Darkly Labs Emblaser 2 User manual

FUME FILTRATION
Emblaser 2 Fume Filtration User Manual 1.2
User Manual
English
Deutsch
Darkly LabsR

Filtration System Tray Hose Adaptor
Carbon Filter 2x Pre-Filters Power Cord
2. WHATS IN THE BOX
The Fume Filtration System performs two key functions; It assists the Emblaser 2’s built in exhaust
fan to evacuate fumes from the internal workspace as well as ltering the fumes to remove the
majority of contaminants, signicantly reducing air-born particles.
It is important to note that although visible contaminants are completely ltered, there will be
some odor that passes through the lters. This is normal.
IMPORTANT: The Fume Filtration Unit must be turned on when the Emblaser 2 is in operation.
1. INTRODUCTION

3. FOR YOUR SAFETY
ALWAYS USE IN A WELL VENTILATED AREA
Air vented from the fume ltration system is not safe to breathe,
especially in high concentrations. Always ensure you use it in a
well ventilated area.
Do not use in wet surroundings
Water and electricity are a dangerous
combination. Ensure your workspace is dry
and not subject to potential wet conditions.
Never use materials containing chlorine
Materials containing chlorine will produce
extremely toxic and corrosive fumes when
laser cut or engraved.
Ensure your material is safe to use
Materials react dierently to laser cutting
or engraving depending on their chemical
or physical composition. Some materials
produce harmful fumes that may not be
safely removed by the Fume Filtration
System.
Do not operate if damaged
Damage to any part of the Fume Filtration
System could compromise its safety and
cause injury. If any part of the Fume
Filtration System is damaged, contact your
reseller or Darkly Labs directly before
operation.
Never run your Emblaser 2 unattended
Do not leave unattended while running.
If you see ame or re - Immediately stop
the machine and extinguish. Not only could
a ame grow into a larger re, its heat will
cause damage to the internal mechanisms
and optics.
DO NOT USE WITH BANNED MATERIALS
The Filtration System is NOT designed to lter toxic fumes
produced from materials such as PCV, Vinyl, ABS etc. Please refer
to your Emblaser 2 User Manual for more details on materials
that may produce harmful fumes.

4. INSTALLATION
1.
Tilt the Filtration System over so that the opening on underside is visible.
Insert the Pre-Filter and tuck the edges neatly under the lip of opening.
2.
Slide the Tray into place. Take note of the four clips that must engage
If you experience diculty installing the Tray, check to make sure the Pre-lter is not in the
way.

3.
Attach the Hose Adaptor to the end of Emblaser 2 exhaust hose.
Insert the Adaptor into the Tray. (This may require some force).
4.
Connect exhaust hose to Emblaser 2

Insert supplied power lead.
5.
Turn the unit on by pressing the power button on the front.
Note: Version 2 Filtration Systems allow for 3 fan speed settings. These are set by pressing the
power button sequentially to increase the fan speed.
6.

Unlatch the clasp at rear of the Fume Filtration Unit.
Lift the upper section from base to expose Carbon Filter Cartridge.
1.
Carbon Filter Pre-Filter
5. FILTER REPLACEMENT
The Fume ltration unit uses a carbon lter cartridge. With prolonged use this cartridge
will become less ecient, we recommend replacing the lter every month or if ltering
performance reduces.
Tip: To prolong lter life, turn o Fume Filtration Unit when not in use.

Place new Carbon Filter into base
Orientate the edge with the scooped feature to face the rear of the Fume Filtration Unit.
3.
Remove the old Carbon Filter Cartridge. (This can be disposed of in conventional waste bins).
2.

Perform the following steps to correctly reassemble the top component to the base.
Locate the metal hook at the front of the top component. Engage this rst.
Using the metal hook as a hinge; swing the rear of the top component down.
4.
Apply pressure to the rear corners of the top component to pop the edges into place.
Latch the rear clasp.
5.

Slide the Tray out. Take care not to damage the four clips retaining the tray.
Remove old Pre-lter and replace with a new one. Be sure to tuck the edges of the new pre-
lter neatly under the lip of the opening.
6.
Slide the Tray back into place. Take note of the four clips that must engage.
If you experience diculty installing the Tray, check to make sure the Pre-lter is not in the
way
7.

3/99-101 Western Avenue, Westmeadows, 3049 Australia
[email protected] ●www.darklylabs.com
Copyright © Darkly Digital Pty Ltd (Darkly Labs) 2014-2017.
If you have trouble installing or operating your Fume Filtration Unit, please check our Knowledge
Base or contact us through the Help Centre.
Help Centre / Knowledge Base: https://darklylabs.com/start
Technical support
Darkly LabsR