Danfoss VLT AQUA Drive FC 200 Operating instructions

Contents
1 How to Programme
3
How to operate graphical LCP (GLCP) 4
Display Mode 9
Display Mode - Selection of Displayed Variables 9
How to operate numeric LCP (NLCP) 11
Parameter Set-Up 13
2 Parameter Description 19
Main Menu - Operation and Display - Group 0 19
Main Menu - Load and Motor - Group 1 35
Main Menu - Brakes - Group 2 47
Main Menu - Reference/Ramps - Group 3 50
Main Menu - Limits/Warnings - Group 4 58
Main Menu - Digital In/Out - Group 5 63
Main Menu - Analog In/Out - Group 6 86
Main Menu - Communications and Options - Group 8 96
Main Menu - Profibus - Group 9 104
Main Menu - CAN Fieldbus - Group 10 113
Main Menu - Smart Logic - Group 13 119
Main Menu - Special Functions -Group 14 134
Main Menu - Frequency Converter Information - Group 15 143
Main Menu - Data Readouts - Group 16 150
Main Menu - Data Readouts 2 - Group 18 158
Main Menu - FC Closed Loop - Group 20 160
Main Menu - Extended Closed Loop - Group 21 170
Main Menu - Application Functions - Group 22 183
Main Menu - Time-based Functions - Group 23 198
Main Menu - Cascade Controller - Group 25 212
Main Menu - Analog I/O Option MCB 109 - Group 26 226
Main menu – Water application – Group 29 233
Main Menu - Bypass Option - Group 31 235
3 Parameter Lists 237
Parameter Options 237
Default settings 237
Operation/Display 0-** 238
Load/Motor 1-** 240
Brakes 2-** 242
Reference / Ramps 3-** 243
Limits / Warnings 4-** 244
VLT
®
AQUA Drive Programming Guide Contents
MG.20.O4.02 - VLT®is a registered Danfoss trademark 1

Digital In/Out 5-** 245
Analog In/Out 6-** 246
Comm. and Options 8-** 247
Profibus 9-** 248
CAN Fieldbus 10-** 249
Smart Logic 13-** 250
Special Functions 14-** 251
FC Information 15-** 252
Data Readouts 16-** 254
Data Readouts 2 18-** 256
FC Closed Loop 20-** 257
Ext. Closed Loop 21-** 258
Application Functions 22-** 260
Timed Actions 23-** 262
Cascade Controller 25-** 263
Analog I/O Option MCB 109 26-** 265
Cascade CTL Option 27-** 266
Water Application Functions 29-** 268
Bypass Option 31-** 269
Index
270
Contents VLT
®
AQUA Drive Programming Guide
2 MG.20.O4.02 - VLT®is a registered Danfoss trademark

1 How to Programme
VLT AQUA Drive
FC 200 Series
Software version: 1.33
This guide can be used with all FC 200 frequency converters with
software version 1.33 or later.
The actual software version number can be read from
par.15-43
Software Version .
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 3
1

1.1.1 How to operate graphical LCP (GLCP)
The following instructions are valid for the GLCP (LCP 102).
The GLCP is divided into four functional groups:
1. Graphical display with Status lines.
2. Menu keys and indicator lights (LED's) - selecting mode, changing parameters and switching between display functions.
3. Navigation keys and indicator lights (LEDs).
4. Operation keys and indicator lights (LEDs).
Graphical display:
The LCD-display is back-lit with a total of 6 alpha-numeric lines. All data is displayed on the LCP which can show up to five operating variables while in
[Status] mode.
Display lines:
a. Status line: Status messages displaying icons and graphics.
b. Line 1-2: Operator data lines displaying data and variables de-
fined or chosen by the user. By pressing the [Status] key, up to
one extra line can be added.
c. Status line: Status messages displaying text.
The display is divided into 3 sections:
Top section (a)
shows the status when in status mode or up to 2 variables when not in
status mode and in the case of Alarm/Warning.
The number of the Active Set-up (selected as the Active Set-up in par. 0-10) is shown. When programming in another Set-up than the Active Set-up, the
number of the Set-up being programmed appears to the right in brackets.
Middle section (b)
shows up to 5 variables with related unit, regardless of status. In case of alarm/warning, the warning is shown instead of the variables.
It is possible to toggle between three status read-out displays by pressing the [Status] key.
Operating variables with different formatting are shown in each status screen - see below.
Several values or measurements can be linked to each of the displayed operating variables. The values / measurements to be displayed can be defined
via par. 0-20, 0-21, 0-22, 0-23, and 0-24, which can be accessed via [QUICK MENU], "Q3 Function Setups", "Q3-1 General Settings", "Q3-11 Display
Settings".
Each value / measurement readout parameter selected in par. 0-20 to par. 0-24 has its own scale and number of digits after a possible decimal point.
Larger numeric values are displayed with few digits after the decimal point.
Ex.: Current readout
1 How to Programme VLT
®
AQUA Drive Programming Guide
4 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

5.25 A; 15.2 A 105 A.
Status display I
This read-out state is standard after start-up or initialization.
Use [INFO] to obtain information about the value/measurement linked to
the displayed operating variables (1.1, 1.2, 1.3, 2, and 3).
See the operating variables shown in the display in this illustration. 1.1,
1.2 and 1.3 are shown in small size. 2 and 3 are shown in medium size.
130BP041.10
1.1
1.3
2
1.2
3
Status display II
See the operating variables (1.1, 1.2, 1.3, and 2) shown in the display in
this illustration.
In the example, Speed, Motor current, Motor power and Frequency are
selected as variables in the first and second lines.
1.1, 1.2 and 1.3 are shown in small size. 2 is shown in large size.
130BP062.10
2
1.2
1.3
1.1
Status display III:
This state displays the event and action of the Smart Logic Control. For
further information, see section
Smart Logic Control .
1
30
B
P063.10
Bottom section
always shows the state of the frequency converter in Status mode.
130BP074.10
Top section
Middle section
Bottom section
Display Contrast Adjustment
Press [status] and [▲] for darker display
Press [status] and [▼] for brighter display
Indicator lights (LEDs):
If certain threshold values are exceeded, the alarm and/or warning LED lights up. A status and alarm text appear on the control panel.
The On LED is activated when the frequency converter receives power from mains voltage, a DC bus terminal, or an external 24 V supply. At the same
time, the back light is on.
• Green LED/On: Control section is working.
• Yellow LED/Warn.: Indicates a warning.
• Flashing Red LED/Alarm: Indicates an alarm.
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 5
1

GLCP keys
Menu keys
The menu keys are divided into functions. The keys below the display and
indicator lamps are used for parameter set-up, including choice of display
indication during normal operation.
130BP045.10
[Status]
Indicates the status of the frequency converter and/or the motor. 3 different readouts can be chosen by pressing the [Status] key:
5 line readouts, 4 line readouts or Smart Logic Control.
Use [Status] for selecting the mode of display or for changing back to Display mode from either the Quick Menu mode, the Main Menu mode or Alarm
mode. Also use the [Status] key to toggle single or double read-out mode.
[Quick Menu]
Allows quick set-up of the frequency converter. The most common functions can be programmed here.
The [Quick Menu] consists of:
- Q1: My Personal Menu
-Q2:QuickSetup
- Q3: Function Setups
- Q5: Changes Made
- Q6: Loggings
The Function set-up provides quick and easy access to all parameters required for the majority of water and wastewater applications including variable
torque, constant torque, pumps, dossing pumps, well pumps, booster pumps, mixer pumps, aeration blowers and other pump and fan applications.
Amongst other features it also includes parameters for selecting which variables to display on the LCP, digital preset speeds, scaling of analog references,
closed loop single zone and multi-zone applications and specific functions related to water and wastewater applications.
The Quick Menu parameters can be accessed immediately unless a password has been created via par. 0-60, 0-61, 0-65 or 0-66.
It is possible to switch directly between Quick Menu mode and Main Menu mode.
[Main Menu]
is used for programming all parameters.
The Main Menu parameters can be accessed immediately unless a password has been created via par. 0-60, 0-61, 0-65 or 0-66. For the majority of water
and wastewater applications it is not necessary to access the Main Menu parameters but instead the Quick Menu, Quick Setup and Function Setups
provides the simplest and quickest access to the typical required parameters.
It is possible to switch directly between Main Menu mode and Quick Menu mode.
Parameter shortcut can be carried out by pressing down the [Main Menu] key for 3 seconds. The parameter shortcut allows direct access to any
parameter.
[Alarm Log]
displays an Alarm list of the five latest alarms (numbered A1-A5). To obtain additional details about an alarm, use the arrow keys to manoeuvre to the
alarm number and press [OK]. Information is displayed about the condition of the frequency converter before it enters the alarm mode.
[Back]
reverts to the previous step or layer in the navigation structure.
[Cancel]
last change or command will be cancelled as long as the display has not
been changed.
[Info]
displays information about a command, parameter, or function in any
display window. [Info] provides detailed information when needed.
Exit Info mode by pressing either [Info], [Back], or [Cancel].
1 How to Programme VLT
®
AQUA Drive Programming Guide
6 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

Navigation Keys
The four navigation arrows are used to navigate between the different
choices available in [Quick Menu], [Main Menu] and [Alarm Log].
Use the keys to move the cursor.
[OK]
is used for choosing a parameter marked by the cursor and for enabling
the change of a parameter.
Operation Keys
for local control are found at the bottom of the control panel.
130BP046.10
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 7
1

[Hand On]
enables control of the frequency converter via the GLCP. [Hand on] also starts the motor, and it is now possible to give the motor speed reference by
means of the arrow keys. The key can be
Enabled [1] or Disabled [0] via par. 0-40 [Hand on] Key on LCP.
The following control signals will still be active when [Hand on] is activated:
• [Hand on] - [Off] - [Auto on]
• Reset
• Coasting stop inverse (motor coasting to stop)
• Reversing
• Set-up select lsb - Set-up select msb
• Stop command from serial communication
•Quickstop
•DCbrake
NB!
External stop signals activated by means of control signals or a serial bus will override a “start” command via the LCP.
[Off]
stops the connected motor. The key can be
Enabled [1] or Disabled [0] via par. 0-41 [Off] key on LCP. If no external stop function is selected and the
[Off] key is inactive the motor can only be stopped by disconnecting the mains supply.
[Auto On]
enables the frequency converter to be controlled via the control terminals and/or serial communication. When a start signal is applied on the control
terminals and/or the bus, the frequency converter will start. The key can be
Enabled [1] or Disabled [0] via par. 0-42 [Auto on] key on LCP.
NB!
An active HAND-OFF-AUTO signal via the digital inputs has higher priority than the control keys [Hand on] – [Auto on].
[Reset]
is used for resetting the frequency converter after an alarm (trip). The key can be
Enabled [1] or Disabled [0] via par. 0-43 Reset Keys on LCP .
The parameter shortcut
can be carried out by holding down the [Main Menu] key for 3 seconds. The parameter shortcut allows direct access to any parameter.
1.1.2 Quick Transfer of Parameter Settings between Multiple Frequency Converters
Once the set-up of a frequency converter is complete, we recommend
that you store the data in the LCP or on a PC via MCT 10 Set-up Software
Tool.
1 How to Programme VLT
®
AQUA Drive Programming Guide
8 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

Data storage in LCP:
1. Go to par.0-50
LCP Copy
2. Press the [OK] key
3. Select “All to LCP”
4. Press the [OK] key
All parameter settings are now stored in the LCP indicated by the progress bar. When 100% is reached, press [OK].
NB!
Stop the motor before performing this operation.
You can now connect the LCP to another frequency converter and copy the parameter settings to this frequency converter as well.
Data transfer from LCP to frequency converter:
1. Go to par.0-50
LCP Copy
2. Press the [OK] key
3. Select “All from LCP”
4. Press the [OK] key
The parameter settings stored in the LCP are now transferred to the frequency converter indicated by the progress bar. When 100% is reached, press
[OK].
NB!
Stop the motor before performing this operation.
1.1.3 Display Mode
In normal operation, up to 5 different operating variables can be indicated continuously in the middle section: 1.1, 1.2, and 1.3 as well as 2 and 3.
1.1.4 Display Mode - Selection of Displayed Variables
It is possible to toggle between three status read-out screens by pressing the [Status] key.
Operating variables with different formatting are shown in each status screen - see below.
Several measurements can be linked to each of the operating variables. Define the links via par. 0-20, 0-21, 0-22, 0-23, and 0-24.
Each readout parameter selected in par. 0-20 to par. 0-24 has its own scale and digits after a possible decimal point. By larger numeric value of a parameter
fewer digits are displayed after the decimal point.
Ex.: Current readout below: 5.25 A; 15.2 A 105 A.
Status screen I
This read-out state is standard after start-up or initialization.
Use [INFO] to obtain information about the measurement links to the
displayed operating variables /1.1, 1.2, 1.3, 2, and 3).
See the operating variables shown in the screen in this illustration. 1.1,
1.2 and 1.3 are shown in small size. 2 and 3 are shown in medium size.
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 9
1

130BP041.10
1.1
1.3
2
1.2
3
Status screen II:
See the operating variables (1.1, 1.2, 1.3, and 2) shown in the screen in
this illustration.
In the example, Speed, Motor current, Motor power and Frequency are
selected as variables in the first and second.
1.1, 1.2 and 1.3 are shown in small size. 2 is shown in large size.
In both status screen I and II it is possible to select other operating var-
iables by pressing
▲
or
▼
.
130BP062.10
2
1.2
1.3
1.1
Status screen III:
This state displays the event and action of the Smart Logic Control. For
further information, see section
Smart Logic Control .
1
30BP063.10
1 How to Programme VLT
®
AQUA Drive Programming Guide
10 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

1.1.5 How to operate numeric LCP (NLCP)
The following instructions are valid for the NLCP (LCP 101).
The control panel is divided into four functional groups:
1. Numeric display.
2. Menu key and indicator lights (LEDs) - changing parameters and
switching between display functions.
3. Navigation keys and indicator lights (LEDs).
4. Operation keys and indicator lights (LEDs).
NB!
Parameter copy is not possible with Numeric Local
Control Panel (LCP101).
Select one of the following modes:
Status Mode: Displays the status of the frequency converter or the mo-
tor.
If an alarm occurs, the NLCP automatically switches to status mode.
A number of alarms can be displayed.
Quick Setup or Main Menu Mode: Display parameters and parameter
settings.
Illustration 1.1: Numerical LCP (NLCP)
130BP077.10
Illustration 1.2: Status display example
130BP078.10
Illustration 1.3: Alarm display example
Indicator lights (LEDs):
• Green LED/On: Indicates if control section is on.
• Yellow LED/Wrn.: Indicates a warning.
• Flashing red LED/Alarm: Indicates an alarm.
Menu key
[Menu] Select one of the following modes:
• Status
•QuickSetup
• Main Menu
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 11
1

Main Menu
is used for programming all parameters.
The parameters can be accessed immediately unless a password has been created via par.0-60
Main Menu Password , par.0-61 Access to Main Menu w/
o Password
, par.0-65 Personal Menu Password or par.0-66 Access to Personal Menu w/o Password .
Quick Setup is used to set up the frequency converter using only the most essential parameters.
The parameter values can be changed using the up/down arrows when the value is flashing.
Select Main Menu by pressing the [Menu] key a number of times until the Main Menu LED is lit.
Select the parameter group [xx-__] and press [OK]
Select the parameter [__-xx] and press [OK]
If the parameter is an array parameter select the array number and press [OK]
Select the wanted data value and press [OK]
Navigation Keys
[Back]
for stepping backwards
Arrow [
▲
] [
▼
]
keys are used for manoeuvring between parameter groups, parameters
and within parameters
[OK]
is used for choosing a parameter marked by the cursor and for enabling
the change of a parameter.
130BP079.10
Illustration 1.4: Display example
Operation Keys
Keys for local control are found at the bottom of the control panel.
130BP046.10
Illustration 1.5: Operation keys of the numerical LCP (NLCP)
[Hand on]
enables control of the frequency converter via the LCP. [Hand on] also starts the motor and it is now possible to enter the motor speed data by means
of the arrow keys. The key can be
Enabled [1] or Disabled [0] via par.0-40 [Hand on] Key on LCP .
External stop signals activated by means of control signals or a serial bus will override a 'start' command via the LCP.
The following control signals will still be active when [Hand on] is activated:
• [Hand on] - [Off] - [Auto on]
• Reset
• Coasting stop inverse
• Reversing
• Set-up select lsb - Set-up select msb
• Stop command from serial communication
•Quickstop
•DCbrake
[Off]
stops the connected motor. The key can be
Enabled [1] or Disabled [0] via par.0-41 [Off] Key on LCP .
If no external stop function is selected and the [Off] key is inactive the motor can be stopped by disconnecting the mains supply.
[Auto on]
enables the frequency converter to be controlled via the control terminals and/or serial communication. When a start signal is applied on the control
terminals and/or the bus, the frequency converter will start. The key can be
Enabled [1] or Disabled [0] via par.0-42 [Auto on] Key on LCP .
1 How to Programme VLT
®
AQUA Drive Programming Guide
12 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

NB!
An active HAND-OFF-AUTO signal via the digital inputs has higher priority than the control keys [Hand on] [Auto on].
[Reset]
is used for resetting the frequency converter after an alarm (trip). The key can be
Enabled [1] or Disabled [0] via par.0-43 [Reset] Key on LCP .
1.1.6 Parameter Set-Up
The frequency converter can be used for practically all assignments, thus offering a significant number of parameters. The series offers a choice between
two programming modes - a Quick Menu mode and a Main Menu mode.
The latter provides access to all parameters. The former takes the user through a few parameters making it possible to program the majority of
water/ wastewater applications.
Regardless of the mode of programming, you can change a parameter both in the Quick Menu mode and in the Main Menu mode.
1.1.7 Quick Menu Mode
The GLCP provides access to all parameters listed under the Quick Menus. To set parameters using the [Quick Menu] button:
Pressing [Quick Menu] the list indicates the different areas contained in the Quick menu.
Efficient Parameter Set-up for Water Applications
The parameters can easily be set up for the vast majority of the water and wastewater applications only by using the [Quick Menu].
The optimum way to set parameters through the [Quick Menu] is by following the below steps:
1. Press [Quick Setup] for selecting basic motor settings, ramp times, etc.
2. Press [Function Setups] for setting up the required functionality of the frequency converter - if not already covered by the settings in [Quick
Setup].
3. Choose between
General Settings , Open Loop Settings and Closed Loop Settings.
It is recommended to do the set-up in the order listed.
Illustration 1.6: Quick menu view.
Par. Designation [Units]
0-01 Language
1-20 Motor Power [kW]
1-22 Motor Voltage [V]
1-23 Motor Frequency [Hz]
1-24 Motor Current [A]
1-25 Motor Nominal Speed [RPM]
3-41 Ramp 1 Ramp up Time [s]
3-42 Ramp 1 Ramp down Time [s]
4-11 Motor Speed Low Limit [RPM]
4-13 Motor Speed High Limit [RPM]
1-29 Automatic Motor Adaptation (AMA)
Table 1.1: Quick Setup parameters
If
No Operation is selected in terminal 27 no connection to +24 V on terminal 27 is necessary to enable start.
If
Coast Inverse (factory default value) is selected in Terminal 27, a connection to +24V is necessary to enable start.
NB!
For detailed parameter descriptions, please see the following section on
Commonly Used Parameters - Explanations .
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 13
1

1.1.8 Q3 Function Setups
The Function Setup provides quick and easy access to all parameters required for the majority of water and wastewater applications including variable
torque, constant torque, pumps, dossing pumps, well pumps, booster pumps, mixer pumps, aeration blowers and other pump and fan applications.
Amongst other features it also includes parameters for selecting which variables to display on the LCP, digital preset speeds, scaling of analog references,
closed loop single zone and multi-zone applications and specific functions related to water and wastewater applications.
How to access Function Set-up - example:
130BT110.1
0
Illustration 1.7: Step 1: Turn on the frequency converter (On
LED lights)
130BT111.1
0
Illustration 1.8: Step 2: Press the [Quick Menus] button
(Quick Menus choices appear).
130BT112.1
0
Illustration 1.9: Step 3: Use the up/down navigation keys to
scroll down to Function Setups. Press [OK].
130BA500.1
0
Illustration 1.10: Step 4: Function Setups choices appear.
Choose 03-1
General Settings . Press [OK].
130BA501.1
0
Illustration 1.11: Step 5: Use the up/down navigation keys
to scroll down to i.e. 03-12
Analog Outputs . Press [OK].
130BA502.1
0
Illustration 1.12: Step 6: Choose parameter 6-50 Terminal
42 Output
. Press [OK].
130BA503.1
0
Illustration 1.13: Step 7: Use the up/down navigation keys
to select between the different choices. Press [OK].
1 How to Programme VLT
®
AQUA Drive Programming Guide
14 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

The Function Setup parameters are grouped in the following way:
Q3-1 General Settings
Q3-10 Clock Settings Q3-11 Display Settings Q3-12 Analog Output Q3-13 Relays
0-70 Set Date and Time 0-20 Display Line 1.1 Small 6-50 Terminal 42 Output Relay 1 ⇒5-40 Function Relay
0-71 Date Format 0-21 Display Line 1.2 Small 6-51 Terminal 42 Output Min Scale Relay 2 ⇒5-40 Function Relay
0-72 Time Format 0-22 Display Line 1.3 Small 6-52 Terminal 42 Output Max Scale Option relay 7 ⇒5-40 Function
Relay
0-74 DST/Summertime 0-23 Display Line 2 Large Option relay 8 ⇒5-40 Function
Relay
0-76 DST/Summertime Start 0-24 Display Line 3 Large Option relay 9 ⇒5-40 Function
Relay
0-77 DST/Summertime End 0-37 Display Text 1
0-38 Display Text 2
0-39 Display Text 3
Q3-2 Open Loop Settings
Q3-20 Digital Reference Q3-21 Analog Reference
3-02 Minimum Reference 3-02 Minimum Reference
3-03 Maximum Reference 3-03 Maximum Reference
3-10 Preset Reference 6-10 Terminal 53 Low Voltage
5-13 Terminal 29 Digital Input 6-11 Terminal 53 High Voltage
5-14 Terminal 32 Digital Input 6-14 Terminal 53 Low Ref/Feedb. Value
5-15 Terminal 33 Digital Input 6-15 Terminal 53 High Ref/Feedb. Value
Q3-3 Closed Loop Settings
Q3-30 Feedback Settings Q3-31 PID Settings
1-00 Configuration Mode 20-81 PID Normal/Inverse Control
20-12 Reference/Feedb.Unit 20-82 PID Start Speed [RPM]
3-02 Minimum Reference 20-21 Setpoint 1
3-03 Maximum Reference 20-93 PID Proportional Gain
6-20 Terminal 54 Low Voltage 20-94 PID Integral Time
6-21 Terminal 54 High Voltage
6-24 Terminal 54 Low Ref/Feedb Value
6-25 Terminal 54 High Ref/Feedb Value
6-00 Live Zero Timeout Time
6-01 Live Zero Timeout Function
1.1.9 Main Menu Mode
Both the GLCP and NLCP provide access to the main menu mode. Select
the Main Menu mode by pressing the [Main Menu] key. Illustration 6.2
shows the resulting read-out, which appears on the display of the GLCP.
Lines 2 through 5 on the display show a list of parameter groups which
can be chosen by toggling the up and down buttons.
1
30BP066.10
Illustration 1.14: Display example.
Each parameter has a name and number which remain the same regardless of the programming mode. In the Main Menu mode, the parameters are
divided into groups. The first digit of the parameter number (from the left) indicates the parameter group number.
All parameters can be changed in the Main Menu. The configuration of the unit (par.1-00
Configuration Mode ) will determine other parameters available
for programming. For example, selecting Closed Loop enables additional parameters related to closed loop operation. Option cards added to the unit
enable additional parameters associated with the option device.
1.1.10 Parameter Selection
In the Main Menu mode, the parameters are divided into groups. Select
a parameter group by means of the navigation keys.
The following parameter groups are accessible:
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 15
1

Group no. Parameter group:
0Operation/Display
1Load/Motor
2Brakes
3 References/Ramps
4Limits/Warnings
5DigitalIn/Out
6Analog In/Out
8 Comm. and Options
9Profibus
10 CAN Fieldbus
11 LonWorks
13 Smart Logic
14 Special Functions
15 Drive Information
16 Data Readouts
18 Data Readouts 2
20 Drive Closed Loop
21 Ext. Closed Loop
22 Application Functions
23 Time-based Functions
24 Fire Mode
25 Cascade Controller
26 Analog I/O Option MCB 109
Table 1.2: Parameter groups.
After selecting a parameter group, choose a parameter by means of the
navigation keys.
The middle section on the GLCP display shows the parameter number and
name as well as the selected parameter value.
1
30BP067.10
Illustration 1.15: Display example.
1.1.11 Changing Data
The procedure for changing data is the same whether you select a parameter in the Quick menu or the Main menu mode. Press [OK] to change the
selected parameter.
The procedure for changing data depends on whether the selected parameter represents a numerical data value or a text value.
1.1.12 Changing a Text Value
If the selected parameter is a text value, change the text value by means
of the up/down navigation keys.
The up key increases the value, and the down key decreases the value.
Place the cursor on the value to be saved and press [OK].
130BP068.10
Illustration 1.16: Display example.
1 How to Programme VLT
®
AQUA Drive Programming Guide
16 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

1.1.13 Changing a Group of Numeric Data Values
If the chosen parameter represents a numeric data value, change the
chosen data value by means of the [◄] and [►] navigation keys as well
as the up/down [
▲
] [
▼
] navigation keys. Use the ◄] and [►] navigation
keys to move the cursor horizontally.
130BP069.10
Illustration 1.17: Display example.
Use the up/down navigation keys to change the data value. The up key
enlarges the data value, and the down key reduces the data value. Place
the cursor on the value to be saved and press [OK].
130BP070.10
Illustration 1.18: Display example.
1.1.14 Changing of Data Value, Step-by-Step
Certain parameters can be changed step by step or infinitely variably. This applies to par.1-20 Motor Power [kW] , par. 1-22 Motor Voltage and par.
1-23
Motor Frequency .
The parameters are changed both as a group of numeric data values and as numeric data values infinitely variably.
1.1.15 Read-out and Programming of Indexed Parameters
Parameters are indexed when placed in a rolling stack.
par.15-30
Alarm Log: Error Code to par.15-32 Alarm Log: Time contain a fault log which can be read out. Choose a parameter, press [OK], and use the
up/down navigation keys to scroll through the value log.
Use par.3-10
Preset Reference as another example:
Choose the parameter, press [OK], and use the up/down navigation keys keys to scroll through the indexed values. To change the parameter value,
select the indexed value and press [OK]. Change the value by using the up/down keys. Press [OK] to accept the new setting. Press [Cancel] to abort.
Press [Back] to leave the parameter.
1.1.16 Initialisation to Default Settings
Initialise the frequency converter to default settings in two ways:
Recommended initialisation (via par.14-22
Operation Mode )
1. Select par.14-22
Operation Mode
2. Press [OK]
3. Select “Initialisation”
4. Press [OK]
5. Cut off the mains supply and wait until the display turns off.
6. Reconnect the mains supply - the frequency converter is now
reset.
7. Change par.14-22
Operation Mode back to Normal Operation .
VLT
®
AQUA Drive Programming Guide 1 How to Programme
MG.20.O4.02 - VLT®is a registered Danfoss trademark 17
1

NB!
Resets parameters selected in Personal Menu with default factory setting.
par.14-22 Operation Mode initialises all except:
par. 14-50 RFI Filter
par. 8-30 Protocol
par.8-31 Address
par.8-32 Baud Rate
par.8-35 Minimum Response Delay
par.8-36 Maximum Response Delay
par.8-37 Maximum Inter-Char Delay
par.15-00 Operating Hours to par.15-05 Over Volt's
par.15-20 Historic Log: Event to par.15-22 Historic Log: Time
par.15-30 Alarm Log: Error Code to par.15-32 Alarm Log: Time
Manual initialisation
1. Disconnect from mains and wait until the display turns off.
2a. Press [Status] - [Main Menu] - [OK] at the same time while power up for LCP 102, Graphical Display
2b. Press [Menu] while power up for LCP 101, Numerical Display
3. Release the keys after 5 s.
4. The frequency converter is now programmed according to default settings.
This procedure initializes all except: par.15-00 Operating Hours ; par.15-03 Power Up's ; par.15-04 Over Temp's ; par.15-05 Over Volt's .
NB!
When you carry out manual initialisation, you also reset serial communication, par. 14-50
RFI Filter and fault log settings.
Removes parameters selected in par.25-00
Cascade Controller .
NB!
After initialization and power cycling, the display will not show any information until after a couple of minutes.
1 How to Programme VLT
®
AQUA Drive Programming Guide
18 MG.20.O4.02 - VLT®is a registered Danfoss trademark
1

2 Parameter Description
2.1.1 Parameter Set-Up
Overview of parameter groups
Group Title Function
0- Operation / Display Parameters related to the fundamental functions of the frequency converter, function of
the LCP buttons and configuration of the LCP display.
1- Load / Motor Parameter group for motor settings.
2- Brakes Parameter group for setting brake features in the frequency converter.
3- Reference / Ramps Parameters for reference handling, definitions of limitations, and configuration of the re-
action of the frequency converter to changes.
4- Limits / Warnings Parameter group for configuring limits and warnings.
5- Digital In/Out Parameter group for configuring the digital inputs and outputs.
6- Analog In/Out Parameter group for configuration of the analog inputs and outputs.
8- Communication and Options Parameter group for configuring communications and options.
9- Profibus Parameter group for Profibus-specific parameters.
10- DeviceNet Fieldbus Parameter group for DeviceNet-specific parameters.
13- Smart Logic Parameter group for Smart Logic Control
14- Special Functions Parameter group for configuring special frequency converter functions.
15- Drive Information Parameter group containing frequency converter information such as operating data,
hardware configuration and software versions.
16- Data Readouts Parameter group for data read-outs, e.g. actual references, voltages, control, alarm,
warning and status words.
18- Info and Readouts This parameter group contains the last 10 Preventive Maintenance logs.
20- Drive Closed Loop This parameter group is used for configuring the closed loop PID Controller that controls
the output frequency of the unit.
21- Extended Closed Loop Parameters for configuring the three Extended Closed Loop PID Controllers.
22- Application Functions These parameters monitor water applications.
23- Time-based Functions These parameters are for actions needed to be performed on a daily or weekly basis, e.g.
different references for working hours/non-working hours.
25- Basic Cascade Controller Functions Parameters for configuring the Basic Cascade Controller for sequence control of multiple
pumps.
26- Analog I/0 Option MCB 109 Parameters for configuring the Analog I/0 Option MCB 109.
27- Extended Cascade Control Parameters for configuring the Extended Cascade Control.
29- Water Application Functions Parameters for setting water specific functions.
31- Bypass Option Parameters for configuring the Bypass Option
Table 2.1: Parameter Groups
Parameter descriptions and selections are displayed on the graphic (GLCP) or numeric (NLCP) in the display area. (See Section 5 for details.) Access the
parameters by pressing the [Quick Menu] or [Main Menu] key on the control panel. The quick menu is used primarily for commissioning the unit at start-
up by providing those parameters necessary to start operation. The main menu provides access to all parameters for detailed application programming.
All digital input/output and analog input/output terminals are multifunctional. All terminals have factory default functions suitable for the majority of water
applications but if other special functions are required, they must be programmed in parameter group 5 or 6.
2.2 Main Menu - Operation and Display - Group 0
2.2.1 0-** Operation / Display
Parameters related to the fundamental functions of the frequency converter, function of the LCP buttons and configuration of the LCP display.
2.2.2 0-0* Basic Settings
Parameter group for basic frequency converter settings.
VLT
®
AQUA Drive Programming Guide 2 Parameter Description
MG.20.O4.02 - VLT®is a registered Danfoss trademark 19
2

0-01 Language
Option: Function:
Defines the language to be used in the display.
The frequency converter can be delivered with 2 different language packages. English and German
are included in both packages. English cannot be erased or manipulated.
[0] * English Part of Language packages 1 - 2
[1] Deutsch Part of Language packages 1 - 2
[2] Francais Part of Language package 1
[3] Dansk Part of Language package 1
[4] Spanish Part of Language package 1
[5] Italiano Part of Language package 1
[6] Svenska Part of Language package 1
[7] Nederlands Part of Language package 1
[10] Chinese Language package 2
[20] Suomi Part of Language package 1
[22] English US Part of Language package 1
[27] Greek Part of Language package 1
[28] Bras.port Part of Language package 1
[36] Slovenian Part of Language package 1
[39] Korean Part of Language package 2
[40] Japanese Part of Language package 2
[41] Turkish Part of Language package 1
[42] Trad.Chinese Part of Language package 2
[43] Bulgarian Part of Language package 1
[44] Srpski Part of Language package 1
[45] Romanian Part of Language package 1
[46] Magyar Part of Language package 1
[47] Czech Part of Language package 1
[48] Polski Part of Language package 1
[49] Russian Part of Language package 1
[50] Thai Part of Language package 2
[51] Bahasa Indonesia Part of Language package 2
2 Parameter Description VLT
®
AQUA Drive Programming Guide
20 MG.20.O4.02 - VLT®is a registered Danfoss trademark
2