Danfoss VLT CDS 803 User manual

MAKING MODERN LIVING POSSIBLE
Quick Guide
VLT®Compressor Drive CDS 803
www.danfoss.com/drives

Contents
1 Quick Guide 2
1.1 Safety 2
1.1.1 Warnings 2
1.1.2 Safety Instructions 2
1.2 Introduction 3
1.2.1 Available Literature 3
1.2.2 Approvals 3
1.2.3 IT Line Power 3
1.2.4 Avoid Unintended Start 3
1.2.5 Disposal Instruction 3
1.3 Installation 4
1.3.1 Before Starting Repair Work 4
1.3.2 Enclosure Types 4
1.3.3 Side-by-Side Installation 4
1.3.4 Dimensions 5
1.3.6 Connecting to Line Power and Compressor 6
1.3.7 Fuses 8
1.3.8 EMC-compatible Electrical Installation 9
1.3.9 Control Terminals 10
1.4 Programming 12
1.4.2 The Start-up Wizard 13
1.4.3 Main Menu Structure 23
1.5 Acoustic Noise or Vibration 25
1.6 Warnings and Alarms 25
1.7 General Specifications 26
1.7.1 Line Power Supply 3x200–240 V AC 26
1.7.2 Line Power Supply 3x380–480 V AC 27
1.8 Special Conditions 31
1.8.1 Derating for Ambient Temperature and Switching Frequency 31
1.8.2 Derating for Low Air Pressure 31
1.9 Options for VLT®Compressor Drive CDS 803 31
Contents Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved.

1 Quick Guide
1.1 Safety
1.1.1 Warnings
WARNING
High Voltage Warning
The voltage of the adjustable frequency drive is
dangerous whenever it is connected to line power.
Incorrect installation of the compressor or adjustable
frequency drive may cause damage to the equipment,
serious injury or death. Consequently, it is essential to
comply with the instructions in this manual as well as
local and national rules and safety regulations.
WARNING
DISCHARGE TIME!
Adjustable frequency drives contain DC link capacitors
that can remain charged even when the adjustable
frequency drive is not powered. To avoid electrical
hazards, disconnect AC line power, any permanent
magnet type compressors, and any remote DC link
power supplies, including battery backups, UPS, and DC
link connections to other adjustable frequency drives.
Wait for the capacitors to fully discharge before
performing any service or repair work. The waiting time
is listed in the Discharge Time table. Failure to wait for
the specified period of time after power has been
removed to do service or repair could result in death or
serious injury.
Voltage [V] Cooling capacity [TR] Minimum waiting time
(min)
3x200 4–6.5 15
3x400 4–5 4
3x400 6.5 15
Table 1.1 Discharge Time
CAUTION
Leakage Current
The ground leakage current from the adjustable
frequency drive exceeds 3.5 mA. cross-sectionAccording
to IEC 61800-5-1, a reinforced protective ground
connection must be ensured with a min. 10 mm2 Cu or
an additional PE wire - with the same cable cross-section
as the line power wiring - must be terminated
separately.
Residual Current Device
This product can cause a DC current in the protective
conductor. Where a residual current device (RCD) is used
for extra protection, only an RCD of Type B (time
delayed) shall be used on the supply side of this
product. See also Danfoss Application Note on RCD,
MN90G.
Protective grounding of the adjustable frequency drive
and the use of RCDs must always follow national and
local regulations.
WARNING
Installation at High Altitudes
For altitudes above 6,600 feet [2 km], contact Danfoss
regarding PELV.
1.1.2 Safety Instructions
•Make sure the adjustable frequency drive is
properly connected to ground.
•Do not remove AC line input connections,
compressor connections or other power
connections while the adjustable frequency drive
is connected to power.
•Protect users against supply voltage.
•Protect the compressor against overloading
according to national and local regulations.
•The ground leakage current exceeds 3.5 mA.
•The [Off/Reset] key is not a safety switch. It does
not disconnect the adjustable frequency drive
from line power.
Quick Guide Quick Guide
2 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

1.2 Introduction
1.2.1 Available Literature
This Quick Guide contains basic information necessary for
installing and running the adjustable frequency drive.
Supplementary publications and manuals are available
from Danfoss. See www.danfoss.com/BusinessAreas/DrivesSo-
lutions/ Documentations/VLT+Technical+Documentation.htm
for listings.
1.2.2 Approvals
Certification IP20
EC Declaration of
Conformity ✓
UL-listed ✓
C-tick ✓
Table 1.2 Approvals
The adjustable frequency drive complies with UL508C
thermal memory retention requirements. For more
information, refer to the section Motor Thermal Protection
in the Design Guide.
1.2.3 IT Line Power
CAUTION
IT Line Power
Installation on isolated line power source, that is, IT line
power.
Max. supply voltage allowed when connected to line
power: 440 V (3x380–480 V units).
Open the RFI switch by removing the screw on the side of
the adjustable frequency drive when at IT grid.
130BB612.10
1
1RFI switch
Figure 1.1 IP20
CAUTION
If reinserted, only use M3x12 screws.
1.2.4 Avoid Unintended Start
While the adjustable frequency drive is connected to line
power, the compressor can be started/stopped using
digital commands, bus commands, references or via the
LCP.
•Disconnect the adjustable frequency drive from
line power whenever personal safety consider-
ations make it necessary to avoid unintended
start of any compressors.
•To avoid unintended start, always press [Off/
Reset] before changing parameters.
1.2.5 Disposal Instruction
Equipment containing electrical components
may not be disposed of together with domestic
waste.
It must be separately collected with electrical
and electronic waste according to local and
currently valid legislation.
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 3
11

1.3 Installation
1.3.1 Before Starting Repair Work
1. Disconnect from line power (and external DC
supply, if present).
2. Wait as stated in Table 1.1 for discharge of the DC
link.
3. Remove compressor cable.
1.3.2 Enclosure Types
Cooling capacity 400 V IP20
Enclosure
4 TR/VZH028 H3
5 TR/VZH035 H3
6.5 TR/VZH044 H4
Table 1.3 H3-H4, 400 V
Cooling capacity 200 V IP20
Enclosure
4 TR/VZH028 H4
5 TR/VZH035 H4
6.5 TR/VZH044 H5
Table 1.4 H4-H5, 200 V
1.3.3 Side-by-Side Installation
The adjustable frequency drive can be mounted side-by-
side and requires the clearance above and below for
cooling.
Frame IP class Clearance above/below mm/[inch]
H3 IP20 100/4
H4 IP20 100/4
H5 IP20 100/4
Table 1.5 Clearance
NOTICE!
With IP21/Nema Type1 option kit mounted, a distance of
2 in [50 mm] between the units is required.
Quick Guide Quick Guide
4 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

1.3.4 Dimensions
NOTICE!
The figure in Table 1.6 is with LCP but all dimensions are the same without LCP.
A
a
b
B
C
D
130BB614.10
e
f
a
e
130BC246.10
Enclosure Height (in [mm]) Width (in [mm]) Depth (in
[mm])
Mounting hole (in [mm]) Max.
Weight
Frame IP Class A A1) a B b C d e f lb [kg]
H3 IP20 10 [255] 13 [329] 9.5 [240] 3.9 [100] 2.9 [74] 8.1 [206] 0.4
[11]
0.2 [5.5] 0.3
[8.1]
9.9 [4.5]
H4 IP20 11.7 [296] 14.1 [359] 10.8 [275] 5.3 [135] 4.1 [105] 9.5 [241] 0.5
[12.6]
0.3 [7] 0.33
[8.4]
17.4 [7.9]
H5 IP20 13.2 [334] 15.8 [402] 12.4 [314] 5.9 [150] 4.7 [120] 10 [255] 0.5
[12.6]
0.3 [7] 0.34
[8.5]
21 [9.5]
Table 1.6 Dimensions
1) Including decoupling plate
The dimensions are only for the physical units, but when installing in an application it is necessary to add space for free air
passage both above and below the units. The amount of space for free air passage is listed in Table 1.5.
1.3.5 Electrical Installation in General
All cabling must comply with national and local regulations on cable cross-sections and ambient temperature. Copper
conductors required, (167 °F [75 °C]) recommended.
Enclosure Torque [Nm]
Frame IP class Line Compressor
connection
DC connection Control
terminals
Ground Relay
H3 IP20 1.4 0.8 0.8 0.5 0.8 0.5
H4 IP20 1.2 1.2 1.2 0.5 0.8 0.5
H5 IP20 1.2 1.2 1.2 0.5 0.8 0.5
Table 1.7 Enclosure H3-H5
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 5
11

1.3.6 Connecting to Line Power and
Compressor
The adjustable frequency drive is designed to operate
Danfoss VZH Compressors. For the maximum cross-section
on wires, see chapter 1.7 General Specifications.
•Use a shielded/armored compressor cable to
comply with EMC emission specifications, and
connect this cable to both the decoupling plate
and the compressor metal.
•Keep compressor cable as short as possible to
reduce the noise level and leakage currents.
•For further details on mounting of the
decoupling plate, see VLT
®
Compressor Drive CDS
803 Decoupling Plate Installation Instructions.
•Also see EMC-compatible Installation in the
VLT
®
Compressor Drive CDS 803 Design Guide.
1. Mount the ground wires to ground terminal.
2. Connect compressor to terminals U, V and W, see
Table 1.8.
UT1
V T2
W T3
Table 1.8 Connection of Compressor to Terminals
3. Mount line power supply to terminals L1, L2 and
L3 and tighten.
130BB634.10
1
2
2
3
4
Motor
UVW-DC+DC
MAINS
1 Line
2 Ground
3 Compressor
4 Relays
Figure 1.2 H3-H5 Frame
IP20 200–240 V 4–6.5 tons
IP20 380–480 V 4–6.5 tons
Quick Guide Quick Guide
6 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

-DC+DC
BR- BR+ U V W
99
M A I N S
95
RELAY 1 RELAY 2
- LC +
130BA261.10
Figure 1.3 Mount the two screws in the mounting plate, slide
it into place and tighten fully
MOTOR
MOTOR
U V W
99
130BT302.12
Figure 1.4 H3-H5 Frame
130BA262.10
M
I N S
+DC
BR- BR+ UVW
RELAY 1 RELAY 2
95
Figure 1.5 When mounting cables, first mount and tighten
ground cable
130BA263.10
95
MAINS
+DC
BR- BR+ UVW
91 92 93
L1 L2 L3
RELAY 1 RELAY 2
Figure 1.6 Mount line power plug and tighten wires
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 7
11

+DC
BR- BR+ UVW
MAINS
L1 L2 L3
91 92 93
RELAY 1 RELAY 2
99
- LC -
130BA264.10
Figure 1.7 Tighten support bracket on line power wires
1.3.7 Fuses
Branch circuit protection
To protect the installation against electrical and fire hazard, all branch circuits in an installation, switch gear, machines, etc.,
must be short-circuit and overcurrent protected according to national and local regulations.
Short circuit protection
Danfoss recommends using the fuses listed in Table 1.9 to protect service personnel or equipment in case of an internal
failure in the unit or short circuit on the DC link. The adjustable frequency drive provides full short circuit protection in case
of a short circuit on the compressor.
Overcurrent protection
Provide overload protection to avoid overheating of the cables in the installation. Overcurrent protection must always be
carried out according to local and national regulations. Circuit breakers and fuses must be designed for protection in a
circuit capable of supplying a maximum of 100,000 Arms (symmetrical), 480 V maximum.
UL/Non-UL compliance
Use the fuses listed in Table 1.9 to ensure compliance with UL or IEC 61800-5-1.
NOTICE!
In the event of malfunction, failure to follow the protection recommendation may result in damage to the adjustable
frequency drive.
Fuse
UL Non-UL
Bussmann Bussmann Bussmann Bussmann Max fuse
CDS 803 Type RK5 Type RK1 Type J Type T Type G
3x200–240 V IP20
4 TR/VZH028 FRS-R-50 KTN-R50 JKS-50 JJN-50 50
5 TR/VZH035 FRS-R-50 KTN-R50 JKS-50 JJN-50 50
6.5 TR/VZH044 FRS-R-80 KTN-R80 JKS-80 JJN-80 65
3x380–480 V IP20
4 TR/VZH028 FRS-R-25 KTS-R25 JKS-25 JJS-25 25
5 TR/VZH035 FRS-R-25 KTS-R25 JKS-25 JJS-25 25
6.5 TR/VZH044 FRS-R-50 KTS-R50 JKS-50 JJS-50 50
Table 1.9 Fuses
Quick Guide Quick Guide
8 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

1.3.8 EMC-compatible Electrical Installation
General points to be observed to ensure EMC-compatible electrical installation.
•Use only shielded/armored motor cables and shielded/armored control cables.
•Connect the shield to ground at both ends.
•Avoid installation with twisted shield ends (pigtails), since this ruins the shielding effect at high frequencies. Use
the cable clamps provided instead.
•Ensure the same potential between adjustable frequency drive and ground potential of PLC.
•Use starwashers and galvanically grounding plates.
L1
L2
L3
PE
Min. 0.0248 in2[16 mm2]
Equalizing cable
Control cables
All cable entries in
one side of panel
Grounding rail
Cable insula-
tion stripped
Output con-
tactor, etc.
Motor cable
Motor, 3 phases and
PLC etc. Panel
Line power supply
Min. 7.9 in [200 mm]
between control
cable, line cable
and between line power
motor cable
PLC
Protective ground
Reinforced protective ground
130BB761.10
Figure 1.8 EMC-compatible Electrical Installation
For North America, use metal conduits instead of shielded cables.
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 9
11

1.3.9 Control Terminals
130BB622.10
Figure 1.9 Location of Control Terminals
1. Place a screwdriver behind the terminal cover to
activate the snap.
2. Tilt the screwdriver outwards to open the cover.
Control terminals
To make the compressor run:
1. Apply start signal on terminal 18.
2. Connect terminals 12, 27 and terminal 53, 54 or
55
18 19
12 20 55
27 29 42 45 50 53 54
DIGI IN DIGI IN DIGI IN DIGI IN
61 68 69
N P COMM. GND
+24V
0/4-20mA A OUT / DIG OUT 0/4-20mA A OUT / DIG OUT
GND
GND
10V/20mA IN 10V/20mA IN 10V OUT
130BB625.10
BUS TER.
OFF ON
Figure 1.10 Control Terminals
Set the functions of digital input 18, 19 and 27 in
5-00 Digital Input Mode (PNP is default value). Set the
function of digital input 29 in 5-03 Digital Input 29 Mode
(PNP is default value).
Quick Guide Quick Guide
10 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

1.3.10 Electrical Overview
L1
L2
L3
3 Phase
power
input
PE PE
+10 V DC
0-10 V DC-
0-10 V DC-
50 (+10 V OUT)
54 (A IN)
53 (A IN)
55 (COM A IN/OUT)
0/4-20 mA
0/4-20 mA
42 0/4-20 mA A OUT / DIG OUT
45 0/4-20 mA A OUT / DIG OUT
18 (DIGI IN)
19 (DIGI IN)
27 (DIGI IN)
29 (DIGI IN)
12 (+24 V OUT)
24 V (NPN)
20 (COM D IN)
O V (PNP)
24 V (NPN)
O V (PNP)
24 V (NPN)
O V (PNP)
24 V (NPN)
O V (PNP)
Bus ter.
Bus ter.
RS-485
Interface RS-485
(N PS-485) 69
(P RS-485) 68
(Com RS-485 ) 61
(PNP)-Source
(NPN)-Sink
ON=Terminated
OFF=Unterminated
ON
1 2
240 V AC 3 A
Not present on all power sizes
Do not connect shield to 61
01
02
03
relay1
relay2
UDC+
UDC-
Motor
U
V
W
130BD467.10
06
05
04
240 V AC 3 A
Figure 1.11 Basic Wiring Schematic Drawing
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 11
11

1.4 Programming
1.4.1 Local Control Panel (LCP)
NOTICE!
LCP is NOT supported in SW 1.0X!
The LCP is divided into four functional sections.
A. Display
B. Menu key
C. Navigation keys and LEDs
D. Operation keys and LEDs
130BB765.11
Com.
1-20 Motor Power
[5] 0.37kW - 0.5HP
Setup 1
A
B
1
12
13 14 15
11
11
10
9
8
7
6
5
4
3
2
C
D
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Reset
Auto
On
Alarm
Warn.
On
11
Back
O
Figure 1.12 Local Control Panel (LCP)
A. Display
The LCD display is backlit with two alphanumeric lines. All
data is displayed on the LCP.
Information can be read from the display.
1 Parameter number and name.
2 Parameter value.
3 Set-up number shows the active set-up and the edit set-
up. If the same set-up acts as both the active and edit set-
up, only that set-up number is shown (factory setting).
When active and edit set-ups differ, both numbers are
shown in the display (Set-up 12). The flashing number
indicates the edit set-up.
4 Compressor direction is shown to the bottom left of the
display – indicated by a small arrow pointing either
clockwise or counter-clockwise.
5 The triangle indicates if the LCP is in Status, Quick Menu
or Main Menu.
Table 1.10 Legend to Figure 1.12
B. Menu key
Press [Menu] to select between Status, Quick Menu or
Main Menu.
C. Navigation keys and LEDs
6Com LED: Flashes when bus communication is communi-
cating.
7 Green LED/On: Control section is working.
8 Yellow LED/Warn.: Indicates a warning.
9 Flashing Red LED/Alarm: Indicates an alarm.
10 [Back]: For moving to the previous step or layer in the
navigation structure
11 [▲] [▼] [►]: For navigating between parameter groups,
parameters and within parameters. Can also be used for
setting local reference.
12 [OK]: For selecting a parameter and for accepting changes to
parameter settings
Table 1.11 Legend to Figure 1.12
Quick Guide Quick Guide
12 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

D. Operation keys and LEDs
13 [Hand On]: Starts the compressor and enables control of
the adjustable frequency drive via the LCP.
NOTICE!
Terminal 27 Digital Input (5-12 Terminal 27 Digital
Input) has stop inverse as default setting. This
means that [Hand On] does not start the
compressor if there is no 24 V to terminal 27.
Connect terminal 12 to terminal 27.
14 [Off/Reset]: Stops the compressor (Off). If in alarm mode,
the alarm is reset.
15 [Auto On]: The adjustable frequency drive is controlled
either via control terminals or serial communication.
Table 1.12 Legend to Figure 1.12
1.4.2 The Start-up Wizard
The built-in wizard menu guides the installer through the
set-up of the adjustable frequency drive in a clear and
structured manner to set up an open-loop application. An
open-loop application is here an application with a start
signal, analog reference (voltage or current) and optionally
also relay signals (but no feedback signal from the process
applied).
FC
+24 V
DIG IN
DIG IN
DIG IN
DIG IN
COM DIG IN
A OUT/D OUT
A OUT/D OUT
18
19
27
29
42
55
50
53
54
20
12
01
02
03
04
05
06
R2 R1
+
0-10 V
Start
+10 V
A IN
A IN
COM
130BD872.10
45
Reference
15
PRESSURE SWITCH
Figure 1.13 Open-loop Application
The wizard is initially be shown after power-up until any
parameter has been changed. The wizard can always be
accessed again through the Quick Menu. Press [OK] to start
the wizard. Press [Back] to return to the status screen.
130BB629.10
Press OK to start Wizard
Push Back to skip it
Set-up 1
Figure 1.14 Start-up/Quit Wizard
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 13
11

English
OK
5
if
Select Language
... the CDS 803 Wizard starts
Size related
Select Grid Type
4
Select Main Menu Password 6
[0]
[0]
OK
B
a
c
k
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Reset Auto
On
Alarm
Warn.
On
Status Screen
The Wizard can always be
reentered via the Quick Menu!
Power Up Screen
At power up the user is
asked to choose the
prefered laguage.
Select language
[1] English
0.0 Hz
0.0 kW
Setup 1
Setup 1
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Reset Auto
On
Alarm
Warn.
On
Press OK to start Wizard
Press Back to skip it
Setup 1
Status Main
Menu
Quick
Menu
Hand
On
OK
Menu
Reset Auto
On
Alarm
Warn.
On
The next screen will be
the Wizard screen.
Wizard Screen
1
2
if
3
B
a
c
k
B
a
c
k
B
a
c
k
Com.
Com.
Com.
130BD873.12
Size related
Select Compressor Selection 7
200 Hz
Select Max. reference 8
Analog in 53
Select Reference 1 Source 9
[1]
30 s
Select Ramp 1 Ramp Up Time 10
30 s
Select Ramp 1 Ramp Down Time 11
Stop inverse
Select Terminal 27 Digital In 12
Alarm
Select Relay 1 13
Drive Running
Select Relay 2 14
0.07 V
Select Terminal 53 Low Voltage 15
10 V
Select Terminal 53 High Voltage 16
Digital and ctrl.word
Select Control Site 17
[0]
FC
Select Protocol 18
[0]
Setup 1
1
Select Address 19
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
[6]
[9]
[5]
Figure 1.15 Open-loop Applications
Quick Guide Quick Guide
14 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

The Start-up Wizard for open-loop applications
Parameter Option Default Function
0-01 Language [0] English
[1] Deutsch
[2] Francais
[3] Dansk
[4] Spanish
[5] Italiano
[28] Bras.port
[0] English Select the language for the display.
0-06 GridType [0] 200–240 V/50 Hz/IT grid
[1] 200–240 V/50 Hz/Delta
[2] 200–240 V/50 Hz
[10] 380–440 V/50 Hz/IT grid
[11] 380–440 V/50 Hz/Delta
[12] 380–440 V/50 Hz
[20] 440–480 V/50 Hz/IT grid
[21] 440–480 V/50 Hz/Delta
[22] 440–480 V/50 Hz
[30] 525–600 V/50 Hz/IT grid
[31] 525–600 V/50 Hz/Delta
[32] 525–600 V/50 Hz
[100] 200–240 V/60 Hz/IT grid
[101] 200–240 V/60 Hz/Delta
[102] 200–240 V/60 Hz
[110] 380–440 V/60 Hz/IT grid
[111] 380–440 V/60 Hz/Delta
[112] 380–440 V/60 Hz
[120] 440–480 V/60 Hz/IT grid
[121] 440–480 V/60 Hz/Delta
[122] 440–480 V/60 Hz
[130] 525–600 V/60 Hz/IT grid
[131] 525–600 V/60 Hz/Delta
[132] 525–600 V/60 Hz
Size related Select operating mode for restart upon
reconnection of the adjustable frequency
drive to AC line voltage after power-down.
0-60 Main Menu Password 0–999 0 Define the password for access to the LCP.
1-13 Compressor Selection [24] VZH028-R410A
[25] VZH035-R410A
[26] VZH044-R410A
Size related Select the used compressor.
3-03 Maximum Reference 0–200 Hz 200 Hz The maximum reference is the lowest
obtainable by summing all references.
3-15 Reference 1 Source [0] No function
[1] Analog in 53
[2] Analog in 54
[7] Pulse input 29
[11] Local bus reference
[1] Analog in 53 Select the input to be used for the reference
signal.
3-41 Ramp 1 Ramp Up Time 0.05–3600.0 s 30.00 s Ramp-up time from 0 to 1-25 Motor Nominal
Speed.
3-42 Ramp 1 Ramp Down Time 0.05–3600.0 s 30.00 s Ramp-down time from rated motor speed to
0.
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 15
11

Parameter Option Default Function
5-12 Terminal 27 Digital Input [0] No operation
[1] Reset
[2] Coast inverse
[3] Coast and reset inverse
[4] Quick stop inverse
[5] DC brake inverse
[6] Stop inverse
[7] External Interlock
[8] Start
[9] Latched start
[10] Reversing
[11] Start reversing
[14] Jog
[16] Preset ref bit 0
[17] Preset ref bit 1
[18] Preset ref bit 2
[19] Freeze reference
[20] Speed up
[22] Slow
[23] Set-up select bit 0
[34] Ramp bit 0
[52] Run permissive
[53] Hand start
[54] Auto-start
[60] Counter A (up)
[61] Counter A (down)
[62] Reset Counter A
[63] Counter B (up)
[64] Counter B (down)
[65] Reset Counter B
[6] Stop inverse Select the input function for terminal 27.
5-40 Function Relay [0] Function relay See 5-40 Function Relay Alarm Select the function to control output relay 1.
5-40 Function Relay [1] Function relay See 5-40 Function Relay Drive running Select the function to control output relay 2.
6-10 Terminal 53 Low Voltage 0–10 V 0.07 V Enter the voltage that corresponds to the low
reference value.
6-11 Terminal 53 High Voltage 0–10 V 10 V Enter the voltage that corresponds to the
high reference value.
8-01 Control Site [0] Digital and ctrl.word
[1] Digital only
[2] Controlword only
[0] Digital and
ctrl. word
Select if digital, bus, or a combination of both
should control the adjustable frequency drive.
8-30 Protocol [0] FC
[2] Modbus RTU
[0] FC Select the protocol for the integrated RS-485
port.
8-32 Baud Rate [0] 2,400 Baud [1]
4,800 Baud
*[2] 9,600 Baud
[3] 19,200 Baud
4] 38,400 Baud
5] 57,600 Baud
[6] 76,800 Baud
[7] 115,200 Baud
9600 Select the baud rate for the RS-485 port.
Table 1.13 Open-loop Applications Set-up
Quick Guide Quick Guide
16 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1

The Start-up Wizard for compressor functions
28-13 Boost Duration
60 s
5
6
28-01 Interval between Starts
130BD874.11
28-11 Low Speed Running Time
20 min
28-02 Minimum Run Time
3
28-00 Short Cycle Protection
[1] Enabled
1
28-10 Oil Return Management
[1] On
4
2
300 s
60 s
Figure 1.16 Compressor Function Wizard
Compressor function wizard
Parameter Option Default Function
28-00 Short Cycle Protection [0] Disabled
[1] Enabled
[1] Enabled Select if short cycle protection is to be used.
28-01 Interval between Starts 0–3600 s 300 s Enter the minimum allowed time between
starts.
28-02 Minimum Run Time 10–3600 s 60 s Enter the minimum allowed time to run
before stop.
28-10 Oil Return Management [0] Off
[1] On
[1] On Select if Oil Return Management is to be used.
28-11 Low Speed Running Time 1–1400 min 20 min Enter the low speed running time.
28-13 Boost Duration 10–3600 s 60 s Enter the boost duration for the oil return.
Table 1.14 Compressor Function
Quick Guide Quick Guide
MG18M122 Danfoss A/S © Rev. 08/2014 All rights reserved. 17
11

The Start-up Wizard for compressor closed-loop applications
6-24 Terminal 54 Low Ref./Feedb.
0
6-23 Terminal 54 High Current
6-22 Terminal 54 Low Current
4.00
6-15 Terminal 53 High Ref./Feedb.
200.000
6-10 Terminal 53 Low Voltage
0.07 V
6-11 Terminal 53 High Voltage
13
14
15
16
18
19
21
22
5-40 Function Relay 1
5-40 Function Relay 2
Drive running
130BD875.12
6-25 Terminal 54 High Ref./Feedb.
0-60 Main Menu Password
[0]
3
0-01 Language
[0] English
1
4
20-06 Grid Type
Size related
3-10 Preset Reference
0%
3-02 Minimum Reference
0 Hz
1-00 Conguration Mode
Size related
3-03 Maximum Reference
200
3-42 Ramp 1 Ramp Down Time
5
5-12 Terminal 27 Digital Input
3-41 Ramp 1 Ramp Up Time
5
6
7
8
9
10
11
12
3-15 Reference 1 Source
6-14 Terminal 53 Low Ref./Feedb.
30.000
17
20
8-30 Protocol
[0] FC
8-01 Control Site
20-04 Feedback 2 Conversion
20-00 Feedback 1 Source
0.00
23
24
26
27
8-31 Address
Digital and ctrl.word
25
[0]
Hz
Analog in 53
[1]
10 V
[0]
30.00
s
30.00
s
Stop inverse
[6]
mA
20.00 mA
4999.000
Analog input 54
[2]
Linear
[0]
1
1-13 Compressor Selection
Alarm
Closed loop
[1]
Hz
Hz
0.000
Figure 1.17 Closed-loop Wizard
Quick Guide Quick Guide
18 Danfoss A/S © Rev. 08/2014 All rights reserved. MG18M122
1
1