Danfoss TP5000 RF Si User manual

TP5000 + RF
Installation Instructions
User Instructions
Instructions d’installation
Instructions d’utilisateur
Installationsanweisungen
Inbetriebnahme-Instruktion
Instrucciones de instalación
Instrucciones del usuario
Instruktions vejledning
Brugervejleding
Electronic 5/2 day programmable room thermostat
Installatie handleiding
Instructiesevoor Gebruik
Ïäçãßåò åãêáôÜóôáóçò
Ïäçãßåò ÷ñÞóçò
Instrukcja instalacji
Instrukcja Użytkownika
Montavimo instrukcijos
Informacija Vartotojui
Istruzioni per l’uso
Istruzioni per l’utente
GB
F
D
ES
DK
NL
GR
P
LT
I
®
Certification Mark

2
INDEX
Installation Instructions 3-6
User Instructions 7-13
Instructions d’installation 14-17
Instructions d’utilisateur 18-23
Installationsanweisungen 24-27
Inbetriebnahme-Instruktion 28-33
Instrucciones de instalación 34-37
Instrucciones del usuario 38-43
Instruktions vejledning 44-47
Brugervejleding 48-53
Installatie handleiding 54-57
Instructiesevoor Gebruik 58-63
Ïäçãßåò åãêáôÜóôáóçò 64-67
Ïäçãßåò ÷ñÞóçò 68-73
Instrukcja instalacji 74-77
Instrukcja Użytkownika 78-83
Montavimo instrukcijos 84-87
Informacija Vartotojui 88-93
Istruzioni per l’uso 94-97
Istruzioni per l’utente 98-103
GB
F
D
ES
DK
NL
GR
P
LT
I

3
Installation Instructions
Important note RF products: Ensure that there are no large metal objects,such as boiler cases
or other large appliances, in line of sight between the transmitter and receiver as these will
prevent communication between thermostat and receiver.
Product Specification
Please Note:
This product should only be installed by a qualified
electrician or competent heating installer and should be
in accordance with the current edition of the IEEE wiring
regulations.
Thermostat features TP5000 TP5000-RF
Power supply 2 x AA/MN1500/LR alkaline cells
Memory back-up 1 min for battery change
Switching action of output relay
1 x SPDT,Type 1B N/A
Switch rating of relay contact 3(1)A, 10-230Vac N/A
Transmission frequency (RF model) N/A 433.92MHz
Transmitter range (RF model) N/A 30m max
Temperature range 5-30°C
Dimensions, mm 110 wide, 88 high, 28 deep
Design standard EN60730-2-9 (EN300220 for RF)
Rated impulse voltage 2.5Kv
Ball hardness test 75°C
Control pollution situation Degree 2
Temperature accuracy ±1°C
Time accuracy ±1 min.
Installation Instructions
GB

4
Installation
 First, remove the wallplate from the back of the unit.
 From the top left hand corner of the wallplate, there must be
clearances of at least 140mm to the right, 15mm to the left,
30mm above and 100mm below in order to mount the plug-
in module.
 Fix at a height of approximately 1.5m from the floor, away
from draughts or heat sources such as radiators, open fires or
direct sunlight.
 Prior to mounting the unit should be set in either ON/OFF or
chrono-proportional control mode (see below).
1) ON/OFF - boiler switches ON when below set temperature
and OFF when above.
1) ON/OFF 2) CHRONO
Installation Instructions
GB

5
!
2) Chrono-Proportional - energy saving feature which fires
the boiler at regular intervals to maintain a set temperature,
achieving a constant ambient environment for the user.
Thermostat Wiring (not RF models)
Some existing thermostats will have a Neutral and/or Earth wire connected. These
are not required by the TP5000 and must NOT be connected to any TP5000 terminals.
Instead they should be made electrically safe and coiled in the recess at the back of
the TP5000.
RX1 & RX2 RX3
COM
RX Receiver Wiring (RF models only)
1) For mains voltage operated systems link terminal 2 to mains live supply.
2) Power supply to unit must not be switched by timeswitch.
Installation Instructions
GB

6
Commissioning (RF models only)
If the thermostat and the receiver have been supplied together in
a combined pack, the units have been paired in the factory and no
commissioning is required (RX1 only).
To tune the RX receiver to the frequency of the thermostat signal, follow
steps 1-5 below.
Step 1 TP5000-RF
Reset the unit by pressing and
holding -, +, V and Λtogether
until display goes blank.
Step 2 Press and hold V and +
buttons for 3 seconds (TP5000
now transmits unique signal continuously for 5 minutes).
Step 3 RX1
Press and hold buttons PROG
and CH1 for 3 seconds until green
light flashes once.
Step 4 RX2 (if applicable)
Stat 1 - perform steps 1-3.
Stat 2 - wait 5 mins, perform steps 1-2 and then press
PROG and CH2 on RX2.
RX3 (if applicable)
Stat 1 - perform steps 1-3.
Stat 2 - wait 5 mins, perform steps 1-2 and then press
PROG and CH2 on RX3.
Stat 3 - wait 5 mins, perform steps 1-2 and then press
PROG and CH3 on RX3.
Step 5 TP5000-RF
Press V or Λto select temperature - the unit will revert back
to operating mode.
Installation Instructions
GB

7
User Instructions
GB
What is a programmable room thermostat?
... an explanation for householders
A programmable room thermostat is both a programmer and a room thermostat. A
programmer allows you to set ‘On’ and ‘Off’ time periods to suit your own lifestyle. A
room thermostat works by sensing the air temperature, switching on the heating when
the air temperature falls below the thermostat setting, and switching it off once this set
temperature has been reached.
So, a programmable room thermostat lets you choose what times you want the heating
to be on, and what temperature it should reach while it is on. It will allow you to select
different temperatures in your home at different times of the day (and days of the week)
to meet your particular needs.
Turning a programmable room thermostat to a higher setting will not make the room
heat up any faster.How quickly the room heats up depends on the design of the heating
system, for example, the size of boiler and radiators.
Neither does the setting affect how quickly the room cools down. Turning a
programmable room thermostat to a lower setting will result in the room being
controlled at a lower temperature,and saves energy.
The way to set and use your programmable room thermostat is to find the lowest
temperature settings that you are comfortable with at the different times you have
chosen, and then leave it alone to do its job. The best way to do this is to set low
temperatures first,say 18°C,and then turn them up by one degree each day until you are
comfortable with the temperatures.You won’t have to adjust the thermostat further.Any
adjustments above these settings will waste energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only one
programmable room thermostat to control the whole house. But you can have different
temperatures in individual rooms by installing thermostatic radiator valves (TRVs) on
individual radiators. If you don’t have TRVs, you should choose a temperature that is
reasonable for the whole ho use. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then prevent any
overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be adjusted in spring
and autumn at the changes between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for example,‘Override’,
‘Advance’or ‘Boost’.These are explained in the manufacturer’s instructions.
Programmable room thermostats need a free flow of air to sense the temperature,
so they must not be covered by curtains or blocked by furniture. Nearby electric fires,
televisions, wall or table lamps may prevent the thermostat from working properly.

8
Your programmable room thermostat
The TP5000 allows you to programme up to 6 times and
temperatures at which your heating will come on and go off each
day. You can programme one set of times and temperatures for
weekdays and another set for weekends.
It features several user overrides including frost protection,
thermostat mode and time or temperature display.
Preset Programmes
Your TP5000 comes ready programmed with a set of operating
times and temperatures which often suit most people.
If you want to change any of these settings you can do so by
following the instructions on pages 10-11.
First,follow the steps on page 9 to set the correct time and date.
Weekdays (Mon-Fri) Weekend (Sat-Sun)
Event Time Temp °C Event Time Temp °C
1 06:30 20 1 07:00 20
2 08:30 15 2 16:00 21
3 11:30 20 3 23:00 15
4 13:30 15 4 00:00 15
5 16:30 21 5 01:00 15
6 22:30 15 6 01:59 15
User Instructions
User Instructions
GB

9
Before you start
Open the flap on the front of the
programmer.
Press the + & – AND  & buttons
simultaneously to reset the unit.
This will reinstate the preset programmes
and will set the time to 12:00 on Day 1 and
the temperature to 20°C.
Setting the Clock & Day
Note: clock is displayed in 24 hour mode.
CLOCK
Press PROG to begin programming.
Use + or - to adjust the TIME (press and
hold to change in 10 min increments).
DAY
Press PROG again.
Use + or - buttons until correct DAY is
shown (1 = Monday, 2 = Tuesday, etc).
Remember - you will have to reset
the time when the clocks change in
Spring and Autumn.
i2 00
!
User Instructions
GB

10
Please Note
The unit must be programmed in sequence and ON/OFF
times cannot be programmed out of sequence.
If you want to leave a preset time as it is, simply press PROG
to move on to the next setting.
During programming, if no buttons are pressed for 2 to 3
minutes the unit will automatically return to RUN mode,and the
programme set up to that minute will be active.
If at any time you get confused and need to reset the unit to
the preset programmes press the + & – AND  &buttons
simultaneously.
20
i2 24
Before you change the preset programmes
!
Running your programme
If you are happy to use the preset programmes on page 8, you
don’t need to do anything else.
To accept the presets close the front cover
and after 2 minutes the pre settings will
automatically be accepted (& colon will blink).
Your unit is now in RUN mode.
User Instructions
GB