Data Video ZEK-1 User manual

ZEK-1
Zoom Encoder Kit

2
Table of Contents
FCC COMPLIANCE STATEMENT......................................4
WARNINGS AND PRECAUTIONS ....................................4
WARRANTY...................................................................6
STANDARD WARRANTY ......................................................6
THREE YEAR WARRANTY.....................................................7
DISPOSAL ......................................................................7
INTRODUCTION.............................................................9
FEATURES ........................................................................9
ASSEMBLY................................................................... 10
PRODUCT PARTS .............................................................10
INSTRUCTIONS ................................................................14
EXAMPLE SETUP.......................................................... 20
CAMCORDERS WITH INCOMPATIBLE ZOOM RINGS..................22
SPECIFICATIONS .......................................................... 23
ACCESSORY LIST .......................................................... 23
SERVICE AND SUPPORT............................................... 24

3
Disclaimer of Product & Services
The information offered in this instruction manual is intended as a
guide only. At all times, Datavideo Technologies will try to give correct,
complete and suitable information. However, Datavideo Technologies
cannot exclude that some information in this manual, from time to time,
may not be correct or may be incomplete. This manual may contain
typing errors, omissions or incorrect information. Datavideo
Technologies always recommend that you double check the
information in this document for accuracy before making any purchase
decision or using the product. Datavideo Technologies is not
responsible for any omissions or errors, or for any subsequent loss or
damage caused by using the information contained within this manual.
Further advice on the content of this manual or on the product can be
obtained by contacting your local Datavideo Office or dealer.

4
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Warnings and Precautions
1. Read all of these warnings and save them for later
reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit
may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are
provided for ventilation. To ensure safe and reliable operation of
this unit, and to protect it from overheating, do not block or cover
these openings. Do not place this unit on a bed, sofa, rug, or
similar surface, as the ventilation openings on the bottom of the
cabinet will be blocked. This unit should never be placed near or
over a heat register or radiator. This unit should not be placed in a
built-in installation unless proper ventilation is provided.
7. This product should only be operated from the type of power
source indicated on the marking label of the AC adapter. If you
are not sure of the type of power available, consult your
Datavideo dealer or your local power company.
8. Do not allow anything to rest on the power cord. Do not locate
this unit where the power cord will be walked on, rolled over, or
otherwise stressed.

5
9. If an extension cord must be used with this unit, make sure that
the total of the ampere ratings on the products plugged into the
extension cord do not exceed the extension cord rating.
10. Make sure that the total amperes of all the units that are plugged
into a single wall outlet do not exceed 15 amperes.
11. Never push objects of any kind into this unit through the cabinet
ventilation slots, as they may touch dangerous voltage points or
short out parts that could result in risk of fire or electric shock.
Never spill liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not
attempt to service this product yourself. Opening or removing
covers that are marked “Do Not Remove” may expose you to
dangerous voltage points or other risks, and will void your
warranty. Refer all service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified
service personnel under the following conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal
operating conditions. Adjust only those controls that are
covered by the operating instructions in this manual;
improper adjustment of other controls may result in damage
to the unit and may often require extensive work by a
qualified technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been
damaged;
f. When the product exhibits a distinct change in performance,
indicating a need for service.

6
Warranty
Standard Warranty
Datavideo equipment is guaranteed against any manufacturing
defects for one year from the date of purchase.
The original purchase invoice or other documentary evidence
should be supplied at the time of any request for repair under
warranty.
The product warranty period beings on the purchase date. If the
purchase date is unknown, the product warranty period begins on
the thirtieth day after shipment from a Datavideo office.
All non-Datavideo manufactured products (product without
Datavideo logo) have only one year warranty from the date of
purchase.
Damage caused by accident, misuse, unauthorized repairs, sand,
grit or water is not covered under warranty.
Viruses and malware infections on the computer systems are not
covered under warranty.
Any errors that are caused by unauthorized third-party software
installations, which are not required by our computer systems, are
not covered under warranty.
All mail or transportation costs including insurance are at the
expense of the owner.
All other claims of any nature are not covered.
All accessories including headphones, cables, batteries, metal parts,
housing, cable reel and consumable parts are not covered under
warranty.
Warranty only valid in the country or region of purchase.
Your statutory rights are not affected.

7
Three Year Warranty
All Datavideo products purchased after July
1st, 2017 qualify for a free two years
extension to the standard warranty,
providing the product is registered with
Datavideo within 30 days of purchase.
Certain parts with limited lifetime expectancy such as LCD panels,
DVD drives, Hard Drive, Solid State Drive, SD Card, USB Thumb
Drive, Lighting, Non-PCIe Card and third party provided PC
components are covered for 1 year.
The three-year warranty must be registered on Datavideo's official
website or with your local Datavideo office or one of its authorized
distributors within 30 days of purchase.
Disposal
For EU Customers only - WEEE Marking
This symbol on the product or on its packaging
indicates that this product must not be disposed
of with your other household waste. Instead, it is
your responsibility to dispose of your waste
equipment by handing it over to a designated
collection point for the recycling of waste
electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to
conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment. For more
information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.

8
CE Marking is the symbol as shown on the left of
this page. The letters "CE" are the abbreviation of
French phrase "Conformité Européene" which
literally means "European Conformity". The term
initially used was "EC Mark" and it was officially
replaced by "CE Marking" in the Directive 93/68/EEC in 1993. "CE
Marking" is now used in all EU official documents.

9
Introduction
ZEK-1 Zoom Encoder Kit is an electromechanical device that
adds automatic zoom positioning to the camcorder mounted
on PTR-10/10T MARK II Robotic Pan Tilt Head.
Please note that ZEK-1 does not work with PTR-10/10T.
Features
Automatic zoom positioning
Flexible mount positions
Two gears provided for M0.6 and M0.8 zoom rings
Gear A
Gear B
Gear Module
M0.6
M0.8 (with Gear Ring)
Compatible
Camcorder
Models
Sony Z280
Sony X200
Sony EX-3
Canon XF705
Panasonic AG-
HPX255

10
Assembly
There are two sections in this chapter. We will describe
different parts of the ZEK-1 in the first section and the assembly
procedure will be outlined in the second section.
Product Parts
The table below lists all the parts that you will find in the
product package.
Name
Descriptions

11
Zoom Encoder
The gear should engage with the
camcorder’s zoom ring and the 4-pin
mini-DIN connector should be
connected to the Zoom Sensor port on
the PTR-10/10T MARK II. The snap-and-
lock mini-din connector of the remote
cable will be securely fastened once
plugged into the Remote port. To
remove, use two fingers to gently hold
the part of the plug labelled by two
arrows then pull the connector
outward.
Note: The size of the gear attached to
the zoom encoder is M0.8. A spare
screw and an M0.6 gear are provided in
a plastic zipper bag. The size of the gear
used should match the size of the zoom
ring on your camcorder.

12
Metal Bar
The metal bar holds the zoom encoder
in place.
Bar Holder
Insert the metal bar into the bar holder.
Spare M0.6 Gear
Designed for M0.6 Zoom Ring.

13
Camera Mount
Plate
The camera mount plate should be
mounted on the PTR-10/10T Mark II
Note: The rubber pad provided should
be affixed to the surface on which the
camcorder is placed as it reduces the
friction between the camcorder and
the plate.
Gear Ring Belt
designed for use
with M0.8 gear
Wrap the gear ring belt around the
camcorder’s zoom ring if it is neither
M0.6 nor M0.8. Then use the M0.8 gear
to engage with the belt.

14
Instructions
Step 1
Remove the PTR-10/10T Mark II’s camera mount plate by
unfastening the three screws as indicated by the arrows shown
in the diagram below.

15
Step 2
Use the three screws of Step 1 to secure the ZEK-1’s camera
mount plate to the PTR-10/10T Mark II as shown below.

16
Step 3
As shown in the diagram below, insert one end of the metal bar
into the bar holder and another end of the metal bar into the
zoom encoder then tighten.

17
Step 4
If you are using camcorders like Sony Z280, use the three
screws provided in the plastic zipper bag to secure the bar
holder along with the metal bar and the zoom encoder to the
tilt arm as shown in the diagram below. Ensure the gear
attached to the zoom encoder engages with the camcorder’s
zoom ring.
Zoom Encoder
Camera Mount Plate
Tilt Arm
Metal Bar
Bar Holder

18
If you are using camcorders like Panasonic CX350 and Canon
XF705, use the three screws provided in the plastic zipper bag
to secure the bar holder along with the metal bar and the zoom
encoder to the camera mount plate as shown in the diagram
below. Ensure the gear attached to the zoom encoder engages
with the camcorder’s zoom ring.
Note: Use the gear ring belt if your camcorder’s zoom ring is
neither M0.6 nor M0.8. Simply wrap the gear ring belt around
the zoom ring then tighten.
Bar Holder
Metal Bar
Tilt Arm
Camera Mount Plate
Zoom Encoder

19
Step 5
Connect the 4pin mini-DIN cable connector of the zoom
encoder to the Zoom Sensor port on the PTR-10/10T MARK II to
complete the installation.

20
Example Setup
Sony Z280