Danfoss TP9000 User manual

TP9000
Electronic Programmable Room Thermostat
plus Domestic Hot Water Timer
Installation Guide
Danfoss Heating
MAKING MODERN LIVING POSSIBLE

TP9000
2
For a large print version of these instructions
please call Marketing on 0845 121 7400.
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other
printed material. All trademarks in this material are property of the respective companies.
Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

Danfoss Heating 3
GB
PL
GR
ES
GB
TP9000
Electronic Programmable Room Thermostat
plus Domestic Hot Water Timer
1.0 Basics
1.0 Product specification...................................................................4
1.1 Installation.......................................................................................5
1.2 Wiring ................................................................................................7
2.0 Installer advanced programming options
2.1 Installer advanced programming options...........................9
2.2 Service Interval Timer..................................................................9
2.3 Entering Installer Advanced Programming Mode ............9
Installation Instructions

TP9000
4
GB
PL
GR
ES
GB
Please note: This product should only be installed by a
qualified electrician or competent Heating installer, and should
be in accordance with the current edition of the IEEE wiring
regulations.
Specification 230V model 24V model
Power supply 230 Vac, ±15%,
50/60 Hz
24 Vac, ±15%,
50/60 Hz
Switching action
2 x SPDT internally linked, Type 1BS
Unit switch rating 230 Vac, 3(1)A 24Vac, 3(1)A
Memory Backup Retained for life of product
Heat Temperature Range
Setting
5°C - 30°C
Factory Set Calendar
Clock
Automatic Summer/Winter time
change
Remote Sensor Inputs
(‘A’models only)
Can be set by installer for remote sen-
sor, limited sensor, window contact,
tele-switch or outdoor sensor
Programme resolution ± 1 minute
Timing Accuracy ± 1 minute
Dimensions, mm (W, H, D) 135 x 88 x 32mm
Design standard EN 60730-2-7 +EN60730-2-9
Control Pollution Situ-
ation
Degree 2
Rated Impulse Voltage 2.5 kV
Ball Pressure Test 75°C
1.0 Product specification
1.0 Basics

Danfoss Heating 5
GB
PL
GR
ES
GB
1.1 Installation
• Remove wallplate from unit by unscrewing the two screws on
the bottom edge of the unit.
• From the top left hand corner of the wallplate, there must be
clearances of at least 140 mm to the right, 15mm to the left,
30mm above and 100mm below in order to mount the plug-on
module.
• The wallplate must be securely mounted either directly to the
wall using suitable wood screws or to a flush mounted 1-gang
electrical accessory box using M3.5 screws.
• Cable access can either be from behind for concealed cabling, or
from below for surface cabling. If surface cable is used, cut out
cable access slot on plug-on module prior to mounting.
• For wiring connections refer to diagram on page 7.
The TP9000 is double insulated and does not require an earth
connection, however a parking terminal is provided on the
wallplate. This is clearly marked with an Earth symbol.
• Prior to mounting the plug-on module, DIL switches on the
rear of the plug-on module must be set. See diagram below for
available options.
• Mount plug-on module to wallplate by locating tabs on top of
wallplate in apertures on rear of module, hinge down and press
firmly to wallplate before tightening securing screws on bottom
of wallplate.
1
2
Keyboard disabled
Reset disabled Reset enabled
Keyboard enabled
OFF ON
Sw. No.
Prior to mounting the unit the 2 DIL switches on the rear of the
unit have to be moved to the required position. The factory
presets are shown below.

TP9000
6
GB
PL
GR
ES
GB
IMPORTANT: The supply to this unit should by wired via a double
pole isolation switch in accordance with BS EN60730-1, i.e. one
which provides air gaps of at least 3mm in both poles of the mains,
and incorporates a 3 amp fuse. It is strongly recommended that solid
conductors be used.
Clearance for
screwdriver
access
Surface fixed cable
bottom entry knockouts
Rear entry
cable access
N &
looping
terminals
Wall or
Plaster box
fitting
Terminal block
Outline of unit
30mm minimum
C/L
!
Thermostat and Remote Room Sensor:
Fix at a height of approximately 1.5m from the floor, away from
draughts or heat sources such as radiators, open fires or direct
sunlight.

Danfoss Heating 7
GB
PL
GR
ES
GB
1.2 Wiring
NOTE:
The 230V TP9000 does not have voltage free contacts, therefore it is
NOT suitable for connection to extra low voltage equipment.
Remote Sensor to be wired with 1mm 2 core double insulated cable
only. Cable length should not exceed 50 metres. Sensor cable should
NOT be run parallel to mains cable.
NBLC
Remote sensor inputs
The TP9000 incorporates an input which can be used to connect one
of the following:
1) remote room temperature sensor
2) limit sensor, for example, floor temperature sensor (sold as
accessory).
3) window contacts, card reader contacts, outdoor sensor (sold as
accessory) or teleswitch contacts.
See Installer Advanced Programming Options for set-up
instructions.
N-L = 230V
B-C = 24V
(B=0v / C=24v)

TP9000
8
GB
PL
GR
ES
GB
Remote sensor inputs
Terminals 5 and 6 are the designated remote sensor inputs.These can
be found on the top right hand side of the wallplate.
56
Window or
teleswitch
contact
(NO or NC)
56
Teleswitch
contact (NC)
Window
contact (NC)
56
Configured for
remote room,
limit or outdoor
sensor
Configured for
window contact or
other contact such
as teleswitch
Configured for
window contact
and other contact
such as teleswitch

Danfoss Heating 9
GB
PL
GR
ES
GB
2.0 Installer advanced
programming options
TP9000 incorporates a number of advanced features which can be set
by the user. These are accessed via a User Advanced Programming
Mode, please refer to User Advanced Programming in the user
instructions for details (see page 23)
2.1 Installer advanced programming options
TP9000 incorporates an additional number of advanced features
which can be set by the installer to improve the operating efficiency
of the system and where required, to change the user functionality
of the product. These are accessed via an Installer Advanced
Programming Mode. These settings are optional and need only be
made if there is a demand for the enhanced functions.
2.2 Service Interval Timer
Instructions on how to access this feature are available from our
customer support desk. Please note these are only issued to boni-fide
Heating installers.
2.3 Entering Installer Advanced Programming
Mode
To access the Installer Advanced Programming Mode follow the
steps below:
a) Press and hold Vand PROG for 3 seconds
to enter User Advanced Programming, the
display will change to figure opposite.
b) Press and hold V, Λand PROG for 5 seconds
to enter Installer Advanced Programming, the
display will change to figure opposite.

TP9000
10
GB
PL
GR
ES
GB
c) Use +and -keys to scroll backwards and forwards between
options then Vand Λkeys to change the option settings. The
flashing digit on the right hand of the display indicates the
number of the selected option. The large characters display the
option value selected.
d) To return to RUN, press and hold PROG until the display returns
to RUN mde.
Option 30 - Set upper limit of temperature range
This allows the upper limit of the thermostat
setting range to be electronically limited. Press +
until Option 30 is displayed, use Vand Λto select
required setting.
Setting 40 - 5°C (factory setting is 30°C)
Option 31 - Set lower limit of temperature range
This allows the lower limit of the thermostat
setting range to be electronically limited. Press +
until Option 31 is displayed, use Vand Λto select
required setting.
Setting 5 - 40°C (factory setting is 5°C)
Option 32 - Enable Off at lower limit
This enables an OFF function to be selected if a
set point below the lower limit is selected. Press +
until Option 32 is displayed, use Vand Λto select
required setting.
Setting 0 Disabled
Setting 1 Enabled (factory setting)
Option 33 - Enable On at upper limit
This enables an ON function to be selected if a set
point above the upper limit is selected. Press +
until Option 33 is displayed, use Vand Λto select
required setting.
Setting 0 Disabled (factory setting)
Setting 1 Enabled