Danfoss TS715 Si Assembly Instructions

TS715 Si
Installation & User Instructions
(Including 24V models)
Electronic
single channel
timeswitch
®
Certification Mark

2
INDEX
Index
Installation
Product specication 3
Installation 3-4
Wiring 4
DIL switch settings 5
Advanced Programming Options 5
Copy Functions 6-7
Service Interval Timer 7
Wiring Conversion 8-11
User
What is a programmer? 12
Your timeswitch 13
Preset programmes 13
Before you start 14
AM/PM or 24hr display 14
Setting the Time and Day 14-15
Accepting the preset programmes 15
Changing the preset programmes 16
Programming system - 5/2 day 17-18
Programming system - 7 day 19-20
Programming system - 24 hour 21
Running the programme 22
Temporary overrides 23
Holiday Programme 24
Changing clocks forward/back 25
Service Interval Timer 26
Making a full reset 27
Troubleshooting 28
Contact details 30
DAY/HOL
+1HR override
MAN override
RESET
Mode
SELECT

3
Please Note:
This product should only be installed by a qualied
electrician or competent heating installer, and should be
in accordance with the current edition of the IEEE wiring
regulations.
Specication 230V Model 24V Model
Power supply 230 Vac, ±15%,
50/60 Hz
24Vac, ±15%,
50/60Hz
Switching action
1 x SPDT voltage free, Type 1B
Switch rating 24 - 230 Vac, 3(1)A
Battery back-up 24 hours minimum
Setting/Running Accuracy ±1 minute
Dimensions, mm (W, H, D) 135 x 88 x 32
Design standard EN 60730-2-7
Control Pollution Situation Degree 2
Rated Impulse Voltage 2.5kV
Ball Pressure Test 75°C
Product specication
Installation and Specication
Installation Instructions
Installation
 Remove wallplate from unit by unscrewing the two screws
on the bottom edge of the unit.
From the top left hand corner of the wallplate, there must
be clearances of at least 140 mm to the right, 15mm to the
left, 30mm above and 100mm below in order to mount
the plug-on module.

4
The wallplate must be securely mounted either directly to
the wall using suitable wood screws or to a ush mounted
1-gang electrical accessory box using M3.5 screws.
Cable access can either be from behind for concealed
cabling, or from below for surface cabling. If surface cable
is used, cut out cable access slot on plug-on module prior
to mounting the module.
For wiring connections refer to diagram on page 5.
TS715-Si models are double insulated and do not require
an earth connection, however a parking terminal is
provided on the wallplate. This is clearly marked with an
Earth symbol.
Prior to mounting the plug-on module, DIL switches on
the rear of the plug-on module must be set. See diagram
on page 5 for available options.
Mount plug-on module to wallplate by locating tabs on
top of wallplate in apertures on rear of module, hinge
down and press rmly to wallplate before tightening
securing screws on bottom of wallplate.
Installation and Wiring
Wiring (For Wiring Conversion tables see pages 8-11)
COM OFF ON
230 V
fused 3A
TS715 (3066 12/01)
Always switch o mains rst and never t programmer
to a live wallplate.
NOTE:
Link terminals L
and 1 for standard
mains voltage
operated systems
On 24 volt models
power supply must
be wired to A & B on
wallplate.

5
DIL switch settings and Advanced Programming Options
Not Used
Not Used
5/2 Day
7 Day
Sw.1
Sw.2
Sw.3
Sw.4
Not Used
Not Used
7 Day or 24 Hour
24 Hour
Tick the INSTALLER SETTING box
on the inside ap label to notify
user in which mode their unit is
set (24hr, 5/2 day or 7 day).
DIL Switch Settings
Before mounting the unit, ensure the
4 DIL switches on the rear have been
moved to the required settings.
!INSTALLER SETTING
24 Hour
5+2 Day
7 Day
Advanced Programming Options
To enter advanced programming press PROG, +and DAY/HOL
together and hold for 5 seconds.
Option 1 - (3 or 2 On/O’s per day)
Use + or - to change between 3 and 2 on/o’s each day.
Option 2 - (Disable or enable auto time change)
Press NEXT, then use + or change between auto time change
enabled and auto time change disabled.
Option 8 - (Advanced Copy Functions)
Press NEXT, then +or -to change between the following copy
options:
(0) Standard copy in 7 day and 5+2 day.
(1) Enhanced copy in 7 day, standard copy in 5+2 day
(2) Enhanced copy in 7 day, AB copy in 5+2 day.
For an explanation of the copy features and how to use them
please see page 6.
Press PROG to return to RUN.
32
3 on/o’s each day (Factory setting) 2 on/o’s each day
Auto time change enabled (Factory setting) Auto time change disabled

6
Copy Functions Explained
There are 3 possible copy functions available. These are;
Standard Copy, Enhanced Copy, and AB copy. Copy functions
are enabled/disabled in the Advanced Programming Options
(page 5).
Standard Copy: Pressing copy will copy the previous days
events into the displayed day. The unit will then display the 1st
event for the new day. This copy function is present only if the
unit is set to run in 5+2 or 7 day mode.
Enhanced Copy: The enhanced copy function is available in 7
day mode only. This allows any day to be copied to any other
day, or days. To use the enhanced copy function go into the
event programming using the PROG button, then:
Use the DAY button to nd the day to be copied from.
Press the COPY button to select the day to be copied from.
When selected, the day should begin to ash.
Use the DAY button to nd the day to be copied to.
Press COPY button to copy the selected day.
Repeat steps 3 and 4 to select and copy other days.
To stop copying, use the DAY button to go back to the
ashing day and press the COPY button. The previously
ashing day will stop ashing to indicate it has been de-
selected.
NOTE: When a day has been copied to, it will remain visible and
not ashing when the DAY button is used to select other days.
AB Copy: The AB copy function is available in 5+2 mode only
and only if activated in the Advanced Programming setting.
A and B days, when selected, can be any group of days e.g. 5+2,
4+3 etc. The days do not have to run in sequence. For example,
to operate in a 5+2 day mode the days can be set as follows:
1.
2.
3.
4.
5.
6.
Copy Functions

7
Service Interval Timer
The TS715 Si is tted with an installer setback service interval
timer. If this feature is required please contact our technical
department. Setting instructions for this gas safety feature are
only available to bona de heating installers.
To use the AB copy function – press the PROG button:
This will show the“A”days, with all the days selected.
Use the DAY button to highlight a day.
Subsequent presses of the DAY button will increment
through the days.
Press the +button to select a specic day as an “A” day, or
press the –button to specify a day as a“B” day.
Once the day has been selected as an “A” or “B” day the
programme will automatically jump to the next day.
When the last day of the week is active, pressing +, -, or DAY
will move back to the “A” days displayed with no selected
(ashing) days (see image below).
Repeat 2 to 6 until all selections have been made.
When selections are completed, press the PROG button to
move to event programming.
Event Programming in AB mode
Programme“A”day events using the +(time advance), - (time
decrease), and NEXT (next period) buttons.
Press the DAY button to change to programme the “B” days
Programme“B”day events using the +(time advance), -(time
decrease), and NEXT (next period) buttons.
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
A Days B Days
Mon Tues Thurs Fri Sat Wed Sun
Copy Functions and Service Interval Timer

8
DANFOSS RANDALL
TS715-Si
MAINS
NL
NL
The existing wallplate may be used when replacing the following, but the wiring must b
e
between L & COM terminals of wallplate.
ACL LS111, LS711, LP111 & LP711 N L
DRAYTON TEMPUS ONE & TEMPUS TWO N L
LANDIS & GYR RWB3 N L
LANDIS & GYR RWB30 N L
The TS75/TS15 wallplate must be used to replace the existing wallplate when replacing t
h
age systems, t wire link between terminal 1 & L of wallplate.
GRASSLIN 45, 45A, 45E 2 1
HONEYWELL ST6100 N L
HORSTMANN 423 PEARL, EMERALD & TOPAZ N L
HORSTMANN KMK2A YMK2 3 4
HORSTMANN 425 CORONET N L
DANFOSS RANDALL 911 N L
DANFOSS RANDALL 103, 103E, 103E5 & 103E7 5 6
RANDALL 3020 1,7 6
DANFOSS RANDALL SET1 N L
RANDALL TSR2 3 2
PEGLER SUNVIC SP20 & SP25/30 N L
POTTERTON MYSON EP4001 N L
WIRING CONVERSIONS, (applies only to 230 volt models)
Wiring conversions for other timeswitches which can be replaced with the
Danfoss TS715-Si, refer to the second part of the table. If in any doubt, please
contact our Technical Services Department before proceeding with the
replacement.

9
LOAD An additional terminal block may be re-
quired where these disconnected leadss
(or pairs of leads) should be terminated
COM OFF SPARE ON
12 3 4 AB C D
e
reconnected as shown below. In addition, in mains voltage systems, t wire link
12 4 3
13 4 2
-3 1 4 2
23 1 4
h
e following timeswitches. Wiring details are shown below. In addition, in mains volt-
3- 4
12 3 4 - -
3- 1 4 25 6
1- 2
56 1 4 2 3
54 2 6
3- 2 1
-- 2 4 35
56 2 4
1- 4 5 67
34 S 5
52 4 AB C D

10
DANFOSS RANDALL
TS715-Si
MAINS
NL
NL
The TS75/TS15 wallplate must be used to replace the existing wallplate when replacing t
h
age systems, t wire link between terminal 1 & L of wallplate.
SANGAMO M6 4,5 6
SANGAMO 410 FORM 8 4,5 3
SANGAMO S254 FORM 2, S408 FORM 5,
S251 FORM 2 NL
SANGAMO S610 FORM 2, S611 FORM 2,
S612 FORM 2, S408 FORM 4, S408 FORM 6,
S253 FORM 2, S255 FORM 2
NMOTOR
LIVE
SANGAMO S409 FORM 8 3,N 3,L
SANGAMO S263 FORM 2
SANGAMO S264 FORM 2 NL
SMITHS IND. MKI, MKII N L
SMITHS IND. CENTROLLER 30 1 2
SMITHS IND. CENTROLLER 40 1 2
SWITCHMASTER N L
TOWERCHRON TC 2 1
VENNER VENNERETTE MKIIA N L
VENNER VENNERETTE MKIVA 2 3
VENNER VENOTIME (WITH NEON INDICATING CIRCUIT
ON) NL
VENNER VENOTIME (WITH NEON INDICATING POWER ON) N L
VENNER VENNERON, VENNERON P 3 2