Dancover Titanium Tent User manual

12-12-2016
6x12x3,5x5,5m
Manual
for
Titanium Tent

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is your
responsibility to comply with local rules and regulations and to ensure that the marquee/tent is
assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is safely
secured and that the marquee/tent does not cause damage to others.
Do not use open re, welding equipment or other sources which can ignite, inside or close to the
tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent with
straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow, always remove snow from the roof of the marquee/tent regularly to prevent
snow from building on the roof, as heavy snow can cause the marquee/tent to collapse.
In the event of rain, there is a risk of rain puddles building up on top of the roof of the marquee/
tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility to ensure rain
puddles do not build up. As a precaution, make sure the roof of the marquee/tent is stretched
out properly and adequately over the side frames of the marquee/tent and remove rain water
regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of temperatures
below zero, always unpack and repack your marquee/tent indoors to avoid the risk of cracking
parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Note: Marquees are intended for events and other arrangements and are as such only meant for
short term temporary assembly and the following disassembly. Dancover warranty applies only
to the normal use of the Product, normal wear and tear excepted, in accordance with written
use instructions or manual. The warranty does not apply to damage caused by accident, abuse,
misuse, or modication of the Product.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manual.

Assembly Procedures
ground condition is suitable.
roof tubes to them accordingly.
3. Make each group of frame straight and assemble the roof purlins and horizontal walls in turn.
Make sure that all screws are tightened enough.
4. Assemble the cross tubes in front and back wall including the tensioning tube for covers at the
bottom.
roof cover onto the bottom tensioning tubes at the both side of frame as per Figure 5.
6. Then please put the rope in the sleeves at the two ends of roof cover into rings on the base
the bottom of the covers to the bottom tensioning tubes.
8. Please connect and tighten ropes between roof cover and front & back cover.
Your assembly is complete.
I

Assembly Illustration
For “user friendly” assembly we have
identified each individual component
with our partcode number as indicated
in the part list.
Please refer to the part code number
and drawings to ensure problem free
assembly.

Part No. Description Qty(pcs)
1 Curved Roof Tube (top) at two ends &tube size:1148mm 2
2 Curved Roof Tube (top) in the middle &tube size:1148mm 10
3 Straight Roof Tube at two ends &tube size:1787mm 4
4 Straight Roof Tube in the middle &tube size:1787mm 10
5 Curved Roof Tube (side) at two ends &short tube:660mm,long tube:1400mm 4
6 Curved Roof Tube (side) in the middle &short tube:660mm,long tube:1400 mm 10
7 Sidewall(in the middle) with base flange &tube size:2100mm 10
8 Sidewall(at two ends) with base flange &tube size:2100mm 4
9A-1 Upper Standing Legs in front panel &tube size:2124mm 2
9A-2 Upper Standing Legs in back panel &tube size:2124mm 2
9A-3 Upper Standing Legs in back panel(middle leg) &tube size:1398mm 1
9A-4 Middle Standing Legs in back panel(middle leg) &tube size:1900mm 1
9B Lower Standing Legs with base flange in front and back panel &tube size:2100mm 4
9C Lower Standing Legs with base flange in back panel( middle leg) &tube size: 2100mm 1
10 Roof purlin and horizon wall at both sides &tube size:1912mm 102
11A Cross tube(at two ends) in front and back panel &tube size:1138mm 12
11A-1 Cross tube(middle) in back panel &tube size:1662mm 6
11B Cross tube(middle) in front and back panel &tube size:1703.5mm 2
12A Tensioning cross tube in top roof &tube size :2180mm 6
12B Door dropping tube &1850mm 2
13 Slant supporting tube &2095mm 12
14 Roof cover 1
15 Front cover 1
16 Back cover 1
17 Stake peg &Dia 16x700mm 38
18 Rope for fixing cover
19 Bolts with nuts M14x30 228
M14x70 48
M12x50 4
M14x50 24
20 Inner join for cross tubes tubes &tube size:178mm 1
21 Inner join for part 11B and part 12B &tube size:400mm 1
Part List (W6xL12xSidewall3.5xH5.5M) with 3.5x3.5M machining door
12-12-2016

6
5
4
2
1
P a r t No.D i agr a m Q t y Par t N o . Diagram
3
7
8
9A-1
9 A - 2
4
4
2
4
1 0
11A1 2
9 C
6
11A-1
11B2
12A
12B2
1 3 1 2
Roof/Front/Ba c k cove r
14.15.16
1 7
R o p e forfixing c o ver
1 8
1 9
2 0
M 1 4 X30
M 1 4 X70
M 1 2 X50
M14X50
2 1 1
1
Q t y
W6XL12XS3.5XH5.5M(with3.5X3.5machiningdoor)
1 0
1 0
1 0
102
6
3 8
228
4 8
4
2 4
1 0
2
2
9A-3
9 B
1
1
9A-4
4
1
12-12-2016

2M
6M
12M
6x12x3.5x5.5M
Schematic drawing of placement for base flange

10 19
13
3
5
9B
11A
11B
14
12A 2
10
9A-2 11A-1
9A-3
9C
9C
7
6
13
8
6x12x3.5x5.5M
Frame Sketch
M14x50 bolt with nut

19
19 19
1-2
3-4
5-6
7－8
11B 20
6x12x3.5x5.5M
slant supporting tube
M12x50 bolt with nut
M12x50 bolt with nut
M14x70 bolt with nut
Frame installation procedure
And connection hint

11A
10
19
19
Frame connection hint
M14x30 bolt with nut