Danfoss DEVIreg 530 User manual

www.DEVI.com
Installation Guide
DEVIreg™ 530
Electronic Thermostat

DEVIreg™ 530
Installation Guide2
The English language is used for the original instructions.
Other languages are a translation of the original instructions.
(Directive 2006/42/EC)

DEVIreg™ 530
Installation Guide 3
1 Introduction
DEVIreg™ 530 is an electronic thermostat provided with a
2-pole switch and a wire sensor to measure and control the
desired oor temperature. It can be either ush-mounted
(standard) or surface-mounted (using special box).
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 1 to 6 (each step corresponds
to approximately 8°C). Furthermore, it has a LED indicator
showing standby periods (green light) and heating periods
(red light).
More information on this product can also be found at:
devireg.devi.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . 6
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Disposal Instruction . . . . . . . . . . . . . . . . . . 14

DEVIreg™ 530
Installation Guide4
1.1 Technical Specications
Operation voltage 220-240V~, 50Hz
Standby power
consumption
Max 0.25W
Relay:
Resistive load
Inductive load
Max 15A / 3450W @ 230V
cos φ= 0.3 max 1A
Sensing units NTC 15kOhm at 25°C
Sensing values:
0°C
25°C
50°C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0.4°C
Ambient temperature -10 to +30°C
Frost protection
temperature
5 °C -
Temperature range ( ) 5-45°C with oor
sensor only
Cable specication max 1x4mm² or 2x2,5mm²
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)

DEVIreg™ 530
Installation Guide 5
Type 1C
Storage temperature -20 to +65°C
IP class 31
Protection class Class II -
Dimensions 85 x 85 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard «Automatic
electrical controls for household and similar use»:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned o
before installation.
IMPORTANT: When the thermostat is used to control a
oor heating element in connection with a wooden oor or
similar material, always use a oor sensor and never set the
maximum oor temperature to more than 35°C.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualied installer according to local
regulations.

DEVIreg™ 530
Installation Guide6
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Place the thermostat at a suitable height
on the wall (typically 80-170cm.).
In wet rooms, place the thermostat according
to local regulation on IP classes.

DEVIreg™ 530
Installation Guide 7
Note: A oor sensor enables a more accurate
temperature control and is recommended
in all oor heating applications
and mandatory under wooden oors to
reduce the risk of over-heating the oor.
• Place the oor sensor in a conduit in an appropriate
place where it is not exposed to sunlight or draft from
door openings.
• Equally distant and >2cm from two heating cables.
• The conduit should be ush with the oor surface -
countersink the conduit if necessary.
• Route the conduit to the connection box.
• The bending radius of the conduit must be min 50mm.

DEVIreg™ 530
Installation Guide8
Follow the steps below to mount the thermostat:
1. Open the thermostat:
devireg™550
3
5
6
24
20
30
40
50
• Press the release tab in the bottom of the
thermostat using a at object.
• Carefully detach the front cover.
• Carefully detach the frame.

DEVIreg™ 530
Installation Guide 9
2. Connect the thermostat according to the connection
diagram.
IP31
-10T30
D530
Mains
220-240V~
Max. Load
15 (1) A
Sensor
NL NTC
N
LOAD
L
LOAD
-5°C
L
9
By connecting an external timer to the terminal
marked by a moon symbol (and by using for example
the same phase as for the mains power supply), the
thermostat can be set to reduce the temperature by
5°C during specied periods.
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: Always install the oor sensor in a conduit in
the oor.

DEVIreg™ 530
Installation Guide10
3. Mount and reassemble the thermostat.
• Fasten the thermostat to a socket or an exterior
wall box by driving the screws through the holes
in each side of the thermostat.
• Install the frame and front cover in the reverse
order of disassembly.
4. Turn on the power supply.
3 Settings
How to change the minimum and maximum oor
temperatures
1. Remove the adjustment button.
2. Move the pins to the desired
positions.
3. Put the adjustment button back
in place.
devireg™550
3
5
6
24
20
30
40
50
Note: Please be aware of the following:
• The oor temperature is measured where the oor
sensor is placed.
• The temperature of the bottom of a wooden oor can
be up to 10 degrees higher than the top.