Data Video SE-2000 User manual

Digital Video Switcher
SE-2000
INSTRUCTION MANUAL
www.datavideo-tek.co
m

2
Contents
Warnings and Precautions.......................................................................................................................... 4
Warranty........................................................................................................................................................ 5
Standard Warranty................................................................................................................................... 5
Two Year Warranty.................................................................................................................................. 5
Disposal................................................................................................................................................... 5
Packing List ............................................................................................................................................. 5
Introduction .................................................................................................................................................. 6
Product Overview .................................................................................................................................... 6
Features................................................................................................................................................... 6
Connections & Controls.............................................................................................................................. 7
Keyboard ................................................................................................................................................. 7
Audio mixer ......................................................................................................................................... 8
Audio Input Source Selectors and Level Controls .............................................................................. 8
Audio LED Meters .............................................................................................................................. 8
Audio Monitor Button .......................................................................................................................... 8
System Configuration Menu ............................................................................................................... 9
Logo Setting ....................................................................................................................................... 9
PIP / KEY ............................................................................................................................................ 9
Transition Effects ................................................................................................................................ 9
Transition Speed ................................................................................................................................ 9
CUT .................................................................................................................................................... 9
TAKE .................................................................................................................................................. 9
T-Bar ................................................................................................................................................. 10
Main Source ..................................................................................................................................... 10
Sub Source ....................................................................................................................................... 10
Headphone ....................................................................................................................................... 10
Headphone Volume Control ............................................................................................................. 10
Rear Panel............................................................................................................................................. 11
Rear Panel Connections .................................................................................................................. 11
Multi Preview Output.................................................................................................................................. 13
Main Source and Sub Source Rails....................................................................................................... 14
Transition Effects................................................................................................................................... 14
System Configuration Menu ..................................................................................................................... 15
Menu and Navigation............................................................................................................................. 15
USER’S PROFILE ............................................................................................................................ 15
INPUT SETTINGS ............................................................................................................................ 15
PIP SETTING ................................................................................................................................... 16
LUMA SETTING ............................................................................................................................... 16
LOGOS ............................................................................................................................................. 16
MODE SETTING .............................................................................................................................. 17
MONITOR MODE ............................................................................................................................. 17
INPUT 4 MODE ................................................................................................................................ 17
MASTER USER SETTING ............................................................................................................... 17
SOFT EDGE ..................................................................................................................................... 17
AUTO TAKE SPEED ........................................................................................................................ 17
BACKGROUND ................................................................................................................................ 18

3
BLACK & BARS POS.RIGHT ........................................................................................................... 18
FACTORY SETTINGS ..................................................................................................................... 18
CLOCK SETTINGS .......................................................................................................................... 18
MAX BUTTON BRIGHTNESS ......................................................................................................... 18
TWO WAY T-BAR MODE ................................................................................................................ 18
Audio Inputs and Levels............................................................................................................................ 19
A+V........................................................................................................................................................ 19
Example SE-2000 Set Ups......................................................................................................................... 20
SE-2000 Configuration Utility.................................................................................................................... 21
Storing New Logos ................................................................................................................................ 21
How to change the input source labels ................................................................................................. 22
Setting up a Luma Key overlay with PowerPoint.................................................................................... 23
HD-SDI Cabling Advice.............................................................................................................................. 24
How to update SE-2000 firmware ............................................................................................................. 25
SE-2000 bespoke Tally cabling advice..................................................................................................... 27
SE-2000 RS-232 Remote Control Protocol .............................................................................................. 28
Communication diagram........................................................................................................................ 28
Control Interface.................................................................................................................................... 28
Pin Assignment...................................................................................................................................... 28
Command Code Format........................................................................................................................ 28
Response Code Format ........................................................................................................................ 28
CRC (CRCL,CRCH) .............................................................................................................................. 29
Table 1. Lower CRC byte calculation coefficients.(Hex)....................................................................... 31
Table 2. Higher CRC byte calculation coefficients.(Hex........................................................................ 32
Table 3. Command Type....................................................................................................................... 33
Table 4. Response Code....................................................................................................................... 34
Table 5. Status Code (41 Bytes reference pages 35 & 37)................................................................... 35
Optional Datavideo Accessory Items for the SE-2000 ........................................................................... 38
Specifications............................................................................................................................................. 39
Service and Support .................................................................................................................................. 40
Disclaimer of Product and Services
The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to give correct,
complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time,
may not be correct or may be incomplete. This manual may contain typing errors, omissions or incorrect information. Datavideo Technologies
always recommend that you double check the information in this document for accuracy before making any purchase decision or using the
product. Datavideo Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage caused by using the
information contained within this manual. Further advice on the content of this manual or on the product can be obtained by contacting your
local Datavideo Office or dealer.

4
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe and
reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do
not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the
cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit
should not be placed in a built-in installation unless proper ventilation is provided.
7. This product should only be operated from the type of power source indicated on the marking label of the
AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be
walked on, rolled over, or otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the
products plugged into the extension cord do not exceed the extension cord’s rating.
10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed
15 amperes.
11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch
dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill
liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself.
Opening or removing covers that are marked “Do Not Remove” may expose you to dangerous voltage
points or other risks, and will void your warranty. Refer all service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified service personnel under the following
conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions. Adjust only
those controls that are covered by the operating instructions in this manual; improper adjustment
of other controls may result in damage to the unit and may often require extensive work by a
qualified technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f. When the product exhibits a distinct change in performance, indicating a need for service.
We recommend that you only use the SE-2000 Configuration Utility to add/write new Logos as changing any other settings
without guidance may cause the mixer or its set up menus to become un-usable. See Page 19.

5
Warranty
Standard Warranty
• Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of
purchase.
• The original purchase invoice or other documentary evidence should be supplied at the time of any
request for repair under warranty.
• Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered by this
warranty.
• All mail or transportation costs including insurance are at the expense of the owner.
• All other claims of any nature are not covered.
• Cables & batteries are not covered under warranty.
• Warranty only valid within the country or region of purchase.
• Your statutory rights are not affected.
Two Year Warranty
•
All Datavideo products purchased after 01-Oct.-2008 qualify for a free one year extension to the standard
Warranty, providing the product is registered with Datavideo within 30 days of purchase. For information on
how to register please visit www.datavideo-tek.com or contact your local Datavideo office or authorized
Distributors
•
Certain parts with limited lifetime expectancy such as LCD Panels, DVD Drives, Hard Drives are only
covered for the first 10,000 hours, or 1 year (whichever comes first).
•
Any second year warranty claims must be made to your local Datavideo office or one of its authorized
Distributors before the extended warranty expires.
Disposal
For EU Customers only - WEEE Marking
This symbol on the product indicates that it should not be treated as household waste. It must
be handed over to the applicable take-back scheme for the recycling of Waste Electrical and
Electronic Equipment. For more detailed information about the recycling of this product, please
contact your local Datavideo office.
Packing List
Items
Description
Q’ty
1 SE-2000 1
2 AC Power Cord 1
3 AC/DC Switching Adaptor 12V DC 5A 1
4 SE-2000 Instruction Manual 1

6
Introduction
Thank you for purchasing the Datavideo SE-2000 Digital Video Switcher. We hope you will be pleased with your
purchase, and with what you can achieve with this switcher. In order to get the most out of your new switcher, we
recommend that you spend some time getting familiar with this manual, as it will describe all the functions of this
unit. In addition, you’ll find some useful background information on video and audio.
Product Overview
The Datavideo SE-2000 is a rugged and very portable five channel full HD video & audio switcher designed to
excel in a new demanding high-definition production environment.
The brand new SE-2000 switcher not only meets your request for true full 1920 x 1080 HD quality, but also
provides an array of simple-to-operate features, including up to 14 pre-stored logos, digital clock display, five user
setup, DVI-D connection for use with presentation software and easy titling, and many more features.
Whether you're working in worship, education are conducting a live outside broadcast or shooting inside a
production studio, the Datavideo SE-2000 full HD video and audio switcher enables you to switch seamlessly
between video and audio sources and blend high-quality digital content on the fly, even without external genlock,
thanks to the built in TBC.
Features
 FULL HD:
Input:
 4x HD-SDI with 1x DVI-D input (Optional - See page 18 for example set up)
Or
 3x HD-SDI, with 2x DVI-D inputs (Optional - See page 18 for example set up)
Output:
 PGM: Full HD output, HD-SDI and HD-YUV format
 PVW: DVI-D
 Multi Image Preview output with Digital Clock, selected Transition and User profile display.
 DVI-D for Power point presentation, simple titling and overlays, also supports full HD input.
 LOGO and CLOCK insertion. Display 2 Logos or a Logo and the Clock on the PVW and PGM outputs.
 Store and select from 14 user created Logos (accepted size 256x192 pixels, TGA or BMP)
 4 channel input audio mixer with XLR in/out connectors.
 A+V Audio follows Video switching operation.
 Single or Two Way T-BAR operation via menu option
 LUMA Key
 PIP, FRZ, Black image
 5 individual Speed keys for instant selection with TAKE effect
 13 Transition effects (12 WIPE & 1 MIX) with soft (SFT) border option
 Memory presets for up to 5 users or configurations
 Tally output
 RS-232 control
 DC 12V 5A input

7
Connections & Controls
Keyboard
8
12
11
10
9
7
6
3
4
5
1
1. Audio mixer
2. Audio input selectors / Level Controls
3. Audio meters
4. Menu and Controls
5. Logo & Clock Selection
6. Video Effect: PIP / KEY
2
7. Transition Speed
8. Transition Effects
9. CUT & TAKE
10. T-Bar
11. Main and Sub Source selection
12. Headphone Monitoring & Volume Control

8
Audio mixer
These CH1~CH4 Audio Level Faders are for controlling the CH1~CH4 audio
mix.
These faders correspond to the Audio Source selector buttons and control
the relative volume of each input in the master output as well as the master
output level. They are called faders because they are used to decrease
(rather than increase) the signal levels to create a balanced and pleasing
mix. When the CH1~CH4 Audio Level Faders are set at -6dB, or Unity, they
pass the audio signal through at the same level as when it entered the bus.
This is why the level setting at the Input Bus is so important.
MASTER: This Slider is for controlling the audio level for the Mixed audio
output.
Audio Input Source Selectors and Level Controls
This section of the SE-2000 controls which audio input channel (CH1~CH4)
will be sent to the Audio Bus and its associated Fader.
This row of audio channel selection buttons has LEDs built in to show which
input channel is active. Level control for each audio input source is via the
rotary pots above each of the audio channel selection buttons.
A+V:
When this button is engaged or lit, the audio associated with a selected
video input source automatically follows the video through any transition
between the Main and Sub Sources. When the A+V button is inactive, the
audio sources must be switched manually. For more information, see A+V
(Page 17).
Audio LED Meters
These meters play a vital part in correctly setting the audio levels to avoid
clipping or other distortion.
The LED style Audio meters, show the signal strength at the Audio Output.
The signal they measure is determined by the sources selected by the Audio
Bus selectors and the levels set by the rotary pots and faders.
Audio Monitor Button
Use the Headphone section to monitor any of the sources (CH1, CH 2, CH3,
CH4) or “Master” output. Repeated presses of the Headphone Audio Monitor
button will cycle through the monitoring choices. In many cases, headphones
may be a more useful and accurate choice than speakers for audio
monitoring.

9
System Configuration Menu
Press the Menu button in the SE-2000 function section to enter the System
Configuration Menu. Press the u
p
,down, left, and right arrow buttons to
navigate the menu options and to change values. Use the ENT button to
save and confirm any setting that has been amended.
Logo Setting
Press the Logo1, Logo2 or Clock buttons to display the selected function on
the PVW and PGM screens. See Storing New Logos (Page 19)
Logo1 and Logo2 or Logo1 and the Clock can both be selected at the same
time. Logo2 and the Clock cannot be selected/displayed at the same time.
PIP / KEY
LUMA PVW and LUMA PGM
A Luma key can be performed between 2 inputs and the result sent to the
PVW and PGM display channels. See Setting up a LUMA Key (Page 20)
SET
If you want to enable the PIP function, you must first press the SET key, then
press the PIP PVW key and then select the Sub Source channel for the PIP
window. The size and position of the window can be set within the System
Configuration Menu. See PIP SETTING (Page 14)
PIP PVW
Allows the user to see what the PIP window will look like and make any
adjustments before the PIP window is taken to the PGM output. Pressing the
PIP PVW button toggles the PIP window on and off using a simple dissolve.
PIP PGM
Once the PIP window is ready to be taken to air the PIP PGM button will
allow a simple dissolve in and out over the top of the current program output.
Transition Effects
There are 10 Transition Effects keys. Six of these keys relate to the available
types of WIPE effect. INV (Invert) changes the direction of the chosen WIPE.
SFT changes the softness of the WIPE edge. FRZ freezes the current PGM
image until toggled off or CUT away. MIX is a dissolve effect between the
PVW and PGM sources.
For more information, see Transition Effects (Page 12).
Transition Speed
Five buttons used to choose different speeds for a transition effect when
using the TAKE button to switch between PVW and PGM sources.
CUT
Forces an immediate switch between the selected main and sub sources.
The
selected sub source becomes the main program output with no
transition effect applied.
TAKE
Starts an automated switch between the main and sub sources. The
selected sub source becomes the main program output with the selected
Transition Effect applied at the selected Effect Speed.

10
T-Bar
The T-Bar is used to carry out a manual transition such as a wipe, fade,
mix or key. When it has travelled as far as it can go the transition is
complete.
How to calibrate the T-bar:
1. Turn off the SE-2000 power, and push the T-Bar up as far as it can go to its
Top or AIR position then move the T-Bar back down by 2mm.
2. Press and hold in the SET and SUB SOURCE 1 buttons at the same time.
3. Have a colleague turn on the SE-2000 power. When the SET button and
SUB SOURCE 1 buttons are illuminated yellow release both buttons.
4. Push down the T-Bar as far as it can go to its bottom or PVW position and
then move the T-Bar back up by 2mm. Now press the CUT button.
5. Again push the T-Bar up as far as it can go to its Top or AIR position. Now
press the TAKE button.
6. Press SET button again to end the calibration process.
WARNING: If you do not follow the T-Bar calibrating steps correctly the
T-Bar may work incorrectly
Main Source
Used to select which of the source input channels or backgrounds that are
sent to the Main video PROGRAM output. For more information, see Video
Source (Page 12).
Sub Source
Used to select which of the source input channels or backgrounds will be
transitioned to or used as a sub source in an effect such as PIP.
Headphone
Accepts a stereo mini jack plug for stereo headphones. Used with the Audio
Monitor Button. The headphone volume is adjusted by the rotating Head
phone volume control.
Headphone Volume Control
Controls Headphone volume level.
Use the Headphone section to accurately monitor any of the sources ( CH1,
CH2, CH3, CH4 or “Master” ) output.

12
6. HD- SDI OUT
4:2:2 SDI Video data supports SMPTE 292M standard at 1.5G Mbps.
SDI transfers professional level video signals and it’s can connect to
long distance transmission systems.
7. HD- YUV OUT
HD- YUV component analogue output connectors.
8. MULTI PREVIEW OUT
DVI-D digital signal preview output connector (PVW).
9. DC IN
DC in socket connect the supplied 12V 5A PSU to this socket. The
connection can be secured by screwing the outer fastening ring of the
DC In plug to the socket.
10. POWER
Switches the power On / Off.
11. AUDIO OUT
Supports two channels XLR Balanced Audio output.
12. AUDIO IN
The SE-2000 supports four XLR Balanced Audio Input channels.
There are two kinds of switches under AUDIO IN:
The LINE/MIC switch is used to set the audio as LINE in or MIC in.
The 48V ON/OFF switch is for phantom power. If you want to use MIC
in, please set the LINE/MIC switch first, and then if using a Condenser
microphone turn ON the 48V ON/OFF switch. If you wish to use a
Dynamic microphone please turn OFF the 48V ON/OFF switch.

14
Main Source and Sub Source Rails
The Main Source Rail shows the active channel, this is the Live output. The active channel will also appear as the
Program Output (PGM). You can immediately switch or CUT from one input channel to another directly on the
Main Source Rail, you will see the PROGRAM Output switch as you press different keys along this rail. As each
key is selected or pressed it will turn Red.
The Sub Source Rail shows the Cued channel, the selected channel will appear in the Preview window. The
selected key will turn Yellow. The Sub Source selection determines which input will be transitioned to when using
any of the transition controls and provides the Sub Source video for Picture in Picture and Key functions.
Transition Effects
1
WIPE from upper Left corner to lower Right corner of screen
2
WIPE from Left to Right of screen
3
WIPE from Top to Bottom of screen
4
WIPE from upper Right corner to lower Left corner of screen
5
WIPE from outside edge of screen to centre of screen
6 WIPE from Left and Right hand sides into the center of the screen
7 SFT Controls the border softness of the WIPE or effect.
8 MIX Also
known as a fade or dissolve, is a transition where all the pixels of one source are
replaced by all the pixels of another, at a smooth rate, and at the same time.
9 INV Inverts the WIPE direction – the chosen WIPE moves in the opposite direction.
10 FRZ This freezes the PGM video, press it again, and it returns to the selected Live PGM source.

15
System Configuration Menu
Menu and Navigation
Press the MENU button in the Function section of the SE-2000’s keyboard to enter the System Configuration
Menu. The menu will be displayed on the SE-2000’s Multi Preview output as below.
Press the UP, DOWN,LEFT and RIGHT arrow buttons to highlight or select a menu option. Then use the UP and
DOWN arrow buttons to change the value of the selected item or option. Press the ENT button to Enter and save
your chosen value for the selected menu item.
USER’S PROFILE
- Press the MENU button and highlight the USER’S PROFILE option.
- Press the arrow RIGHT button and select a profile number by using the UP and DOWN arrows.
- Press the ENT button to confirm the chosen profile number to be used.
The current user will also be confirmed between PREVIEW and PROGRAM windows on the Multi
Preview Display.
- Up to 6 User Profiles can be configured and saved. These profiles are numbered 0 ~ 5.
- User’s Profile 0 is also referred to as the BASIC or MASTER USER settings profile.
If there are settings that will be common to all user profiles 1 ~ 5 then they are set here first under BASIC
and then these common settings can be copied to the other user profiles (1 ~ 5) by selecting LINK TO
BASIC. Then while adjusting USER 1 ~ 5, you can refer to the BASIC settings, thus avoiding multiple and
repeated adjustments for all remaining user profiles.
- Any changes made to the SE-2000’s configuration will be saved to the currently selected profile.
- The default user profile at Power On is the last selected profile used.
INPUT SETTINGS
- Press the MENU button and highlight the INPUT SETTINGS option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- BRIGHTNESS: adjustment range from -7 to +7
- CONTRAST: adjustment range from -7 to +7
- SATURATION: adjustment range from -7 to +7
- MASTER USER SETTING: When selected, the values for the above are copied from the BASIC profile.

16
PIP SETTING
- Press the MENU button and highlight the PIP SETTING.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- X- POSITION: adjustment range from 0 to +102 (when MODE SETTING is 1080i)
- Y- POSITION: adjustment range from +113 to 0 (when MODE SETTING is 1080i)
- X- POSITION: adjustment range from 0 to +70 (when MODE SETTING is 720p)
- Y- POSITION: adjustment range from +77 to 0 (when MODE SETTING is 720p)
- SIZE: adjusts the size of the smaller PIP window using a range from +1 to +97
- MASTER USER SETTING: When selected, the values for the above are copied from the BASIC profile.
If you want to enable the PIP function, you must first press the SET key in the PIP / KEY section of the
SE-2000 keyboard, then press the PIP PVW key and then select the Sub Source channel required for the
PIP window.
The PIP window will appear on the PREVIEW and PROGRAM displays when PiP PVW and PiP PGM
buttons are lit on the SE-2000’s Keyboard.
LUMA SETTING
- Press the MENU button and highlight the LUMA SETTING option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- You can set the value for the LUMA LEVEL (0 Black to 255 White)
- This LUMA LEVEL keys out a grey scale range between 0 and the LUMA LEVEL value set.
- So LUMA LEVEL 20 would key out a range of Black between 0 and 20 from the Sub source.
- MASTER USER SETTING: When selected, the value for the above is copied from the BASIC profile.
LOGOS
- Press the MENU button and highlight the LOGOS option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- You can select a pre-loaded Logo from the SE-2000’s 14 memory slots for Logo1 and Logo2.
- You can set the on screen positions of Logo1, Logo2 and the Clock.
- X- POSITION: adjustment range from 0 to +114 (under 1080i)
- Y- POSITION: adjustment range from +112 to 0 (under 1080i)
- X- POSITION: adjustment range from 0 to +72 (under 720p)
- Y- POSITION: adjustment range from +150 to 0 (under 720p)
- Accepted Logo sizes 256x192 pixels, 512x96 pixels or 128x384 pixels
- MASTER USER SETTING: When selected, the values for the above are copied from the BASIC profile.
Logos need to be loaded into the 14 memory slots in preparation before an event – See Storing
New Logos (Page 21).

17
MODE SETTING
- Press the MENU button and highlight the MODE SETTING.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This Mode setting is used to adjust the HD input mode.
- HD Mode values can be 1080/50i - 1080/60i - 1080/59.94i - 720/50p - 720/60p or 720/59.94p
- MASTER USER SETTING: When selected, the values for the above are copied from the BASIC profile.
- Please ensure your HD input source(s) match the HD mode of the SE-2000.
The selected HD mode is confirmed between the PREVIEW and PROGRAM windows on the Multi
Preview Display.
MONITOR MODE
- Press the MENU button and highlight the MONITOR MODE option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This mode adjusts the Multi Preview DVI-D output between 1080i 60Hz and 720p 60Hz.
- MASTER USER SETTING: When selected, the values for the above are copied from the BASIC profile.
INPUT 4 MODE
- Press the MENU button and highlight the INPUT 4 MODE option.
- Press the arrow buttons to select an input option and press the ENT to confirm the setting.
- This mode is used to switch INPUT 4 from HD-SDI input to DVI-D input and vice versa.
- MASTER USER SETTING: When selected, the values for the above are copied from the BASIC profile.
The changed setting will also be confirmed between PREVIEW and PROGRAM windows on the Multi
Preview Display.
MASTER USER SETTING
- Press the MENU button and highlight the MASTER USER SETTING option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This mode is used to return the SE-2000 BASIC profile (USER 0) to its factory default settings.
- If the BASIC profile is changed then any USER profiles (1 ~ 5) linked to BASIC will also be changed.
SOFT EDGE
- Press the MENU button and highlight the SOFT EDGE option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
This mode is used to set the size of the soft border (SFT Key) when using a WIPE transition or the PIP
effect.
AUTO TAKE SPEED
- Press the MENU button and highlight the AUTO TAKE SPEED option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This adjusts the different speeds of the selected transition effect when the TAKE button is used.

18
BACKGROUND
- Press the MENU button and highlight the BACKGROUND option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This option sets the background colour of the Multi Preview screen – options are Black, Grey or Blue.
BLACK & BARS POS.RIGHT
- Press the MENU button and highlight the BLACK & BARS POS.RIGHT option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This option allows the user to change the order of the keys on the Main and Sub Source rails.
- When selected the order of the keys will be BLK, BAR, 1, 2, 3, 4, DVI instead of the original sequence.
- Once changed the Key Cap Legends can be carefully removed and relocated to the new position.
FACTORY SETTINGS
- Press the MENU button and highlight the FACTORY SETTINGS option.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This menu option is used when it is required to return the product back to its factory state.
- If you select this option then ALL user settings (BASIC and 1 to 5) are returned to their factory defaults.
CLOCK SETTINGS
- Press the MENU button and highlight the CLOCK SETTINGS.
- Press the arrow buttons to select an item and press the ENT to confirm the setting.
- This mode is used to set the clock within the SE-2000.
The current Clock value is displayed in between the PREVIEW and PROGRAM windows of the Multi
Preview Display.
MAX BUTTON BRIGHTNESS
- Press the MENU button and highlight the MAX BUTTON BRIGHTNESS option.
- Press the arrow buttons to select an ON or OFF state and press the ENT to confirm the setting.
- This menu option is used when the Keyboard button back lights needs to be dimmed or made brighter.
-
TWO WAY T-BAR MODE
- Press the MENU button and highlight the TWO WAY T-BAR MODE option.
- Press the arrow buttons to select an ON or OFF state and press the ENT to confirm the setting.
- This menu option is used to change the T-BAR from one way to two way operation or vice versa.

19
Audio Inputs and Levels
Analogue audio comes into the SE-2000 through the XLR connectors on the rear panel (see above diagram). The
SE-2000 supports four XLR Balanced Audio Input channels.
There are two kinds of switches next to each XLR input under AUDIO IN:
The LINE/MIC switch is used to set the audio as LINE in or MIC in.
The 48V ON/OFF switch is for Phantom power. If you want to use MIC in, please set the LINE/MIC switch first,
and then if using a Condenser microphone* turn ON the 48V ON/OFF switch. If you wish to use a Dynamic
microphone please turn OFF the 48V ON/OFF switch.
*NOTE: Always double check the manual for the microphone being used to see what advice it gives
regarding power as some Mics have internal batteries too.
A+V
The Audio Input Channel Selectors and Level pots are the first stage in
the audio signal path. Each channel carries the audio associated with a
video input channel. When the A+V button is active, the audio follows the
video through a transition. This means that when this LED is lit, only one
channel of the Audio input section (CH1, CH2, CH3, CH4) can be
activated at a time. When the transition is a CUT, the audio will switch
abruptly at the same time.
Try this: With the A+V button engaged or lit, select Channel 2 on the Main Source bus (of course, you must have
a valid video and audio source connected). Notice that CH2 is lit in the Audio Source section. Now, select channel
1 on the Sub Source bus. Work the T-Bar to manually perform a transition (if no specific transition is selected, the
sources will dissolve) and watch Audio Input Source channel change from CH2 to CH1, following the video.
When the A+V button is not engaged or off, you can manually select which of the 4 Audio input channels will be
applied to the Video bus at the Fader. In fact, you have to select one or more of these channels, or there will be
no audio present at the audio out connections.
The A+V button should be inactive while doing level settings at the beginning-of-session so that you can select an
input and adjust the initial level correctly.
NOTE: Audio cannot be de-embedded by the SE-2000 from a HD-SDI input and Audio will not be
embedded into the SE-2000’s HD-SDI PGM outputs. For ideas on how best to do this before and after the
SE-2000 mixer see Example SE-2000 Set Ups (Page 20).

20
Example SE-2000 Set Ups