Dancing Wings SCG42 User manual


Balsawood Scale Airplane
SCG42

ARF
● 这个产品不是玩具，而是一个复杂的具有难度的飞行器。您和您身边人的安全取决于您如何操作它，您需要了解相关知识，并谨慎操作。禁止
没有成人陪伴的儿童独自操作该设备。不适合14岁以下人群使用。再次强调，这不是一个玩具。
● This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends
on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be
accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A
TOY.
● 不要在机场，军事基地，居民区或其他任何受限制的地方飞行。
● Do not fly around some restricted location like airports, military bases, residential areas, etc.
● 您需要对发射机进行距离检查，以确保没有收到任何干扰。
● You will need to range check the transmitter to be sure you are not experiencing any interference.
● 始终保持先打开发射机后打开接收机，先关闭接收机后关闭发射机的步骤。
● Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.
● 如果您是初学者，建议您在有经验玩家的协助下调试和飞行。
● If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from
advanced expert fliers.
● 请将相关物品放置在孩子们够不到的地方
● Keep relevant items out of reach of children.
● 这个设备的设计已经超过我们正常使用所需要刚性要求，但若您需要以超出我们推荐的动力飞行时，请合理控制动作幅度并适当增加机体强度。
● This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform
any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body
strength.
● 您的设备中可能包括一些玻纤和碳纤雕刻的部件，这些纤维部件所带的粉尘可能会引起眼睛，皮肤的不适，请您在需要的时候带上护目镜或者防尘服。
● This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the
goggles or dust-proof clothes when needed.
● 因航空运输安全管制，您收到的产品可能没有清单中出现过的胶水，请您理解无法发送胶水给您的原因。您可以在当地文具店很方便的购买到您所需要
的胶水。
● Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the
glue you need at your local stationery store.
注意事项
SAFETY PRECAUTIONS
● 安装舵机前，请先将舵机通电让舵机中心点回中，以便能更好的调试舵面。
● Check/adjust servo centering, in order to adjust the control surface better.
● 初次启动电机，您需要确认电机旋转的方向以适配您的机型。
● Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.
● 请将重心（CG）调整至说明书所述位置并尽量靠近。如果有需要，您可以增加机头或者机尾的重量，以确保机体有更好的飞行姿态。
● Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to the nose or tail
to ensure the best flight performance.
● 检查机身内部，确保所有设备正常连接；检查机身表面，包括但是不限于蒙皮，固定螺丝，舱盖，座舱罩等位置。
● Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the heat-shrink
covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.
● 在飞行前，请检查您电池情况，若有低电压，电池损坏等情况，请您停止操作并马上更换电池。
● Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found low voltage
or damage to battery.
● 机身内部设备连接的方式，会和您的收发设备有关，在一些功能更多的收发设备上，您可以通过设置简化机身内部设备的连接。详细
请查看您的收发设备以确认是否满足您需要的功能。
● The way the internal devices of the fuselage are connected will be related to your transmitter-receiver device. For those
transmitter-receiver devices with more functions, you can simplify the connection of the internal devices of the fuselage.
Check your device for details to see if it meets the features you need.
● 动力设备和收发设备第一次配对时，可能需要设置油门最大行程，请您自行设置。
● When the power system and transmitter-receiver device are paired for the first time, you may need to set the maximum
stroke of the throttle. Please set it yourself.
飞行前的建议
PRE-FLIGHT CHECKS
http://www.dwhobby.com/
工具
Tools Needed
飞行参数
Specification
翼展:1.62M（63.8"）
机长:1.25M（49.2"）
起飞重量: ≈3.1kg
Wingspan:1.62M（63.8"）
Fuselage Length:1.25M（49.2"）
Fly weight:≈3.1kg
推荐配置
Suggested Equipment
Motor : 3520-4220 800-500KV
Prop : 14inch
ESC：60-80A（4S）
Battery：4S 2200-4000mAh
Servo : 17g*4pcs
Radio：4CH+
马达：3520-4220 800-500KV
桨叶：14inch
电调：60-80A（4S）
电池：4S 2200-4000mAh
舵机：17g*4pcs
通道：4CH+



2
1
Use epoxy adhesive
★装配提示符号
Assembly symbol guide
Ensure free rotation Use medium CA Use a pencil
确保自由转动 使用适量快干胶粘固 用铅笔做记号
Use thin CA
使用少量快干胶粘固
用力推入
Push tightly Use hobby knife with
用模型刀切割
OIL
Apply Oil
加润滑油
Fully Tighten
拧紧安装
Apply threadlock
涂抹螺丝胶
Assemble right
and left
左右对称安装 使用环氧胶粘固
Epoxy glue
Repeat multiple times
重复拼装
x2
01 Assemble the Landing Gear
起落架安装
01-1
01-2
01-3
02 Assemble the Tail Wing and Tail Wheel
尾翼及尾轮安装
螺丝
Screw
M3x10mm
螺母+丝杆
Nut+Screw rod
轮轴套+螺母+自锁螺母
Wheel axle sleeve+Nut+Self-locking nut
配件图仅做参考用，您收到的实物可能因为修改/优化的原因导致与图片有略有不同。
Photos shown here just for reference, the product you received maybe slightly
differ from the photos due to continuous improvement on products.
SCG42-B:上机翼 Upper Wing
SCG42-D:起落架 Landing Gear
SCG42-F:水平尾翼 Horizontal tail/垂直尾翼 Vertical tail
SCG42-E:机翼支架 Wing bracket
K:PVC 风挡 PVC window shield
SCG42-G:尾轮组 tail wheel set
舵角 Rudder horn
连杆 Connecting rod
拉线 Stay wire
木块，木杆 Wood block; Wood rod
SCG42-A:机身 Fuselage
SCG42-H：
SCG42-J：螺丝及配件 screws & parts
SCG42-C:下机翼 Lower Wing
SCG42-A
SCG42-C
SCG42-E
SCG42-F
SCG42-F
SCG42-H
SCG42-H
SCG42-G SCG42-J
I
K
SCG42-D
SCG42-B
SCG42-B
02-3
02-4 02-5
02-1
02-2
Epoxy glue
1mm
X2
X2
X4
1 2 3
M6x375mm 丝杆
按图示顺序安装轮轴套与螺母
Install the wheel axle sleeve and nut in the
sequence shown in the figure
Screw rod
按图示在尾翼舵面上安装纸合页，并把
两个舵面通过U型钢丝连接起来。
Install paper hinges on the tail
control surface as shown in the
figure, and connect the two control
surfaces with U-shaped steel wires.
把舵面通过纸合页与尾翼连接，调整间
隙后纸合页处用CA胶粘合，并保持舵面
可以自由转动。
The control surface is connected
with the tail wing through the paper
hinge. After adjusting the clearance,
the paper hinge is fixed with CA
adhesive and the control surface
can rotate freely.
尾翼反面切除部分蒙皮，方便后
续粘合。
Part of the covering film on
the reverse side of the tail
wing is cut off to facilitate
subsequent bonding.
安装垂直尾翼与水平尾翼到机身尾翼，
调整到相互垂直后，用CA胶粘固。
Install the vertical tail and horizon-
tal tail to the fuselage tail, adjust
them to be perpendicular to each
other,
and then use CA glue to fix them.
像真机枪 Dummy machine gun
排气管 Exhaust pipe
瞄准器 Collimator



43
03 Wing installation
机翼安装
螺丝处钻孔点少量CA胶，再拧入螺丝。
A small amount of CA glue is drilled at
the screw, and then fix with screw.
安装机翼支架，调整到图示角度， 并注意安装顺序。
Install the wing brackets, adjust them to the angle shown
in the figure, and pay attention to the installation
sequence.
02-6 02-7
02-8
02-9
螺丝M3*15mm
Screw
Epoxy glue
1mm
尾轮穿出
tail wheel goes
through here
自攻螺丝
Self-tapping screw
M2x10mm
机头
Nose
长 Long
长 Long
短 Short
短 Short
X4
X6
X2
03-1
03-2
03-3 03-4
03-5 03-6
03-7 03-8
03-9 03-10
安装部分像真件 Installation of dummy parts
安装像真排气管
Install the dummy exhaust pipe.
安装风挡、像真瞄准器
Installation of windshield and
dummy collimator
安装像真机枪
Install the dummy
machine gun
插入预留孔，少量CA胶粘固。
Insert into the reserved hole
and fix with a small amount
of CA glue.
注意：上下机翼舵面均
按03-9、03-10步骤安
装，左右相同安装。
Note: The upper and
lower wing control
surfaces shall be
installed according
to steps 03-9 and
03-10,
and the left and
right wing control
surfaces shall be
installed the same.
支架装入预留孔，少量CA胶粘固，左右
相同安装。
The bracket is installed into the
reserved hole, and a small amount of
CA glue is used for fixing.
The left and right sides are installed
the same.
如图安装排气管，左右相同安装。
Install the exhaust pipe as shown in
the figure, with the same installation
on the left and right
自攻螺丝
Self-tapping screw
M2x10mm
自攻螺丝
Self-tapping screw
M2x10mm
碳杆 Φ6
碳管 Φ6x100mm
Carbon tube
碳管 Φ10x525mm
Carbon tube
碳管 Φ6x100mm
Carbon tube
Epoxy glue
安装转向舵到尾
翼，调整间隙后
用CA胶粘合连
接处纸合页。保
持舵面可以自由
转动。
Install the
steering
rudder to the
tail wing. After
adjusting the
clearance, glue
the paper
hinge at the
joint with CA
glue.
Keep the
control surface
free to rotate.
carbon rod


65
在舵面预留孔内安装舵角，在舵臂上安装快装接头，通
过钢丝连接连接舵臂与舵角。
Install the control horn in the reserved hole on the
rudder surface, install the EZ-connector on the
rudder arm, and connect the rudder arm with the
control horn through the steel wire.
机翼支架安装到上下机翼之间，插入机翼上的预留孔，连接处用环氧胶粘固。
安装支架时注意调整方向。
The wing bracket is installed between the upper and lower wings,
inserted into the reserved hole on the wing, and the joint is bonded
with epoxy adhesive.
Pay attention to the adjustment direction when installing the bracket.
在图示舵机位置安装舵机，舵臂上安装快装接头，升降舵和方向舵预留孔处安装
舵角，把舵机与舵角用钢丝连杆连接。
Install the servo at the servo position shown in the figure, install the
EZ-connecor on the rudder arm, install the control horn at the reserved
hole of elevator and rudder,
and connect the servo and control horn with steel wire connecting rod.
旋转夹头调整联动连杆的长度，结
合03-17的距离调整到合适长度，
然后安装。
Rotate the collet to adjust the
length of the linkage rod,
and adjust it to a proper length
in combination with the
distance of 03-17, and then
install it.
04 Installation of control servos for horizontal tail and vertical tail
水平尾翼，垂直尾翼控制舵机安装
03-11 03-12 03-13
03-14
03-16
03-17
下机翼舵机安装
Installation of lower
wing servo
舵机线穿出
Servo wire goes
through here
舵机线导入孔
servo wire lead-in hole
Epoxy glue
Epoxy glue
Epoxy glue
Epoxy glue
Epoxy glue
Epoxy glue
03-15 细节2 Detail 2
细节1
Detail 1
细节1 Detail 1
细节2
Detail 2
下机翼背面
Back of lower wing
上机翼背面
Back of upper wing
钢丝连杆
steel wire linkage rod
舵角
control horn
舵角
control horn
舵角
control horn 舵角
control horn
快装接头
EZ-connecor
快装接头
EZ-connecor
快装接头
EZ-connecor
快装接头
EZ-connecor
手拧螺丝 M4x10mm
Hand screw
X2
手拧螺丝 M4x10mm
Hand screw
X2
钢丝连杆
X4
碳杆Φ6x100mm
Carbon tube
碳管Φ10x275mm
Carbon tube
机翼安装到机身，并
注意几处安装细节。
Install the wing onto
the fuselage, and
pay attention to
several installation
details.
左右各一个
One on the left
and one on the right
在舵面的预留孔上安装舵角，用03-16调
整好的钢丝连杆连接上下机翼的舵面，并
保持可以联动。
Install the control horn on the reserved
hole of the control surface,
connect the upper and lower wing
control surfaces with the 03-16
adjusted steel wire connecting rod,
and keep them linked.
舵角
control horn
快装接头
EZ-connecor
steel wire linkage rod



8
7
05 Install the motor and cowling
安装马达及机头罩
06 Install the stay wire
机翼拉线安装
安装桨叶，用桨夹固定。
Install the propller and fix with adapter.
结合05-4,05-6两个步骤，根据马达尺寸调整马达座位置，调整好后用环氧胶粘固马达座。
In combination with steps 05-4 and 05-6, adjust the position of the motor base
according to the size of the motor, and then use epoxy adhesive to fix the motor base.
注意：马达座已设计右拉和下拉角度。
Note: The motor base has been designed with right pull and pull down angles.
07 Set and Adjust
设置和调试
重心位置展示
Display the C.G C.G
≈105mm
05-1 05-2 05-3
05-4 05-5 05-6
1
2
3
4
5
6
7
8
自攻螺丝
Self-tapping screw
M2x10mm
X2
X2
螺丝M2*10mm+ 螺母
Screw+Self-locking nut
安装部分像真件 Installation of dummy parts
像真机枪 dummy machine gun
自攻螺丝
Self-tapping screw
M3x15mm
自攻螺丝
Self-tapping screw
M2x10mm
细节1 Detail 1
细节1 Detail 1
细节2 Detail 2
细节2 Detail 2
细节3 Detail 3
细节3 Detail 3
细节1 Detail 1
在细节2，3预留的螺丝孔中点入少
量CA胶，再如图安装自攻螺丝及相
关扣具。
Insert a small amount of CA glue
into the reserved screw holes in
Details 2 and 3, and then install
the self-tapping screws and
relevant fasteners as shown in
the figure.
机翼拉线为一条，按数字顺序进行穿线安装。从1处开始，在8处结束。
安装时注意几处安装细节。
There is one wing stay wire, which shall be threaded and installed
in numerical order. Start at 1 and end at 8.
Pay attention to several installation details during installation.
拉线 Stay wire
1→2→3→4→5→6→7→8



10
9
更多电子设备调试细节可参考以下链接查看（可直接扫二维码）
More details about power system adjustment, please refer
to below link: (You can scan QR Code directly.)
http://www.dwhobby.com/art/connection
Elevator
升降舵
方向舵
副翼
AileronRudder
遥控器动作 飞机反应
升降杆下拉
Direction rod to the left
升降杆上推
Direction rod to the right
Steering rod to the left
Steering rod to the right
Lifting rod up
Lifting rod down
转向杆向右
转向杆向左
方向杆向右
方向杆向左
Control Directions Tests
地面控制方向测试
常规飞行(Normal Flying) 3D飞行 部分飞机支持(3D Flying only support some models)
副翼 Aileron ±（15°-30°） ±40° 或者更大(or larger)
平尾 Elevator ±15° ±40° 或者更大(or larger)
垂尾 Rudder ±15° ±40° 或者更大(or larger)
常用襟翼 Flap （起飞 take-off）15°-20° （降落 Landing）20°-40°
部分特殊机型会有V型尾翼，襟翼，前缘机翼或舵面很小等，可以以常规飞行的角度作为参考，在您不确认且没有有经验人员指导
的情况下，我们建议您先以小角度试飞以确认您的设置是否正确。
Some special models will have V-tails, flaps, leading edge wings, etc., which can be used as a reference for conventional
flight angles. If you do not confirm and there is no experienced person to guide you, we recommend that you first test
at a small angle to confirm that your settings are correct.
Rudder
Elevator
Aileron
20°-35°
25°
25°
25°
25°
20°-35°
通常情况下，舵面角度的设置如下：
Usually, the control throws set as below:
≈105mm
升降舵
副翼
方向舵
C.G