Danfoss DEVIreg 132 User manual

www.DEVI.com
Installation Guide
DEVIreg™ 132
Electronic Thermostat

DEVIreg™ 132
Installation Guide2

DEVIreg™ 132
Installation Guide 3
1 Introduction
DEVIreg™ 132 is an electronic thermostat to be installed
directly on the wall. It is provided with a room sensor to
control the room temperature and an additional oor
sensor to limit the maximum oor temperature.
The thermostat has a button for adjusting the temperature,
with a scale from ( ) 5-45 °C, and an LED indicator showing
standby (green light) and heating periods (red light).
More information on this product can also be found at:
devireg.devi.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . 6
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Disposal Instruction . . . . . . . . . . . . . . . . . . 14

DEVIreg™ 132
Installation Guide4
1.1 Technical Specications
Operation voltage 220-240 V~, 50 Hz
Standby power consumption Max 5W
Relay:
Resistive load
Inductive load
Max 16 A / 3680 W @ 230 V
cos φ= 0.3 max 1 A
Sensing units NTC 15 kOhm at 25 °C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0,2 °C
Ambient temperature 0 to +30 °C
Frost protection temperature 5 °C -
Temperature range
5-35 °C room temperature
20-50 °C oor temperature
limiter - default 35 °C
Cable specication max 1 x 4 mm² or 2 x 2,5 mm²
Ball pressure temperature 75 °C
Pollution degree Degree 2 (domestic use)
Type 1C
Storage temperature -20 to +65 °C
IP class 30
Protection class Class II -

DEVIreg™ 132
Installation Guide 5
Dimensions 82 x 82 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned o
before installation.
IMPORTANT: When the thermostat is used to control a
oor heating element in connection with a wooden oor or
similar material, always use a oor sensor and never set the
maximum oor temperature to more than 35°C.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualied installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.

DEVIreg™ 132
Installation Guide6
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
Place the thermostat at a suitable height on
the wall (typically 80-170 cm.).
In wet rooms, place the thermostat according
to local regulation on IP classes.
Do not place the thermostat on the inner side
of an exterior wall.
Always install the thermostat at least 50 cm
from windows and doors.
Do not place the thermostat in a way that it
will be exposed to direct sunlight.

DEVIreg™ 132
Installation Guide 7
Note: A oor sensor enables a more accurate
temperature control and is recommended in
all oor heating applications and mandatory
under wooden oors to reduce the risk of
over-heating the oor.
• Place the oor sensor in a conduit in an appropriate
place where it is not exposed to sunlight or draft from
door openings.
• Equally distant and >2cm from two heating cables.
• The conduit should be ush with the oor surface -
countersink the conduit if necessary.
• Route the conduit to the connection box.
• The bending radius of the conduit must be min
50mm.

DEVIreg™ 132
Installation Guide8
Follow the steps below to mount the thermostat:
1. Open the thermostat:
• Remove the button to get access to the screw which
holds the front.
• Loosen the screw.
• Push down the release tab at the top of the thermo-
stat using a at object while slowly pulling o the
front cover.

DEVIreg™ 132
Installation Guide 9
2. Fasten the thermostat directly to the wall by driving
the screws through the holes in each side of the
thermostat.
= Screw holes for fastening the thermostat.
3. Connect the thermostat according to the connection
diagram.
IP30
0T30
D132
NTC
1234
Sensor
Max.Load
16 (1) A
Mains
220-240V~
N
LOAD
L
LOAD
NL
The screen of the heating cable must be connected
via a connector together with the earth conductor of
the power supply cable.
Note: Always install the oor sensor in a conduit in
the oor.

DEVIreg™ 132
Installation Guide10
4. Set the maximum oor temperature between 20 °C
and 50 °C by using a thin screwdriver on the black
electronic component with temperature indications in
the upper right corner.
5. Install the front cover and button in the reverse order
of disassembly.
6. Turn on the power supply.
3 Settings
How to change the minimum and maximum oor
temperatures
1. Lift o the adjustment
button using a thin
screwdriver. 
2. Move the pins to the de-
sired positions.
(and )
3. Put the adjustment button
back in place.
Please be aware of the following:
• The oor temperature is measured where the sensor
is placed.
• The temperature of the bottom of a wooden oor can
be up to 10 degrees higher than the top.