Danby DAC12344DE User manual

ENGLISH
Window-type Room Air Conditioner (Cool)
Acondicionador de aire doméstico sistema de tipo ventana (Refrigeración)
Climatiseur de type Fenêtre (Refroidissement)
E S F
DB98-16358A(2)
ESPAÑOL
FRANÇAIS
ITALIANO
OWNER’S INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’UTILISATION
DAC6304DE
Model:
DAC8404DE
DAC12344DE
DAC14004D
DAC18030

E-2
The following safety precautions must be taken when installing
and using your air conditioner.
Safety Precautions
1The air conditioner must be plugged into its own specific power source, which must be
installed in compliance with national wiring, earthing and safety regulations.
Depending on national regulations and your specific installation, you may need to install:
◆ A circuit breaker
For further information on electrical requirements, contact a professional electrician.
This device must be installed according to the national electrical rules.
2Make sure that the unit is correctly ventilated at all times;
do NOT place clothing or other materials over it.
4Do NOT insert anything between the air outlet blades, as it may damage the inner fan
and you may be hurt. Keep children away from the unit.
5If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
6Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact:
◆ An authorized service center
◆ The dealer from whom you purchased the air conditioner.
7Do NOT place any blocking objects in front of the unit.
3NEVER spill liquids of any kind into the unit.
Should this happen, unplug the unit and contact your installation specialist.
8If the remote control will not be used for a long time, remove the batteries.
9Before throwing out the device, it is necessary to pull back the battery cells
and get rid of them safely.
10 The appliance is not intended for use by young children or infirm person without supervision;
young children should be supervised to ensure that they do not play with the appliance.
11 Do NOT use an extension cord with this product.
The manufacturer does not assume responsibility for accidents or injury
caused by an incorrectly installed air conditioner. If you are unsure about
installation, contact an installation specialist.
CC
CA AU UT TI IO ON N

E-3
Contents
◆PREPARING YOUR AIR CONDITIONER
■Safety Precautions ......................................................................................... 2
■Description of Each Component .................................................................... 4
■Remote Control - Buttons .............................................................................. 5
■Getting Started ............................................................................................... 6
■Inserting the Remote Control Batteries .......................................................... 7
◆OPERATING YOUR AIR CONDITIONER
■Cooling Your Room ........................................................................................ 8
■Airing Your Room ........................................................................................... 9
■Removing Excess Humidity ............................................................................ 10
■Adjusting the Air Flow Direction Horizontally .................................................. 11
■Adjusting the Air Flow Direction Vertically ...................................................... 11
◆PROGRAMMING YOUR AIR CONDITIONER
■Setting the On Timer ...................................................................................... 12
■Setting the Off Timer ...................................................................................... 13
■Setting the Sleep Timer .................................................................................. 14
■Selecting Energy Saving mode ...................................................................... 15
◆RECOMMENDATIONS FOR USE
■Temperature and Humidity Ranges ................................................................ 16
■Cleaning Your Air Conditioner ........................................................................ 17
■Solving Common Problems ............................................................................ 18
■Technical Specifications ................................................................................. 19
ENGLISH

E- 4
Description of Each Component
The design and shape are subject to
change.
Temperature/Timer
settings
Temperature adjustment
buttons
On/Off button
Mode selection button
(Cool,Fan, Dry)
Sleep timer setting button
Timer setting button
Fan speed adjustment button Remote control
Energy Saver button
Fan!Speed
Mode
Cool/Dry/Fan
E.Saver
Sleep
Timer
Temp.
Power
Outer air flow blades
(up/down orientation)
Ventilation lever
Air outlet
Air inlet (Outside)
Air filter (Inside)
Air outlet
Inner air flow
blades (right/left
orientation)
Air inlet (Inside)
Power plug
(The type of power plug
may differ, depending on
the local power supply.)

E-5
Remote Control - Buttons
Timer setting button Temperature
adjustment buttons
Fan speed
adjustment buttons
On/Off button
Sleep timer setting
button
Mode selection
buttons
Energy Saver button
ENGLISH

E-6
Getting Started
IMPORTANT NOTE
Your Owner’s Instructions contain much valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s features.
The booklet is organized as follows.
◆The following figures are shown on pages 4 and 5:
-Description of Each Component
-Remote control (buttons)
They will help you find the buttons and understand the symbols displayed.
◆In the manual, you will find a series of step-by-step procedures for each function avai-
lable.
The illustrations in the step-by-step procedures use four different symbols:
☛
➢
PRESS PUSH

E-7
Inserting the Remote Control Batteries
Push the battery cover on the rear of the remote control with your thumb
in the direction of the arrow and remove it.
Insert the two batteries, taking care to respect the polarities :
◆+ on the battery with + on the remote control.
◆- on the battery with - on the remote control.
1
2
Close the cover by sliding it back until it clicks into place.
3
◆Use two AAA, LR03 1.5V batteries.
◆Do not use old batteries or different kinds of batteries together.
◆Batteries may be completely discharged after 12 months, even
if they have not actually been used.
You must insert or replace the remote control batteries when :
◆You purchase the air conditioner
◆The remote control does not work correctly
➢
ENGLISH

E- 8
Cooling Your Room
To adjust the temperature, press the or buttons on the remote
control or unit one or more times until the desired temperature is displayed.
The temperature can be set between 18 C and 30 C.
Result: Each time you press the or buttons:
- The temperature is adjusted by 1 C and displayed on
the control panel
- The unit beeps
The air conditioner starts cooling, if the room temperature is
higher than the selected temperature.
If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan is still operating.
3
Press the (On/Off) button.
Result: The air conditioner starts up in the Cool mode.
The unit beeps twice.
The air conditioner is fitted with a protection mechanism to prevent
the unit from being damaged when it is started immediately after
being:
Plugged in
Stopped
It will start up normally after three minutes.
If the temperature is not displayed on the control panel:
 Press the button on the remote control
or
 Press the button on the unit one or more times until the
temperature is displayed.
Result: The unit beeps each time you press the / button.
The air conditioner starts up in the Cool mode.
You can change modes at any time.
You must select the Cool mode if you wish to lower the temperature
in your room. You can also set the Fan speed.
1
2
To set the fan speed:
Press the , or button on the remote control as desired.
or
Press the button on the unit one or more times until the
desired Fan speed(F1, F2 or F3) is displayed.
4
To control the direction of the air flow, refer to page 11.
5
Fan!Speed
Remote Control Control Panel

E- 9
Airing Your Room
If you want to provide air circulation without cooling, you can use
the Fan mode.
If necessary, press the (On/Off) button.
Result: The air conditioner starts up in the Cool mode .
The unit beeps twice.
1
To set the fan speed:
Press the , or button on the remote control as desired.
or
Press the button on the unit one or more times until the
desired fan speed(F1, F2 or F3) is displayed.
3
To control the direction of the air flow, refer to page 11.
4
If the fan speed(F1, F2 or F3) is not displayed on the control panel:
Press the button on the remote control
or
Press the button on the unit one or more times until the fan speed
(F1, F2 or F3) is displayed.
Result: The unit beeps each time you press the / button.
The air conditioner starts up in Fan mode.
You can change modes at any time.
When the air conditioner is in the Fan mode, the temperature
cannot be set or displayed.
2
Mode
Cool/Dry/Fan
Fan!Speed
Mode
Cool/Dry/Fan
Remote Control Control Panel
ENGLISH

E- 10
Removing Excess Humidity
If the atmosphere in your room is very humid or damp, you can remove
excess humidity without lowering the room temperature too much.
1If necessary, press the (On/Off) button.
Result: The air conditioner starts up in the Cool mode.
The unit beeps.
The air conditioner is fitted with a protection mechanism to pre-
vent the unit from being damaged when it is started immediately
after being:
Plugged in
Stopped
It will start up normally after three minutes.
2If the
temperature is not displayed at the top of the control panel, press
the button on the control panel one or more times until it
appears.
Result: The unit beeps each time you press the button.
The air conditioner runs in Dry mode.
You can change modes at any time.
3To adjust the temperature, press the or buttons one or
more times until the required temperature is displayed.
Possible temperatures are between
18 C and 30 C inclusive.
Result: Each time you press the or buttons:
- The temperature is adjusted by 1 C
- The unit beeps
The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
4To control the direction of the air flow, refer to page 11.
Mode
Cool/Dry/Fan
Mode
Cool/Dry/Fan
Remote Control Control Panel

E-11
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust
the orientation of the inner air flow blades on the unit.
Adjust the air flow blades to the desired position by pushing them side to side.
Adjusting the Air Flow Direction Vertically
The outer air flow blades can be adjusted to control the vertical air
flow direction.
RECOMMENDATION When...
Cooling
Adjust the blades to face...
Upwards.
Adjust the air flow blades to the desired position, by pushing them
upwards or downwards.
If you orient the air flow blades downwards and the unit operates
in Cool mode for long periods of time, dew may:
- Form on the surface of the blades
- Drip from the blades
➢
ENGLISH

E- 12
Setting the On Timer
The On Timer enables you to switch on the air conditioner automatically after a
given time. You can select the On timer only when the air conditioner is off. Y ou
can select the On timer when the air conditioner operates in the Cool or Dry mode.
1 Check that the air conditioner has been switched off; if necessary,
press the (On/Off) button.
2 Set the operating time by pressing the button on the remote control
or button on the unit one or more times until the desired time is dis-
played. The operating time can be set between 1 and 24 hours.
Result:Each time you press the button:
- The time is adjusted by 1 hour and displayed on the control
panel
- The unit beeps
The operating time is displayed and decreases automatically to
indicate the remaining time.
The air conditioner starts up in the Cool or Dry mode automati-
cally when the operating time reaches zero.

You can select the fan speed, temperature and Energy saving mode
after setting the On timer and Off timer mode. However, when you
change the mode, the On timer and Off timer mode is canceled.
To cancel the timer, press:
Timer on the remote control or unit one or more times until "--" is displayed.
or
The (On/Off) button on the remote control or unit (The air conditioner
operates in the mode selected when the unit was last used.)
To Cancel the On Timer
Timer
Timer
Remote Control Control Panel

E- 13
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner automatically after a
given time. You can select the Off timer only when the air conditioner is on. You
can select the Off timer when the air conditioner operates in the Cool or Dry mode.
1 Check that the air conditioner has been switched on; if necessary,
press the (On/Off) button.
2 Set the operating time by pressing the button on the remote control
or button on the unit one or more times until the desired time is dis-
played. The operating time can be set between 1 and 24 hours.
Result:Each time you press the button:
- The time is adjusted by 1 hour and displayed on the control
panel
- The unit beeps
The operating time is displayed and decreases automatically to
indicate the remaining time.
The air conditioner switches off automatically when the
operating time reaches zero.

You can select the fan speed, temperature and Energy saving mode
after setting the On timer and Off timer mode. However, when you
change the mode, the On timer and Off timer mode is canceled.
To Cancel the Off Timer
To cancel the timer, press:
Timer on the remote control or unit one or more times until "--" is displayed.
or
The (On/Off) button on the remote control or unit.
Timer
Timer
Remote Control Control Panel
ENGLISH

E- 14
Setting the Sleep Timer
The Sleep Timer can be used when you are cooling your room to switch
the air conditioner off automatically after 8 hours.
If you wish to switch the unit off at a specific time, refer to page 13.
1Make sure that you have selected the Cool mode.
2 Press the button on the remote control
or
Press the button on the unit.
Result: Each time you press a button, the unit beeps.
The " " will be displayed.
The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
The air conditioner will be controlled as illustration below.
To cancel the timer, press:
Sleep on the remote control.
or
Sleep on the unit.
Result:The unit beeps.
The SLEEP indicator is no longer displayed.
The air conditioner operates in the mode selected last.
If you select the Energy Saving mode in the Sleep Timer mode,
the Sleep Timer will be cancelled and the air conditioner will start up
in the Energy Saving mode.
To Cancel the Sleep Timer
Cooling When the temperature has
been increased by 1 C
(after 1 hour), it is maintained
for 7 hours.
Sleep
Remote Control Control Panel

E- 15
Selecting Energy Saving Mode
To select the energy saving mode, press the button on the remote
control or button on the unit one or more times until the Energy
Saver indicator lights up.
Result: The fan and compressor cycle on and off together.
The fan will continue to run for a short time after the
compressor cycles off.
If you would like the air conditioner to run in Dry mode, do not press
the button. You cannot use the Dry mode in the energy saving
mode.
To stop the energy saving mode, press the button on the remote
control or button on the unit again.
Result: The fan runs at all times, while the compressor cycles on and off.
If you select the Sleep Timer in the Energy Saving mode, the Energy
Saving will be cancelled and the air conditioner will start up in the
Sleep Timer mode.
If you wish to save energy when using your air conditioner,
select the energy saving mode.
1
2
E.Saver
E.Saver
E.Saver
E.Saver
E.Saver
Remote Control Control Panel
ENGLISH

E-16
Temperature and Humidity Ranges
If the air conditioner is used at... Then...
Higher temperature The automatic protection feature may be triggered and the air
conditioner stopped.
Lower temperature A water leakage or some other malfunction may happen if the
heat exchanger freezes.
Higher humidity levels Water may condense on and drip from the surface of the unit
if it is used for long periods.
The following table indicates the temperature and humidity ranges
within which the air conditioner can be used.
Mode Indoor Temperature Outdoor Temperature Indoor Humidity
Cooling 21°Cto 32°Capprox. 21°Cto 43°Capprox. 80% or less

E-17
Cleaning Your Air Conditioner
Open the front grille by pulling the tabs on both sides of the grille.
Then lift it up slightly to open the front grille completely.
1
Remove all dust on the air filter with a vacuum cleaner or brush. 3
Grab the tabs on the filter and pull it up and out. 2
When you have finished, insert the air filter back into its original position. 4
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth. (Be sure not to use benzene, solvent or other chemical
products.)
5
Be sure to clean the air filter periodically to maintain the air conditioner
in the best condition for a long period of time.
When cleaning the air conditioner, turn it off and pull out the
power plug.
Set the fan going for a few hours to dry
the inside of the air conditioner tho-
roughly.
If you... Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan going for a few
hours to dry the inside of the air
conditioner thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
➢
☛
ENGLISH

E-18
Solving Common Problems
Explanation / Solution
◆Check that the circuit breaker used for the air conditioner has not been
triggered.
◆ Check that the power cable is plugged into a wall socket and the socket is
switched on, if necessary.
◆ Check that the temperature indicator on the unit is lit; if necessary,
press the (On/Off) button on the remote control or unit.
◆Check that there are no obstacles between you and the unit.
◆ Replace the remote control batteries if necessary.
◆ Check that you are close enough to the unit (seven metres/yards or less).
◆
Ventilate the room.
Problem
The air conditioner does
not
operate at all
The air conditioner does not
operate with the remote
control
Odors are permeating the
room during air conditioning
◆Check that you are pointing the remote control at the remote control sensor
on the unit.
◆ Replace the remote control batteries if necessary.
No beep is heard when you
press the (On/Off) button
on the remote control
◆Check that the correct operating mode has been selected(Cool).
◆ The room temperature may be too low.
◆Dust may be blocking the air filter; refer to page 17 for cleaning instructions.
◆Check that there is no obstacle blocking the air flow into or out of the unit.
The air conditioner does not
cool
◆Check that the timer has been programmed correctly; refer to page 12~14.
The timer is not correctly trig-
gered
Before contacting an authorized service center, perform the following simple checks.
They may save you the time and expense of an unnecessary call.

E- 19
Technical Specifications
ENGLISH
Model Power Supply
DAC6304DE
DAC8404DE
DAC12344DE
DAC14004D
Design and specifications are subject to change without notice.
115V~, 60Hz
DAC18030
208/230V~, 60Hz

S-2
A la hora de instalar y utilizar el acondicionador de aire, se deben tomar las siguientes
precauciones de seguridad.
Instrucciones de seguridad
1El acondicionador de aire debe estar conectado a su toma de alimentación específica,
la cual debe estar instalada de acuerdo con las normas nacionales de cableado, tomas de
tierra y seguridad.
Dependiendo de las normas nacionales y su instalación específica, puede que necesite instalar:
◆ Un disyuntor
Para obtener más información sobre los requisitos eléctricos, póngase en contacto con un
electricista profesional.
Este aparato se debe instalar segun las reglas eléctricas del país.
2Asegúrese de que la unidad se encuentra siempre correctamente ventilada;
NO coloque ropa ni ningún otro material sobre la misma.
4NO introduzca nada entre las guías de salida del aire, ya que se puede dañar el
ventilador interior y el usuario puede resultar lastimado. Sobre todo, mantenga a
los niños alejados de la unidad.
5Si se daña el cable de corriente, debe ser reemplazado por un cable especial o con un
repuesto que el fabricador o el agente de servicio le pueda proveer.
6NO intente reparar la unidad. Si ésta resulta dañada, póngase en contacto con:
◆ Un centro de servicio autorizado
◆ De traficante donde compro su aire acondicionador.
7NO coloque obstáculos de ninguna clase delante de la unidad.
3No derrame NUNCA líquidos de ninguna clase en la unidad. En caso de que esto
ocurra, apague el interruptor del acondicionador de aire y póngase en contacto con
el técnico especialista.
8Si no se va a utilizar el mando a distancia durante un largo período de tiempo, extraiga
las pilas.
9Antes de tirar el aparato, es necesario sacar todas las células de la bateria y librarlo
totalmente y dejar en un lugar seguro.
10 Las aplicaciones no deben ser utilizadas por niños ni por personas deficientes sin
supervisión; se debe vigilar que los niños no jueguen con las aplicaciones.
11 NO use cordón de extensión con este producto.
El manufactor no tomara la responsabilidad de los accidentes causados si el aire
acondicionador no esta instalado firmemente o seguro, durante la instalación o
en el uso del producto. Si no esta seguro sobre la instalación, contacte con su
especialistas en instalación.
CC
CA AU UT TE EL LA A