Danby Pro User manual

DANDY Pro
Paint Brush & Roller Cleaner
The Dandy Pro Can be used with Corded Drills. Cordless Drills and Impact Drivers
4 Solvents should be used in accordance with manufacturers instructions.
1 Recommended drill speed: 1800 - 2500 rpm.
General Recommendations
2 Wipe any solvent spillage off Dandy attachments immediately.
3 Cleaning Brushes - Lower the brush and attachment into a bucket deep enough to contain all spray during
spinning. The top of the brush attachment should be at least 8cm below the rim of the bucket during
spinning.
Cleaning Rollers - Lower the roller sleeve and attachment into a bucket deep enough to contain all spray
during spinning. The top of the roller sleeve should be at least 10cm below the rim of the bucket during
spinning.
5 If the brush handle shape is such that there is no definite point of grip or the brush handle does not appear
to be held tightly it will be helpful to wrap some masking tape around the handle where the jaws locate to
assist grip.
2 To avoid electric shocks ensure hands and drill are dry. Switch off electrical supply immediately if the drill
becomes wet.
4 If using solvents or paints which irritate the skin or eyes or which may cause other damage, use appropriate
protective equipment.
5 A cardboard box can also be used to spin the paint brush or roller sleeve in Place a plastic bin liner around
the outside of the box - do not use it inside the box as it will wrap around the tool when spinning. Spin as
above.
3 If equipment vibrates in use switch off the electrical supply immediately and ensure that the brush or roller
sleeve is located correctly in attachment.
1 Usual precautions should be taken when using electrical tools in the vicinity of liquids.
Important Safety Notes
WARRANTY
Dandy Decorating products carry a TWO YEAR WARRANTY against defective
workmanship and materials. Should your Dandy product fail please contact us at the
address below.
Dandy Tools Ltd 7 Islay Gardens Hampshire PO6 3UF England, Portsmouth,
Tel [phone] email [email protected]
Please note the products are guaranteed for normal use but NOT against misuse.
www.dandytools.com
This guarantee is offered in addition to and does not diminish your statutory rights
All Dandy Products are protected by International Patents.
DANDY
The Dandy Pro Can be used with both Corded Drills, Cordless Drills and Impact Drivers with
3/8" or 10mm Drill Chucks or standard 1/4" or 6mm Impact Driver Chucks.

DANDY Pro Paint Brush & Roller Cleaner
1 Slide the attachment fully into the drill chuck and tighten securely.
Do not connect the drill to the electrical supply at this stage.
This tool can be used with most 10 - 100mm (½" to 4") wide Paint
Brushes in drills with a 10mm chuck capacity.
4 Remove the brush from the attachment by reversing step 2 above
and rinse in an appropriate solvent. Spin as in step 2.
3 Hold the drill with the attachment fixed centrally and vertically in an
empty bucket or other container and spin for 7 seconds.
5 Repeat 3 if necessary.
Paint Brush Cleaning
2 Insert brush into the attachment ensuring that the brush handle
passes between the two Gripper Ends as shown. Ensure that the
tail of the brush handle enters into the Tail Retainer as indicated.
Tighten the gripper end by holding the chuck still while rotating the
brush head clockwise. This will cause the screw mechanism to
draw the Gripper End Piece into the tube which will compress the
Gripper Ends against the brush handle. Do not over tighten but
ensure that the brush handle is gripped tightly enough to hold the
brush whilst spinning. Ensure that the brush is located centrally
across the Gripper Ends. Connect the drill to the electrical supply.
4 Remove the roller sleeve from the attachment and rinse in an
appropriate solvent. Spin as in step 2.
5 Repeat 3 if necessary.
2 Remove the roller sleeve from the frame. Push the sleeve over the
Gripper Ends and on to the attachment. Push the roller sleeve over
the appropriate shoulder until it is gripped securely . Connect the
drill to the electrical supply.
Paint Roller Sleeve Cleaning
3 Hold the drill with the attachment fixed centrally and vertically in an
empty bucket or other container and spin for 7 seconds.
This tool can be used with most 38 and 45mm (1½" and 1¾") Paint
Roller Sleeves from 50 to 450mm (2" to 18") long, in drills with a 10mm
chuck capacity. Remove any burrs which may be on the inside the
ends of the plastic roller sleeve tube to ensure that the roller sleeve will
slide over the shoulders of the cleaner
1 Slide the attachment fully into the drill chuck and tighten securely.
Unscrew the Gripper Ends to maximum width.
It is recommended that you do a dry run of the cleaning processes to ensure that you fully understand the instructions.
The Dandy Pro allows you to clean both paint brushes and rollers with a single tool. The range of brushes is from 10mm(½”) to 100mm(4”) and most shapes of handles. The range of roller sleeves is
around 50mm( 2”) to 450mm(18”) long both 38mm(1½”) to 45mm(1¾”) diameter. On some of the longer roller sleeves the “Roller Gripper Piece” may be used as shown below.heavier or
Rinse
Spin
Dandy
Rinse
Spin
The different colours used in the illustrations are simply to help identify the parts that are referred to in these instructions. To get the most from your Dandy tools see the videos at www.dandytools.com/Videos
Gripper Ends
Tail Retainer
Drill Chuck
Impact Driver Chuck
Drill Chuck
Roller Sleeve
Gripper Ends
Shoulders
Impact Driver Chuck
Drill/Impact Driver Speed
1250-1500rpm
1501-3250rpm
1st Spin
2nd Spin
3rd Spin
4thSpin
5th Spin
Heavy Rollers or rollers longer6 than
225mm (9”) may need to use the Roller
Gripper Piece as shown . Th gripper
helps to steady a long roller
sleeve if it is necessary..
e
or heavy Roller
Gripper
Piece 38 (1½"mm ) 45mm )(1¾"
The Dandy Pro Can be used with both Corded Drills, Cordless Drills and Impact Drivers with
3/8" or 10mm Drill Chucks or standard 1/4" or 6mm Impact Driver Chucks.
Cleaning speeds for both brushes and roller sleeves
Roller
Gripper
Piece
The Dandy Pro Can be used with both Corded Drills, Cordless Drills and Impact Drivers with 3/8" or 10mm Drill Chucks or standard 1/4" or 6mm Impact Driver