DAS.4 SL26 User manual

SL26 User Manual

Introducon
Combining low-power Bluetooth chip and
high-tech sensor technology, the smart watch
can monitor data related to sports and health
such as walking, running, cycling, basketball,
football, table tennis, heart rate, blood pres-
sure and sleep. Meanwhile, it can synchronize
informaon such as me, weather and mes-
sages. It is also equipped with funcons such
as mobile phone loss prevenon, sedentary
reminder, and alarm clock reminder.
How to Wear
1. Refer to the figure to correctly wear the
watch.
2. Buckle the watchband according to the
comfort level (make the heart rate light
should be close to your skin surface and avoid
looseness).

Funcon Operaons
ON/OFF
ON: long press the key on the side for about 2s,
and it will power on aer a vibraon
OFF: long press the key on the side for about 2s,
and it will power off aer a vibraon.
Connect the watch to your mobile phone:
download and install “FunDo” on the phone
(two available ways):
1. IOS and Android: scan the following QR code.
Aer you open the interface, click opons in
the upper right and use your mobile browser to
open and download.
2. Android: search “FunDo” in the Y PlayStore to
download; IOS: search “FunDo” in the APP Store
to download.

Aer it is downloaded, please allow all permissions
occurred during the installaon (the watch and mobile
phone require to connect to Bluetooth 3.0 and Blue-
tooth 4.0, ensuring that all funcons can be realized).
How to connect to Bluetooth 4.0: Aer suc-
cessfully downloading the app and installing it ,
you can find a turn-on noficaon prompt aer
opening “FunDo” and mobile Bluetooth, then
click “OK”. Click “More” on the boom right to
add devices, then search “TSO2-LE” and click to
connect (note: some Android phones need you
to open its GPS funcon, otherwise, it may fail to
search the watch Bluetooth name);
How to connect to Bluetooth 3.0: Open the
main menu of the watch – Bluetooth – search
Bluetooth – select to acvate Bluetooth – click
the mobile Bluetooth name you intend to
connect to – gain Bluetooth connecon prompt
– click “OK”(allow all mobile permissions) – click
Bluetooth 3.0 to connect.
How to check whether it is successful to connect:
When you drop down the watch menu: green
Bluetooth icon indicates that Bluetooth 4.0 is
successfully connected; blue indicates that Blue-

tooth 3.0 is successfully connected; blue (the
upper part) and green (the lower part) indicate
that both Bluetooth 3.0 and 4.0 are successfully
connected.
How to set message noficaon: Enter your mo-
bile sengs – APP management – find “FunDo” –
permission management – allow all permissions
– enter noficaon management – find “FunDo”
and allow all permissions.
Open “FunDo” – more – APP noficaon –
open the background operaon permission –
enter and select “unlimited” – prompt to open
self-starng aer return – open self-starng
– return - select and open APP such as QQ and
WeChat that you want to synchronize informa-
on noficaons to the watch.
Note: if you log in to your WeChat account on
the phone and computer at the same me,
the account on the phone won’t receive any
noficaon. Some mobile phones require to add
“FunDo” in the power-saving white list, avoiding
being turned off when it is out of baery.
Fail to receive noficaons: The watch only syn-
chronizes noficaons from your mobile phone

such as call, message, QQ and WeChat. The watch
won’t receive any informaon if your mobile
phone fails to receive noficaons. At this me,
open your mobile sengs – noficaon funcon
– find the corresponding APP – allow noficaon.
Interface switch
Dial plate switch: Long press the dial plate
interface for 3s to switch dial plates. Slide the
screen le and right to switch the dial plate and
click OK to switch.
Drop down menu: Slide the dial plate interface
from the top to the boom and the interface
shows funcons such as do not disturb mode,
weather, brightness display, connecon and
sengs icon.
Measurement data interface: Slide the dial
plate from right to le to enter the interface that
checks measurement data, then you are able to
check today’s data such as walking, sleep, heart
rate and ECG.
Noficaon: Slide the dial plate interface from
le to right to enter the interface that checks
noficaons.

Aer the successful pairing with your mobile
phone, please open the switch of APP noficaon
on the APP, then noficaons received by your
mobile phone will be synchronized to the watch.
Main menu: Slide the dial plate interface from
the boom to the top to enter the main menu.
Enter each funcon and slide right to return.
Noce: somemes, unstable connecon
between mobile phone and watch Bluetooth
may occur due to the inconsistent Bluetooth
protocols of mobile brands. At this me, turn
off your mobile Bluetooth and try to connect
again (or restore the watch to factory sengs).
If system halted occurs, please long press ON/
OFF key for 10s to restart the watch.
Introducon to Main Funcons
Noficaon: Enable to check instant messages
of APP such as QQ and WeChat (such funcon
requires to connect to your mobile “FunDo”).
Pedometer: Enable to check today’s walking
steps, calorie burned and walking distance. It
will automacally save all data of the day at
24:00 and it returns to 0. Users are enabled to
check all data of the day and historical data in

the APP, and change daily walking goal in the
step counng interface.
Sports Record: In the sports record interface, users
are enabled able to check all sports data saved in the
sports mode.
ECG Monitoring: Adopng opcal heart rate and
ECG, it takes about 30s to monitor data. Aer a
successful measurement, “ToApp” will appear
in the interface. Check ECG that is saved in the
mobile app“FunDo”.
Sports Mode Monitoring: Mulple sports
modes: running, hiking, biking, basketball, Ping-
Pong and football. Click “GO” aer you enter
any sports mode, and it starts to work aer 3s.
Click the interface to connue or stop exercises.
Sports data such as the total me and calorie
burned will be displayed in the interface aer
you click to stop exercises. Enable Able to delete
or save such sports data.
QR Code: Scan the QR code to download and
install via your mobile phone
Sleep Monitoring: Record your sleep length and

quality from 9pm to 9am, helping you adjust
your metable beer and improve sleep qual-
ity. Slide up and three opons are displayed:
status (turn on or turn off), history (check deep
sleep and light sleep length), and help (instruc-
ons in detail).
Bluetooth: Search devices you intend to con-
nect to, or disconnect the device that is in the
connected state.
Heart Rate Monitoring: Get the watch close
to the wrist (the best wearing posion: the
arm part above carpal bone), and measure the
real-me heart rate value (average person:
60-90 mes/second). Click the start icon at the
boom and “it is measuring” is displayed. It
takes about 20s to measure.
Telephone Directory: Synchronize 400 contacts
from the mobile phone;
Call Record: Synchronize call records from the
mobile phone;
Message: Synchronize messages from the mo-
bile phone (don’t support IOS mobile phones);

IP68 – Only dustproof
and only accidental con-
tact with fresh water –
hand washing.
Stopwatch: Open such funcon to me once or
mulple mes;
Alarm Clock: Self-defined 5 alarm clocks: long
press to delete the alarm clock.
Dial: Connect to the mobile phone to dial (take
the call on the watch).
An-lost: Click to find and the mobile phone
will sound the alarm; or enter the mobile APP
find funcon and the watch will sound the
alarm.
www.das-4.com