02... TYPES FOR 2 AND 3 STAGED GEAR UNITS ........................................................................ 11
4.4 D..03... TYPES FOR 2 AND 3 STAGED GEAR UNITS ........................................................................ 12
4.5 D...0S... TYPES FOR 2 AND 3 STAGED GEAR UNITS ...................................................................... 13
4.6 D...0E... TYPES FOR 3 STAGED GEAR UNITS .................................................................................. 14
4.7 D..4 SERIES ADDITIONAL STAGE FOR 4 STAGE TYPES ................................................................. 15
4.8 D SERIES 5-6 STAGES TYPES .......................................................................................................... 16
4.9 D SERIES MOTOR FLANGE FOR DIRECT COUPLED TYPES .......................................................... 17
4.10 DN..., DV...TYPES B5, B14 MOTOR FLANGE .................................................................................... 17
4.11 DT... TYPES INPUT BEARING HOUSING WITH SOLID INPUT SHAFT ............................................. 17
5 SAFETY ........................................................................................................................................... 18
5.1 INTENDED USE .................................................................................................................................. 18
5.2 IMPROPER USE ................................................................................................................................. 18
5.3 SAFETY INSTRUCTIONS ................................................................................................................... 19
5.3.1 GENERAL SAFETY INSTRUCTIONS................................................................................................... 19
5.4 TIGHTENING TORQUES .................................................................................................................... 21
5.5 CASE OF FIRE .................................................................................................................................... 21
5.5.1 SUITABLE EXTINGUISHING AGENTS, PROTECTIVE EQUIPMENT................................................... 21
5.5.2 UNSUITABLE EXTINGUISHING AGENTS ........................................................................................... 21
6 THINKS TO CHECK BEFORE THE GEAR UNIT OR GEARED MOTOR IS INSTALLED ............. 22
6.1 TRANSPORTATION ............................................................................................................................ 22
6.2 STORAGE ........................................................................................................................................... 23
7 INSTALLING THE GEAR UNIT ....................................................................................................... 24
7.1 BEFORE YOU START ......................................................................................................................... 24
7.2 CHECK THE SHAFT DIMENSIONS TO FIT ........................................................................................ 24
7.3 CHECK THE AMBIENT TEMPERATURE ............................................................................................ 24
7.4 CHECK THE VOLTAGE SUPPLY ....................................................................................................... 25
7.5 CHECK THE MOUNTING POSITION .................................................................................................27
7.6 USE THE BREATHER PLUG .............................................................................................................. 27
7.7 CHECK THE OIL LEVEL ..................................................................................................................... 27
7.8 CHECK SHAFT ENDS AND MOUNTING FACES ............................................................................... 27
7.9 COVER ABRASIVE AMBIENT ............................................................................................................. 27
7.10 CHECK ACCESSIBILITY TO FILLING, BREATHER AND DRAIN PLUGS .......................................... 27

4
CONTENTS
Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
8 MECHANICAL INSTALLATION ...................................................................................................... 28
8.1 INSTALLING CUSTOMER SHAFT WITH SHOULDER ....................................................................... 29
8.2 INSTALLING CUSTOMER SHAFT WITHOUT SHOULDER ................................................................ 30
8.3 DISASSEMBLING CUSTOMER SHAFT WITH SHOULDER ............................................................... 31
8.4 DISASSEMBLING CUSTOMER SHAFT WITHOUT SHOULDER ........................................................ 32
8.5 SHAFT TIGHTENING TORQUES ........................................................................................................ 33
8.6 ADVISED SHAFT DIMENSIONS AND ACCESSIORIES ..................................................................... 34
8.7 D.07.. - D.97.. DIMENSIONS OF SPLINED HOLLOW SHAFT TO DIN 5480 ...................................... 35
8.8 ASSEMBLING CUSTOMER SHAFT WITH SHRINK DISK .................................................................. 37
8.9 DISASSEMBLING CUSTOMER SHAFT WITH SHRINK DISK ............................................................ 39
8.10 ASSEMBLING GEAR UNIT WITH TORQUE ARM .............................................................................. 40
8.11 FITTING OUTPUTSHAFT ELEMENTS ................................................................................................ 43
8.12 CORRECT POSITION OF OUTPUT SHAFT ELEMENTS .................................................................... 43
8.13 FITTING COUPLINGS ........................................................................................................................ 44
9 MAINTENANCE & INSPECTION .................................................................................................... 45
10 LUBRICATION ................................................................................................................................ 46
10.1 OIL TYPES .......................................................................................................................................... 46
10.2 CHANGING THE OIL .......................................................................................................................... 47
10.3 MOUNTING POSITIONS .................................................................................................................... 48
10.4 OIL PLUGS AND OIL QUANTITIES .................................................................................................... 50
10.4.1 D SERIES 2-3 STAGE OIL LEVEL PLUGS: ......................................................................................... 50
10.4.2 D SERIES 4 STAGE OIL LEVEL PLUGS.............................................................................................. 51
10.4.3 D SERIES 5-6 STAGE OIL LEVEL PLUGS: ......................................................................................... 52
11 TROUBLESHOOTING GUIDE ........................................................................................................53
12 DISPOSAL ....................................................................................................................................... 56
12.1 DISPOSAL OF OIL .............................................................................................................................. 56
12.2 DISPOSAL OF SEALING .................................................................................................................... 56
12.3 DISPOSAL OF METAL ........................................................................................................................ 56

5Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
1 VERSION TRACKING
1.1 MANUAL APPLICABILITY AND SUPPORTED MODELS
File name Revision Date Changes description
IMM-0016EN_Rev.00 Gearmotors D
Series 00 17/10/2022 - Changed layout
Models
Gearmotors D Series

6Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
2 HOW TO USE THIS MANUAL
Take attention to the following safety and warning signs for proper understanding and quick reference.
Table 1:
Hazard pictograms
Table 2:
The operating instructions contain important information to ensure;
• Trouble-free operation
• Fulfilment of any rights to claim under guarantee
The operating instruction must be kept close to the gearbox and must be available in case it is needed.
This operating instruction is written for D series gear units and is applicable only for D series. If any different type of gearbox is
used please ask Dana Motion Systems Italia S.r.l. for the operating instructions of that type.
This instruction can be used only for standard type geared units of Dana Motion Systems Italia S.r.l.. For special application
and modified gear units ask Dana Motion Systems Italia S.r.l. for validity.
This manual does not cover 94/9/EC compatible gearboxes. For 94/9/EC contact Dana Motion Systems Italia S.r.l..
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
Indicates an imminently hazardous situation which, if
not avoided, could result in death or serious injury.
Indicates a situation which, if not avoided, may result
in damage to components.
Indicates information which may make product service
easier to perform.
NOTE:
Important Information.
General danger
Electric current
Moving parts
NOTE:
EC Machinery Directive:
Within terms of the EC machinery directive 2006/42/EC, the gearboxes are considered as not autonomous machine, but
as a component to install in machines.
Operation is prohibited within the area of validity of the EC directive, until it has been determined that the machine, in
which this product is installed, corresponds to the regulations within this directive.
DANGER
WARNING
CAUTION
NOTICE

7Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
3 UNIT DESIGNATION
3.1 DETAILED UNIT DESIGNATION
NOTE:
Detailed D series gear units designation for ordering
(This Designation is different from the short nameplate designation)
Gearbox Type
D Serie
Input Type
R :With Motor
N :IEC B5 / B14 Flanged without Motor
V:IEC B5 / B14 Flanged with Motor
Output Shaft
00 :Hollow Shaft output
01 :Solid Shaft Output
02 :Solid shaft output with IEC B5 /14 Flange
03 :Flanged and Hollow Shaft output
0S :Shrink Disk Output
For DN Types
Number of poles
Revision Number
Motor Size
For DR / DV /Types
Pole Number
Frame Lenght
Motor size
Motor type
Motor Efficiency Class
A06 : 63 B5 A09: 90 B5 A13:132 B5 A25: 250 B5
B06 :63 B14 B09: 90 B14 B13:132 B14 A28: 280 B5
A07 : 71 B5 A10:100 B5 A16:160 B5 A31: 315 B5
B07 :71 B14 B10:100 B14 A18:180 B5
A08 : 80 B5 A11:112 B5 A20:200 B5
B08 :80 B14 B11:112 B14 A22:225 B5
Brake
L
P
S-220 V
Z
01-10 Nm
02-25 Nm
04-40 Nm
05-50 Nm
Housing Size
1...9
D R 4 7 4 .02 3 E90S / 4C - L02
10-100 Nm
20-200 Nm
30-300 Nm
40-400 Nm
Stage
2 Stages
3 Stages
4 Stages
5 Stages
6 Stages
E90S / 4

8
UNIT DESIGNATION
Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
3.2 NAMEPLATE UNIT DESIGNATION
A sample name plate for D Series
Abreviations:
Serial N.: Serial Number
M.Pos.: Mounting Position
Type Designation;
A - Type
B - Motor Size
Type:
DR - With motor
DT - With input shaft
DV - With Motor and IEC Flange
DN - IEC Flange without Motor
NOTE:
Nameplate unit designation is a short abbreviation from the detailed designation.
M. Pos.:
:Oil
Ratio:
:Type
rpm.:Speed
Power : kW
MADE IN TURKEY
Serial N.:
Oil Qty : lt.
DR473.03-90L/4
100524545
1.5 121,49
12 M1
ISO VG320
(Mineral Oil) 6.4
DR473 - 3E71M/4C
AB

9Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
4 PART LIST OF STANDARD TYPE GEAR UNITS
4.1 D..00... TYPES FOR 2 AND 3 STAGED GEAR UNITS
A - Only Valid For 3 Stages
NOTE:
Standard D...00... type basic part diagram. Parts may differ for special applications.
30
24
11
3
3
3
1
2
3
5
29
31
32
33
34
35
18 19 20 21
22
23
25
26 2728
6
7
8
9
10
12
13
14
15
16
17
4
A
Standard Part List
1PinScrew
2Housing
3Plug
4 Cover Plate
5 Screw
6OilSeal
7Circlip
8Spacer
9Bearing
10 Hollow Shaft
11 Key
12 Gear
13 Spacer
14 Bearing
15 Spacer
16 Circlip
17 Seal
18 Closing Cap
19 Circlip
20 Spacer
21 Spacer
22 Bearing
23 Shaft Gear
24 Key
Standard Part List
25 Gear
26 Spacer
27 Bearing
28 Spacer
29 Bearing
30 Gear
31 Key
32 Gear
33 Bearing
34 Circlip
35 Closing Cap
Standard Part List

10
PART LIST OF STANDARD TYPE GEAR UNITS
Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
4.2 D..01... TYPES FOR 2 AND 3 STAGED GEAR UNITS
A - Only Valid For 3 Stages
NOTE:
Standard D...01... type basic part diagram. Parts may differ for special applications.
31
25
11
3
3
1
2
3
5
30
32
33
34
35
36
19 20 21 22
23
24
26
27 2829
6
7
8
9
10
13
14
15
16
17
18
4
12
A
Standard Part List
1PinScrew
2Housing
3Plug
4 Cover Plate
5Bolt
6OilSeal
7Circlip
8Bearing
9Bearing
10 Output Shaft
11 Key
12 Key
13 Gear
14 Spacer
15 Bearing
16 Spacer
17 Circlip
18 Oil Seal
19 Closing Cap
20 Circlip
21 Spacer
22 Spacer
23 Bearing
24 Shaft Gear
Standard Part List
25 Key
26 Gear
27 Spacer
28 Bearing
29 Spacer
30 Bearing
31 Gear
32 Key
33 Shaft Gear
34 Bearing
35 Circlip
36 Closing Cap
Standard Part List

PART LIST OF STANDARD TYPE GEAR UNITS
11Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
4.3 D..02... TYPES FOR 2 AND 3 STAGED GEAR UNITS
A - Only Valid For 3 Stages
NOTE:
Standard D...02... type basic part diagram. Parts may differ for special applications.
33
27
11
3
3
3
1
2
3
5
32
34
35
36
37
38
21 22 23 24
25
26
28
29 3031
6
7
8
9
10
13
14
15
16
17
18
4
12
19
20
A
Standard Part List
1PinScrew
2Housing
3Plug
4 Cover Plate
5Bolt
6OilSeal
7Circlip
8Spacer
9Bearing
10 Solid Shaft
11 Key
12 Key
13 Gear
14 Spacer
15 Bearing
16 Spacer
17 Circlip
18 Seal
19 Flange
20 Bolt
21 Closing Cap
22 Circlip
23 Spacer
24 Spacer
25 Bearing
Standard Part List
26 Shaft Gear
27 Key
28 Gear
29 Spacer
30 Bearing
31 Spacer
32 Bearing
33 Gear
34 Key
35 Shaft Gear
36 Bearing
37 Circlips
38 Closing Cap
Standard Part List

12
PART LIST OF STANDARD TYPE GEAR UNITS
Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
4.4 D..03... TYPES FOR 2 AND 3 STAGED GEAR UNITS
A - Only Valid For 3 Stages
NOTE:
Standard D...03... type basic part diagram. Parts may differ for special applications.
32
26
11
3
3
3
1
2
3
5
31
33
34
35
36
37
20 21 22 23
24
25
27
28 2930
6
7
8
9
10
12
13
14
15
16
17
4
18
19
A
Standard Part List
1PinScrew
2Housing
3Plug
4 Cover Plate
5Bolt
6OilSeal
7Circlip
8Spacer
9Bearing
10 Hollow Output Shaft
11 Key
12 Gear
13 Spacer
14 Bearing
15 Spacer
16 Circlip
17 Oil Seal
18 Flange
19 Bolt
20 Closing Cap
21 Circlip
22 Spacer
23 Spacer
24 Bearing
25 Shaft Gear
Standard Part List
26 Key
27 Gear
28 Spacer
29 Bearing
30 Spacer
31 Bearing
32 Gear
33 Key
34 Gear
35 Bearing
36 Circlip
37 Closing Cap
Standard Part List

PART LIST OF STANDARD TYPE GEAR UNITS
13Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
4.5 D...0S... TYPES FOR 2 AND 3 STAGED GEAR UNITS
A - Only Valid For 3 Stages
NOTE:
Standard D...0S... type basic part diagram. Parts may differ for special applications.
31
25
12
4
4
4
1
3
4
6
30
32
33
34
35
36
19 20 21 22
23
24
26
27 2829
7
8
9
10
11
13
14
15
16
17
18
5
2
A
Standard Part List
1PinScrew
2ShrinkDisk
3Housing
4Plug
5 Cover Plate
6Bolt
7OilSeal
8Circlip
9Spacer
10 Bearing
11 Output shaft
12 Key
13 Gear
14 Spacer
15 Bearing
16 Spacer
17 Circlip
18 Oil Seal
19 Closing Cap
20 Circlip
21 Spacer
22 Spacer
23 Bearing
24 Shaft Gear
25 Key
Standard Part List
26 Gear
27 Spacer
28 Bearing
29 Spacer
30 Bearing
31 Gear
32 Key
33 Shaft Gear
34 Bearing
35 Circlip
36 Closing Cap
Standard Part List

14
PART LIST OF STANDARD TYPE GEAR UNITS
Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
4.6 D...0E... TYPES FOR 3 STAGED GEAR UNITS
NOTE:
Standard D...0E... type basic part diagram. Parts may differ for special applications.
1
2
3
4
5
6
7
8
9
9
10
11
12
Standard Part List
1Circlip
2Spacer
3Flange
4Bolt
5 Extruder Neck
6Bolt
7Seal
8Bearing
9Key
10 Hollow Shaft Output
11 Spacer
12 Seal

PART LIST OF STANDARD TYPE GEAR UNITS
15Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
4.7 D..4 SERIES ADDITIONAL STAGE FOR 4 STAGE TYPES
NOTE:
Standard D..4 type additional stage basic part diagram. Parts may differ for special applications.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
4
Parts List
1Circlips
2Bearing
3 Gear
4Oilplug
5Bearing
6Circlips
7Shaft
8Seal
9 Gear
10 Circlips
11 Key
12 Key
13 Bolt
14 Additional Housing
15 Screw Pin
Parts List

16
PART LIST OF STANDARD TYPE GEAR UNITS
Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
4.8 D SERIES 5-6 STAGES TYPES
N Type 2 and 3 stages are additional housing of D series 5 stages and 6 stages of gear units.
A - Only Valid For 6 Stages
NOTE:
Standard N type 3 stages basic part diagram. Parts may differ for special applications.
1
2
3
4
5
6
7
9
11
8
12
16
18
19
20
21
22
23 24
15
17
25
10
26 27
28
30
31 32
29
34 35
36
37
38
33
14
13
A
Parts List
1Housing
2Oilplug
3Circlips
4Bearing
5Spacer
6 Gear
7Bearing
8Key
9 Gear
10 Bearing
11 Circlips
12 Cover
13 Output Flange
14 Bolt
15 Key
16 Output Shaft
17 Key
18 Seal
19 Circlips
20 Bearing
21 Spacer
22 Gear
23 Bearing
24 Circlips
25 Cover
Parts List
26 Circlips
27 Bearing
28 Gear
29 Key
30 Gear
31 Bearing
32 Circlips
33 Oil plug
34 Bolt
35 Eye bolt
36 Oil plug
37 Top side cover
38 Screw Pin
Parts List

PART LIST OF STANDARD TYPE GEAR UNITS
17Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
4.9 D SERIES MOTOR FLANGE FOR DIRECT COUPLED TYPES
4.10 DN..., DV...TYPES B5, B14 MOTOR FLANGE
4.11 DT... TYPES INPUT BEARING HOUSING WITH SOLID INPUT SHAFT
Parts List
1Shaft
2Circlips
3Bearing
4Circlips
5Flange
6Key
7 Gear
8Circlips
9Nut
10 Key
1
2
3
4
5
6
7
8
10
9
Parts List
1Shaft
2Circlips
3Bearing
4Circlips
5B5/B14Flange
6Seal
7 Gear
8Circlips
9Nut
10 Key
1
2
3
4
5
6
7
8
10
9
Parts List
1Seal
2Nut
3Flange
4Shaft
5Bearing
6Bearing
7Circlips
8 Gear
9Circlips
10 Key
11 Key
1
2
3
4
5
6
7
8
9
11
10

18 Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
5 SAFETY
5.1 INTENDED USE
The gear reducer is designed for use in industrial machines. Please refer to our catalogue or our web page for the maximum
permitted torques and speeds. The most important maximum permitted values are indicated on the nameplate of the product.
But the whole data can be found on our product catalogues. Using the product out of the product catalogue / nameplate's per-
mitted ranges will cancel the warranty/manufacturer declaration and Dana Motion Systems Italia S.r.l. will not take any respon-
sibility.
The gear units are intended for industrial machines and may only be used in accordance with the information provided in this
manual the product catalogue and the nameplate of the gearbox. They comply with the applicable standards and regulations
and meet the requirements of the directive 2006/42/EC. The gearbox must be started up, maintained and operated according
this manual. The gearbox most be incorporated with 2006/42/EC confirming parts/machines.
5.2 IMPROPER USE
The operation of the gear reducer is prohibited if:
• It was not mounted/installed according to regulations and this manual
• The gear reducer is very soiled
• It is operated without lubricant
• It is operated out of the permitted values provided on catalogues and/or nameplate.
NOTE:
A motor connected to the gear unit is only allowed to be operated in the frequency entries so that the data provided on
nameplate/catalogue of the gear unit is not exceeded and is accordance with the nameplate/catalogue. The speed
range will be provided on the name plate if Dana Motion Systems Italia S.r.l. is informed that the gear unit will be used
with frequency inverter. If not informed the nameplate will have a single fixed speed and only this speed is allowed.
The electric motor and frequency inverter must be in accordance with 2006/42/EC.
NOTE:
If the gear units input is used with variable speed gear unit, this must be informed to Dana Motion Systems Italia S.r.l.
before ordering and on the nameplate the allowed maximum and minimum speeds (speed range) will be provided. If not
mentioned by ordering the gear units speed will be a fixed single input speed and only this speed is allowed.
NOTE:
If the gear unit will be driven by belt / coupling / chain drive etc. the gear unit is only allowed to be used according the
nameplate/catalogue entries. Different speed, higher motor power, higher radial/axial loads etc. than nameplate/cata-
logue is not allowed.
NOTE:
The ambient temperature must be between +5 - +40 ºC and no abrasive media must attack the paint and seals. If differ-
ent working conditions this must be informed to Dana Motion Systems Italia S.r.l. before ordering.
The gearbox maintenance (oil change / check ) must be done according this manual.
NOTE:
Every usage which exceeds the limits stated above, the nameplate and catalogue of the product (especially higher
torques and speeds) is not compliant with the regulations, and thus prohibited.

SAFETY
19Dana IncorporatedIMM-0016EN - Installation and Maintenance Manual
5.3 SAFETY INSTRUCTIONS
5.3.1 GENERAL SAFETY INSTRUCTIONS
5.3.1.1 Working on the gear reducer
5.3.1.2 Operation
5.3.1.3 Maintenance
WARNING
Inappropriately executed work can lead to injury or damage.
Make sure that the gear reducer is only installed, maintained and dismantled by trained technicians.
WARNING
Foreign bodies spinning through the air can cause grave injury.
Before putting the gear reducer into operation, check that there are no foreign bodies or tools near the gear reducer
WARNING
Touching hot surfaces can lead to burns.
Do not touch the gear reducer if their operation temperatures are too high, or use suitable safety equipment like gloves.
WARNING
Rotating machinery can lead to injuries. There is danger of being trapped or pulled in!
Keep a sufficient distance and make safeguarding to rotating machinery. See relevant norms EN349+A1, EN13857.
WARNING
An unintentional start of the machine during maintenance work can lead to serious accidents.
Make sure no one can start the machine while you are working on it.
WARNING
Even a brief running of the machine during maintenance work can lead to accidents if the safety devices are not operating.
Make sure that all safety devices are mounted and active.

20
SAFETY
Dana Incorporated IMM-0016EN - Installation and Maintenance Manual
5.3.1.4 Lubricant
5.3.1.5 Ambient Conditions
WARNING
Extended, intensive contact with oils can lead to skin irritations.
Avoid extended contact with oil, and clean oil off skin thoroughly.
WARNING
Hot oil can cause scalding.
When changing oil, protect yourself against contacting hot oil.
DANGER
If the gear unit will be used in outdoor applications the gear unit must be prevented from rain snow and dust. Entering sub-
stances inside the gear unit from seals can damage the gear unit. Observe the safety instructions for outdoor use
EN12100:2010.
WARNING
Standard gearboxes are allowed to work in ambient temperatures between +5 to +40ºC unless differently specified on the
nameplate. Using the gear unit out of this range can cause damage to the gear unit or environment. Over +40 ºC ambient
conditions the gear unit surface temp could be so high causing burns when touched.