Dancing Wings DW PTERODACTYL User manual

DW PTERODACTYL INSTRUCTION MANUAL
Accessories include
A Main Wing
B Tail Wing
C1-5 Parts of Head
D1 Wood parts of Fuselage
D2-3 EPP parts of Fuselage
E Rubber band
F Servo horn
G push-pull rod
H Carbon tape
I Cockpit
J EZ connectors
K1 Servo (with extension line)
K2 Servo (with standard length)
M Prop saver
N Propeller
O ESC
P Foamy glue
Wood parts of Tail Wing
Lead
Q
R
STANDARD SETUP
Preparation Tool
Speci�ication
Wingspan: 1600mm
Length: 860mm
Flying Weight≈720g
Suggested Equipment
Battery: 3s 2200mAh
Motor: 1908 2050kv*2
Propeller: 7035+7035R
ESC: 20A*2
Servos: 9g*4
Radio≥4CH
A
BC1
E
C2 C3
C4
C5
D1
D2
D3
D3
FI
H
G
J
K1 K2 L
O
MNP
Q R
biomimetic aircrafts
EPP
DW PTERODACTYL

DW PTERODACTYL INSTRUCTION MANUAL
How to Assemble
0.01Assemble and glue together the wood parts
marked in number shown.(Pic. 1-3)wing.
0.02 Paste the epp board on both sides of the
fuselage with foamy glue.(Pic. 4-5)
0.03 Assemble and paste the V-shape tail wing with
foamy glue.(Pic. 6-7)
0.04 Glue the small wood parts at the aileron of the
tail wing.(Pic. 8)Assemble the other by same way.
1
2
3
4
5
6
6
Motor mount
Pic.1
Pic.2
Pic.3
Pic.4
1 2
3
45
6
6
D2
Pic.5
Pic.6
Pic.7
Pic.8
D3
D3

DW PTERODACTYL INSTRUCTION MANUAL
0.05 Assemble and glue together the head part,
which should glue onto the fuselage (Pic. 9-10)
0.06 Assemble the two servos with standard length
inside the fuselage and secured by a screw.
0.07 Slide the hinge onto the push-pull rod, lock the
hinges on the aileron wood parts of the tail wing,
put the push-pull rod through the rear tail unit, set
the servo in neutral, and connect the push-pull rod
to servo arm by using EZ connectors.
0.08 Glue together the three pieces of main wings,
cut slots on the back, and insert the carbon tapes by
glue.
Pic.9
Pic.10
C3
Pic.12
Pic.13
Pic.14
Pic.15
Pic.16
Pic.17
C1
C2 C4 C5
Pic.11
490mm
480mm
Carbon tapes
Carbon tapes
Pic.18

DW PTERODACTYL INSTRUCTION MANUAL
0.09 Install the servo (with extension line) at
reserved position; insert the servo wires into slot
and through to the middle position of main wing,
and secured by glue.(Pic. 19)
0.13 Glue the motors into the slots on the leading
edge and connect with ESC.(Pic. 24)
0.14 Insert the ESC wires into slot and secured by
glue.
0.15 Secured the wing and fuselage by rubber band.
0.12 Assemble the motor onto the motor mount and
secured by screws.(Pic.23),and assemble the prop
and prop saver.
0.10 Slide the hinge onto the push-pull rod, set the
servo in neutral, and install the servo horn, the
correct arrangement of aileron servo connection.
(Pic. 21)
0.11 Glue the ESC onto the wood plate at the middle
position of the main wing.
0.16 Install the battery and receiver, put the lead
into the head of the airplane, and adjust the C.G.
Pic.19
Pic.20
Pic.21
Pic.22
Pic.23
Pic.24
Pic.25
Pic.26
45mm
CG
Lead