Dancover PRO XL User manual

16-12-2019
Manual
for
Storage Tent PRO
4m Series PVC/PE

Safety Advice
Attention
In some countries approval is needed to set up a tent larger than 75 m2. It is your responsibility
to comply with local rules and regulations and to ensure that the tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the tent is safely secured
and that the tent does not cause damage to others.
Do not use open re, welding equipment or other sources which can ignite, inside or close to the
tent.
The tent must be safely secured. We recommend you secure your tent with straps and pegs as
soon as it is assembled.
Make sure to check if the tent is covered by your home contents insurance.
Tents must be evacuated under extreme weather conditions.
In the event of snow, always remove snow from the roof of the tent regularly to prevent snow
from building on the roof, as heavy snow can cause the tent to collapse.
In the event of rain, there is a risk of rain puddles building up on top of the roof of the tent.
Heavy rain puddles can cause the roof to collapse. It is your responsibility to ensure rain
puddles do not build up. As a precaution, make sure the roof of the tent is stretched out
properly and adequately over the side frames of the tent and remove rain water regularly.
Do not unpack or repack your tent in freezing temperatures. In case of temperatures below
zero, always unpack and repack your tent indoors to avoid the risk of cracking parts.
The tent must be totally dry before you repack and store it to avoid mildew.
Note: Dancover warranty applies only to the normal use of the Product, normal wear and tear
excepted, in accordance with written use instructions or manual. The warranty does not apply
to damage caused by accident, abuse, misuse, or modification of the Product.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manual.

Warning
1. In order to avoid being rusted by air, oil is covered on the surface of the pipes. Before setting
up the tent, please remove the oil carefully rst to keep the cover clean.
2. Take note that the tent needs to be handled carefully to avoid damage.
3. Do not force the frames as they may be damage in the process.
4. Tents are meant as temporary shelter, and must be evacuated under extreme weather
conditions.
Please, select a suitable site for the tent to avoid the damage of underground sprinkler systems,
water, gas or electrical lines.

Part no. 4x10m
1Middle leg
1600mm 50-50 4
2Frame pole
1880mm 38-38 39
3Frame pole
1780mm 50-50 12
4Frame pole
2030mm 50-50 8
5Ceiling rail
2025mm 32-32 2
6Diagonal support
1720mm 32-32 6
7Roof support
1715mm 25-25 6
8Frame pole
2030mm 50-50 4
9Diagonal support
800mm 32-32 4
10 Female doorbar
2025mm 32-32 2
11 Lower leg
1600mm 50-50 8
12 Strengthen bar
1480mm 32-32 2
13 Strengthen bar
1845mm 32-32 2
A3-way connector
54-42/3 rings 6
B4-way connector
54-42/4 rings 12
4x12m
6
46
14
10
2
6
7
4
4
2
8
2
2
6
15
16-12-2019

Part no. 4x12m4x10m
14 3-way conntector
54-42 4
15 4-way connector
54-42 10
16 3-way connector
for corner 2
17 3-way connector
for corner 2
18 3-way connector
for sidewall 10
19 2-way connector
for endwall 2
20 Ceiling rail
1430mm 32-32 2
21 Bracket 14
22 Groundbracket 12
23 Strengthen bar
1855mm 25-25 24
24 Turnbuckle for
door 5130mm 4
25 Turnbuckle for
roof 2840mm 24
26 Turnbuckle for
side 3870mm 24
4
8
2
2
8
2
2
12
10
20
4
20
20
16-12-2019

Part no. 4x12m4x10m
27 Peg
10x350mm 24
28 Spiral peg 4
29 Small peg 50
30 Bungeeball long 60
31 M6 wingnut 26
32 Screw
M6x30mm 14
33 Screw
M6x45mm 10
34 Screw
M6x65mm 2
35 M6 nut 4
36 Spanner 2
37 Tie down 4
38 Steel clip 82
39 Screw
M8x50mm 92
40 Screw
M8x65mm 92
41 M8 nut 184
42 Peg
16x600mm 22
43 M12 washer 4
20
4
44
60
24
12
10
2
4
2
4
70
78
80
158
18
4
16-12-2019

Part no. 4x12m4x10m
44 M12 nut 4
45 Screw
M12x48mm 2
46 Screw
M12x65mm 2
47 Sheaved block
1 wheel 2
48 Sheaved block
2 wheel 2
49 Ratchet stape 4
50 Roof 1
51 Endwall 2
4
2
2
2
2
4
1
2
16-12-2019

Part 33 Part 34 Part 35 Part 43 Part 44 Part 45 Part 46
M6x45
Screw
M6x65
Screw
M6
Nut
M12
Washer
M12
Nut
M12x48
Screw
M12x65
Screw
4x10 4x12 4x10 4x12 4x10 4x12 4x10 4x12 4x10 4x12
Used for Part 7 and Part 21 12 14
Used for Part 6 and Part 20 2
Used for Part 5 and Part 10 2
Used for Part 6 and Part 9 4
Used for Sheaved block 1wheel Part 47 2 2 2
Used for Sheaved block 2 wheel Part 48
2 2 2
Used for M6x30 12 14
Used for M6x45 10 10
Used for M6x65 2 2
Used for 2-way connector 19 4 4
Used for 3-way connector A 6 6 12 12
Used for 4-way connector B 24 30 24 30
Used for 3-way connector 14 4 4 8 8
Used for 3-way connector 16 4 4 2 2
Used for 3-way connector 17 4 4 2 2
Used for 3-way connector 18 16 20 8 10
Used for 4-way connector 15 16 20 16 20
Used for Part 6 and Part 11 4 4
Used for Part 9 and Part 11 4 4
Used for M8x50 78 92
Used for M8x65 80 92
Used for M12x48 2 2
Used for M12x65 2 2
24 26 12 14 10 2 4 78 92 80 92 158 184 4 4 2 2
M8
Nut
4x10-12x3.5m storage pro
Part 31 Part 32 Part 39 Part 40 Part 41
M6
Wing nut
M6x30
Screw
M8x50
Screw (Ø42)
M8x65
Screw (Ø54)
16-12-2019

I
tubes, tent and accessories... etc. are present and the same as the list.
Assemble the framework of rooftop by joining the portion (A, B) together with poles (2, 4, 8) NO. 11
is on four corners for diagonal pipe.
II
across through each section as below.
III
Attach one end of supported pole (3) to the joints.
If you want the rope pull at the opposite side
than shown in the drawing then switch
sheaved block (47) and (48)
47
48
6

IV
Attach the other supported poles (1, 2, 11) to the joints, built-up the framework. NO. 11 is on four
corners for diagonal pipe.
V
You facilitate the assembly and dismantling by pulling the roof with ropes on tent frame. Use the
steel clips to fasten the cover to the frame. Each section we offer bracket and nail to fasten the
frame to ground.
48
47
6
6
5
5