Data Video SE-650 User manual

1

2
Table of Contents
FCC COMPLIANCE STATEMENT...........................................................................................................5
WARNINGS AND PRECAUTIONS .........................................................................................................5
WARRANTY........................................................................................................................................6
STANDARD WARRANTY.................................................................................................................................6
TWO YEAR WARRANTY.................................................................................................................................6
DISPOSAL ...........................................................................................................................................6
CHAPTER 1 INTRODUCTION.............................................................................................................7
1.1 FEATURES .......................................................................................................................................7
1.2 SYSTEM DIAGRAM ............................................................................................................................8
CHAPTER 2 CONNECTIONS AND CONTROLS.....................................................................................9
2.1 REAR PANEL ....................................................................................................................................9
2.2 FRONT PANEL ................................................................................................................................11
CHAPTER 3 OSD MENU..................................................................................................................17
3.1 START ..........................................................................................................................................17
3.1.1 Transition...............................................................................................................................17
3.1.2 Type .......................................................................................................................................17
3.1.3 Wipe Effects ...........................................................................................................................17
3.1.4 Border ....................................................................................................................................18
3.1.5 Position ..................................................................................................................................18
3.1.6 Matte .....................................................................................................................................18
3.2 KEYER ..........................................................................................................................................18
3.2.1 Keyer ......................................................................................................................................18
3.2.2 Keyer Control .........................................................................................................................18
3.2.3 Key Source..............................................................................................................................19
3.2.4 Fill Source...............................................................................................................................19
3.2.5 CK Setup.................................................................................................................................19
3.2.6 Mask ......................................................................................................................................20
3.3 P-IN-P .........................................................................................................................................20
3.3.1 P-In-P Source..........................................................................................................................20
3.3.1 Position ..................................................................................................................................21
3.3.2 Border ....................................................................................................................................21
3.3.3 Crop........................................................................................................................................21
3.4 P-IN-P KEYER ................................................................................................................................21
3.4.1 P-In-P Source..........................................................................................................................22
3.4.2 Keyer ......................................................................................................................................22
3.4.3 Keyer Control .........................................................................................................................22
3.4.4 CK Setup.................................................................................................................................22
3.4.5 Mask ......................................................................................................................................23

3
3.5 LOGO ...........................................................................................................................................23
3.5.1 Logo Image ............................................................................................................................23
3.5.2 Logo Control...........................................................................................................................23
3.5.3 Logo Source (Logo Src)...........................................................................................................23
3.5.4 Fill Source...............................................................................................................................24
3.5.5 Mask ......................................................................................................................................24
3.6 STILLS...........................................................................................................................................24
3.6.1 Load Still.................................................................................................................................24
3.6.2 Save Still.................................................................................................................................25
3.6.3 Grab Still ................................................................................................................................25
3.6.4 Freeze.....................................................................................................................................25
3.7 USER MEMS..................................................................................................................................26
3.7.1 Load Memory.........................................................................................................................26
3.7.2 Save Memory .........................................................................................................................26
3.7.3 Load Clip ................................................................................................................................26
3.8 INPUTS .........................................................................................................................................26
3.8.1 Input 1-4 ................................................................................................................................27
3.8.2 Freeze.....................................................................................................................................27
3.8.3 Crosspoint ..............................................................................................................................27
3.9 OUTPUTS ......................................................................................................................................27
3.9.1 Outputs ..................................................................................................................................27
3.9.2 Audio......................................................................................................................................28
3.9.3 Tally Mode .............................................................................................................................28
3.9.4 Multiviewer............................................................................................................................29
3.10 SETUP ..........................................................................................................................................29
3.10.1 Standard.............................................................................................................................29
3.10.2 Menu Mode........................................................................................................................29
3.10.3 Menu Preference................................................................................................................29
3.10.4 Auto Save ...........................................................................................................................30
3.10.5 Factory Default...................................................................................................................30
3.10.6 Reset Names ......................................................................................................................30
3.10.7 Language............................................................................................................................30
3.10.8 Software.............................................................................................................................30
CHAPTER 4 APPLICATIONS.............................................................................................................31
4.1 CHROMAKEYER ..............................................................................................................................31
4.2 LOGO INSERTION ............................................................................................................................31
4.3 LOADING STILL IMAGES ....................................................................................................................32
4.4 LOADING THE CLIP FOR STINGER TRANSITION EFFECT.............................................................................33
4.5 IMPORTING THE CLIP FOR STINGER TRANSITION EFFECT FROM THE PC ......................................................33
CHAPTER 5: APPENDICES..................................................................................................................36
APPENDIX 1: TALLY OUTPUTS ......................................................................................................................36

4
APPENDIX 2: FIRMWARE UPGRADE ...............................................................................................................37
APPENDIX 3: FREQUENTLY-ASKED QUESTIONS ................................................................................................38
APPENDIX 4: DIMENSIONS ..........................................................................................................................39
APPENDIX 5: SPECIFICATIONS.......................................................................................................................40
SERVICE AND SUPPORT....................................................................................................................41
Disclaimer of Product & Services
The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try
to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some
information in this manual, from time to time, may not be correct or may be incomplete. This manual may contain typing
errors, omissions or incorrect information. Datavideo Technologies always recommend that you double check the
information in this document for accuracy before making any purchase decision or using the product. Datavideo
Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage caused by using the
information contained within this manual. Further advice on the content of this manual or on the product can be obtained
by contacting your local Datavideo Office or dealer.

5
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe and
reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do
not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the
cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit
should not be placed in a built-in installation unless proper ventilation is provided.
7. This product should only be operated from the type of power source indicated on the marking label of the
AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be
walked on, rolled over, or otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the
products plugged into the extension cord do not exceed the extension cord rating.
10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed 15
amperes.
11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch
dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill
liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself.
Opening or removing covers that are marked “Do Not Remove” may expose you to dangerous voltage
points or other risks, and will void your warranty. Refer all service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified service personnel under the following
conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions. Adjust only those
controls that are covered by the operating instructions in this manual; improper adjustment of other
controls may result in damage to the unit and may often require extensive work by a qualified
technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f. When the product exhibits a distinct change in performance, indicating a need for service.

6
Warranty
Standard Warranty
•Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of
purchase.
•The original purchase invoice or other documentary evidence should be supplied at the time of any
request for repair under warranty.
•Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered by this
warranty.
•All mail or transportation costs including insurance are at the expense of the owner.
•All other claims of any nature are not covered.
•Cables & batteries are not covered under warranty.
•Warranty only valid within the country or region of purchase.
•Your statutory rights are not affected.
Two Year Warranty
•
All Datavideo products purchased after 01-Oct.-2008 qualify for a free one year
extension to the standard Warranty, providing the product is registered with
Datavideo within 30 days of purchase. For information on how to register
please visit www.datavideo.com or contact your local Datavideo office or
authorized Distributors.
•
Certain parts with limited lifetime expectancy such as LCD Panels, DVD Drives, Hard Drives are only
covered for the first 10,000 hours, or 1 year (whichever comes first).
Any second year warranty claims must be made to your local Datavideo office or one of its authorized
Distributors before the extended warranty expires.
Disposal
For EU Customers only - WEEE Marking
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to
dispose of your waste equipment by handing it over to a designated collection point
for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where you can drop off your
waste equipment for recycling, please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
CE Marking is the symbol as shown on the left of this page. The letters "CE" are the
abbreviation of French phrase "Conformité Européene" which literally means
"European Conformity". The term initially used was "EC Mark" and it was officially
replaced by "CE Marking" in the Directive 93/68/EEC in 1993. "CE Marking" is now used
in all EU official documents.

7
Chapter 1 Introduction
The datavideo SE-650 is a small, cost-effective, HD digital video switcher with easy-to-use professional
features. It offers two HD SDI and two HDMI inputs. Output options include one user assignable HD
SDI, two HDMI outputs.
The SE-650 also features an audio mixer with microphone and unbalance RCA audio inputs; more
features include Chroma Keyer, Luma Keyer, PIP, Wipe Generator, Still stores and Tally.
1.1 Features
•4 video Input : HD-SDI x 2 + HDMI x 2
-Frame Sync on each input
•3 Video Outputs : HD-SDI x 1 + HDMI x 2
•Audio input : Stereo RCA (L/R) x 1 + Microphone x 2
•Audio Output : Stereo RCA (L/R) x 1 + Stereo headphone mini Jack x 1
•Audio Mixer : MIC x 2 + Stereo x 1 + internal Digital embedded x 1
•Flexible Mix/Effects Processor with
-1 Upstream Keyer, supporting Chroma Key & Linear/Luma Key
-1 Upstream PIP, supporting Chroma Key & Luma Key Modes as well as unkeyed mode
-Wipe Generator
32 Wipe Patterns, including Circle & Heart
Borders & Softness Control
-Wipe, Mix & Cut Transitions
-Full M/E Preview function
-Logo insertion
•Any Input (1-4) can be used as a Frame store (Stills Store)
•Assignable Outputs
Program (w/ DSK)
Clean Program (w/o DSK)
Clean Preview (w/o DSK)
Multiview
One of the input signals
•XPT (Cross Point Assignment)
•Tally Output

8
1.2 System Diagram

9
Chapter 2 Connections and Controls
2.1 Rear Panel
1
HDMI Video Input 1-2
7
TALLY Output Port
2
HD-SDI Video Input 3-4
8
MIC IN – CH1/CH2
3
HD-SDI Video Output 1
9
Audio Input – Stereo RCA (Left/Right)
4
HDMI Video Output 1-2
10
Audio Output – Stereo RCA (Left/Right)
5
Ethernet Port
11
Power Switch
6
USB F/W Upgrade Port
12
DC IN
1
HDMI Video Input 1-2
The SE-650 provides two HDMI video input channels for connecting
HDMI video sources.
2
HD-SDI Video Input 3-4
The SE-650 provides two HD-SDI video input channels for connecting
HD-SDI video sources.
3
HD-SDI Video Output 1
The SE-650 provides an HD-SDI video output channels which can be
connected to HD-SDI video display.
4
HDMI Video Output 1-2
The SE-650 provides two HDMI video output channels which can be
connected to HDMI video display. HDMI 1 is user assignable and
HDMI 2 outputs Multiview display.
5
Ethernet Port
Feature under development
1
4
5
6
7
8
9
10
12
2
3
11

10
6
USB F/W Upgrade Port
USB port for firmware upgrade. Please refer to the Firmware
Upgrade section for the procedure.
7
TALLY Output Port
Sends Red, and Green tally signals to each channel.
Red indicates On-Air, and Green indicates next camera source. Tally
output port can connect other Datavideo peripheral devices such as
ITC-100, ITC-200, AM-100 or other monitor models, allowing the
peripheral device to communicate with the SE-650 or send tally
signal to be displayed on the monitor.
8
MIC IN – CH1/CH2
Two Channels of unbalanced MIC input.
Left
Channel
Right
Channel
States
MIC1
MIC2
MIC 1(L) and MIC 2(R) are respectively
connected to left and right channels.
MIC1
Not
Connected
When MIC 1 is connected to the left
channel and MIC 2 is not connected to
the right channel, the right channel
switch will replicate MIC 1 signal onto
the right channel thus both channels are
MIC 1 input signals.
Not
Connected
MIC2
When no MIC signal is connected to the
left channel and only MIC 2 is connected
to the right channel, MIC 2 signal will
not be replicated onto the left channel
which will thus be grounded.
Not
Connected
Not
Connected
When no MIC is connected to the two
channels, the left channel switch will
ground the left channel to prevent noise
from being generated.
9
Audio Input – Stereo RCA (Left/Right)
Connects unbalanced analog audio source (stereo) for streaming and
recording.
10
Audio Output – Stereo RCA (Left/Right)
Unbalanced analog audio output (stereo) for monitoring the
selected audio input source.

11
11
Power Switch
Power switch ON/OFF
12
DC IN
DC in socket connects the supplied 12V / 19W PSU. The connection
can be secured by screwing the outer fastening ring of the DC In plug
to the socket.
2.2 Front Panel
Switcher Settings
Transition Methods
Menu browsing buttons
T-Bar (manual transition)
RESET button
CUT button
User Memory
AUTO transition button
Transition Effects Program / Preview Outputs
WIPE transition effect selection
Program row
TRANS BG – Background transition
Preview row
MIX Enable/Disable button
Volume Control
WIPE transition effect Enable/Disable
Volume adjustment sliders
PIP/Keyer
Headphone jack
Switcher
Settings
Transition
Effects
PIP/Keyer
Transition
Program/Preview
Volume Control

12
PIP Enable/Disable buttons
Audio meter
Keyer Enable/Disable buttons
Headphone volume control knob
Logo Enable/Disable button
Switcher Keyboard Descriptions
Menu browsing buttons
Press the MENU button to gain access to the menu;
use the up/down/left/right arrow buttons to browse
through the menu and press ENTER button to select an
option or MENU button again to exit.
Reset Button
Mode 1 -
When in Menu Select mode (left hand
column of the OSD menu), pressing the 'Reset' button
will reset all
current menu items to their factory
defaults.
Mode 2 - When in a Sub-Menu, pressing the 'Reset'
button will reset the current menu line only.
User Memory
User Memory buttons 1-3 allow the user to quickly
recall and load previously saved switcher settings with
a single button press. This includes PIP, Keyer and DSK
settings. The switcher loads settings saved to User
Memory 0 as default settings used at boot up. See the
User Memory section for more information.
Transition Effects
WIPE Transition Effect Selection
Each Wipe button consists of black and white colors.
The white represents the current Program image and
the black represents the WIPE-IN image. There are a
total of 2 WIPE presets offered on the SE-650; the
WIPE buttons allow the user to make a selection
directly from the control panel for the first 2 and
remaining 30 WIPE effects are selectable from the
menu (Start).
Pressing the REV button reverses the direction of the
WIPE.

13
TRANS BG – Background Transition
The TRANS BG button enables Background Transition
between Program / Preview. This feature is primarily
used in Chromakeyer effect. When enabled,
foreground and background will be switched together
during transition. The background will be locked when
the TRANS BG is disabeld, thus only the foreground is
switched during the transition and the background will
remain unchanged. If you would like to use the
switcher function, please enable the “TRANS BG”
function.
MIX Enable/Disable button
A MIX, also known as a dissolve, is a transition wherein
the Program video is replaced by the Preview video at
a smooth rate, and at the same time. Pressing the MIX
button will enable the MIX transition effect and
automatically disable the WIPE button. To activate the
MIX effect, simply press the AUTO button or move the
T-Bar.
WIPE Transition Effect Enable/Disable button
Pressing the WIPE button enables the WIPE transition
effect after which the WIPE transition effect can be
selected. To trigger the WIPE transition effect, simply
press the AUTO button or move the T-Bar.
Wipe transition effect selection, border and position
can be configured in the OSD menu (Start).
Note: When WIPE and MIX buttons are enabled at the
same time, the SE-650 enters the Clip Transition mode.
PIP/Keyer
PIP Enable/Disable buttons
Picture in Picture puts the selected Sub Video Source in
a window on the Main Program view, with control over
window size and placement. For PIP configuration,
please refer to the PIP section.
PIP PGM: Shows the configured PIP on multiview and
PGM outputs.
PIP PVW: Shows the configured PIP on PVW and
multiview outputs. Holding down this button also
allows selection of the PIP source
from the Preview
Source row. The selected source button will flash.
Note: You are also allowed to apply the chromakey
effect to the PIP window. Please refer to the PIP
section for chromakey configurations.

14
Keyer Enable/Disable buttons
KEYER PGM: Enables the key (Chroma / Luma / Linear)
on multiview and PGM output
KEYER PVW: Enables Keyer on
PVW and multiview
outputs. Press and hold this button until the Preview
Source row starts to flash and then select Keyer KEY or
FILL sourcesfrom the Preview Source row.
Please refer to the Keyer section for keyer
configurations.
Logo Enable/Disable button
The LOGO ON/OFF button enables the configured Logo
on PVW and PGM outputs. Please configure the logo
image source in the OSD. Refer to the Logo section for
configuration details.
Transition Methods
T-Bar (Manual Transition)
T-Bar is used to manually perform a transition. PVW
and PGM views can be transitioned at your preferred
speed. To include the transition effect, simply press the
WIPE or MIX button, after which the Transition Effect
will be trigger as you move the T-Bar.
CUT button
Pressing the Cut button performs i
mmediate manual
switch between PVW and PGM views
without any
transition effect.
AUTO button
Pressing the Auto button automatically transitions
PVW and PGM views according to the selected speed
and the configured transition effect.
Program / Preview Outputs

15
Program Source Row
Pressing the number buttons along the PROGRAM row selects a video source for the PGM view.
BKG button: Pressing the BKG button will switch the background to the Matte background or color
bars.
Still button: Pressing the STILL button will switch the Main Program view to a still picture, which can
be selected in the OSD menu.
Note: Pressing the STILL button repeatedly alternates the Main Program view between Still 1 and Still
2 pictures.
Preview Source Row
Pressing the number buttons along the PROGRAM row selects a video source for the PGM view.
BKG button: Pressing the BKG button will switch the background to the Matte background or color
bars.
Still button: Pressing the STILL button will switch the Main Program view to a still picture, which can
be selected in the OSD menu.
Note: Pressing the STILL button repeatedly switches the Main Program view between Still 1 and Still 2
pictures.
Volume Control
Volume Adjustment Sliders
Sliders to control audio levels for the Main audio mixer.
MIC 1: Unbalanced MIC IN
MIC 2: Unbalanced MIC IN
AUX: RCA audio input (analog)
Digital: HDMI or SDI audio input (digital)
Master: Main audio output
Headphone Jack
Headphones jack accepts a stereo mini jack plug for
stereo headphones. The headphone volume is
controlled by the Headphone volume control knob.

16
Audio Meters
LED style meters, which show the signal strength at the
Main Program Audio Output. The signal measured is
determined by the level set with the Master slider. The
LEDs turn red at +10 dB to indicate clipping distortion.
Audio
Volume (dBV)
-20 -10 -8 -4 0 4 8 10
LED Color
G
G
G
G
G
Y
Y
R
Range (dBV)
-20
-12
-11
-9.5
-8.5
-6.5
-5.5
-3
-2
1
2
5.5
6.5
8
9+
G: Green Y: Yellow R: Red
Headphone Volume Control Knob
Headphone volume control knob controls Headphone
level with the MIN representing the minimum volume
and MAX representing the maximum volume.

17
Chapter 3 OSD Menu
The switcher’s OSD menu allows the user to perform several configurations of image effects, such as
Picture-in-Picture, keyers, downstream keys, still pictures and etc. The user can also configure the I/O
by selecting the Inputs and Outputs options. In addition, in the setup option, the user is allowed to set
the menu color, size, position and language.
The OSD Menu offers the user basic and advanced modes. The basic mode is generally a condensed
version of the advanced menu mode. The following sub-sections will show you the various options
available in these two modes.
3.1 Start
Start
Transition
M/E
60
Type
MIX
Wipe Effects
Wipe
1
Soft
0%
Width
1%
Border
Luma
100%
Sat
80%
Hue
0
Position
X
0%
Y
0%
Matte
Luma
100%
Sat
80%
Hue
0
3.1.1 Transition
The Transition sub-option allows the user to set the MIX effect duration, in frames. If the M/E is set to
a value of 50 then the transition will take effect over a period of 50 frames or roughly 2 seconds.
When the AUTO button is pressed, the transition will take the current M/E value defined by the user
setting.
3.1.2 Type
The SE-650 provides three major types of transition effect, which are MIX, WIPE and Clip. Please note
in addition to selecting the transition effect on the OSD menu, you are also allowed to press the MIX
button, WIPE button or press MIX and WIPE buttons at the same time to enable the respective
transition effects.
•If MIX is selected, set the transition duration in the “Transition” sub-option.
•If WIPE is selected, set the relevant WIPE settings in the “WIPE Effects” sub-option.
•If Clip, also known as the Stinger Effect, is selected, please load the clip in the “User Mems”
sub-option.
3.1.3 Wipe Effects
This sub-option allows the user to select the Wipe Effect and configure the wipe’s border softness and
width.
•Wipe – Selection of a WIPE effect from a set of 32 WIPE transition effects.
•Soft – A low value results in a solid edge border and a high value gives a soft diffused border.
•Width – A low value results in a thin border and a high value gives a wide border.

18
3.1.4 Border
In this sub-option, the user will be allowed to fine-tune the border color by adjusting the Luma,
Saturation and Hue values.
3.1.5 Position
Position allows the user to adjust the center position of some wipes (e.g Circle & Elipse). Xrepresents
the horizontal position and Yis the vertical position.
Horizontal Position (X)
Positive value moves the wipe center to the right.
Negative value moves the wipe center to the left.
Zero value positions the wipe center at the screen center
Vertical Position (Y)
Positive value moves the wipe center up.
Negative value moves the wipe center down.
Zero value positions the wipe center at the screen center.
3.1.6 Matte
The user can configure the Matte by adjusting Luma, Saturation and Hue in this sub-option.
3.2 Keyer
Keyer of the SE-650 provides the user with the capability of image keying.
Advanced mode options
Keyer
Keyer
Chroma
Self
Priority
Top
Keyer Ctrl
Lift
0
%
Gain
1.0
Opac
100
%
Key Source
Input 1
Fill
Black
CK Setup
CK Auto
Hue
140
Luma
101%
K Range
160
K Fgnd
10%
K Bgnd
90%
Hi-Light
0%
Lo-Light
0%
Bg-Supp
OFF
Mask
Left
0%
Right
0%
Top
0%
Bot
0%
3.2.1 Keyer
There are three keying modes available: Linear, Luma, and Chroma.
Linear keying mode is usually chosen for sharp images. For non-sharp images, please select Luma
keying. Chroma keying mode allows you to remove the green or blue backdrop from the image.
After the keying mode is chosen, select Self if only one source is enabled for the keyer, which is Key
source. Select Split if two sources are enabled for the keyer, which are Key and Fill sources.
Priority sets the key image to either the top layer or bottom layer.
3.2.2 Keyer Control
“Keyer Control” adjusts lift, gain and opacity of the key image.

19
Lift adjusts the dark/black areas of the key image.
Gain adjusts the light/white areas of the key image.
Opac adjusts the transparency of the overall foreground key image.
3.2.3 Key Source
This sub-option allows the user to assign the key source; various options are listed below:
•Bars
•Matte – Set in Start/Matte
•Freeze
•Still 1
•Still 2
•Input 4
•Input 3
•Input 2
•Input 1
•Black
3.2.4 Fill Source
This sub-option allows the user to assign the fill source; various options are listed below:
•Bars
•Matte – Set in Start/Matte
•Freeze
•Still 1
•Still 2
•Input 4
•Input 3
•Input 2
•Input 1
•Black
3.2.5 CK Setup
In this sub-option, the user will be able to find all the parameters needed to perform chromakeying of
the green or blue backdrop.
CK Auto: This function automatically calculates the best Hue & Luma values for the current Keyer
source.
Hue: This parameter adjusts the color of the chroma key. A typical green screen value will be around
120. Blue screen value will be around 240.
Luma: This parameter adjusts the luma value of the chroma key
K Range (Key Range): Key Acceptance sets the range of hues or colors (0 – 360 degrees) that closely
match the background color to be keyed. The user can start with a value of 120 degrees and this value
can be fine-tuned up or down depending on the setup of the green or blue screen studio.

20
K Fgnd (Key Foreground): Key Foreground adjusts the performance of the chroma key in light or white
areas. Apply more Key Foreground if the light areas are becoming too transparent.
K Bgnd (Key Background): Key Background adjusts the performance of the chroma key in dark or
black areas. Apply more Key Background if the dark areas are becoming too transparent.
Hi-Light: Hi-light boosts the foreground key in high luminance area.
Lo-Light: Lo-light boosts the foreground key in low luminance area.
Bg-Supp: Background Suppress removes the Luma (Brightness) of the background from the final
image. Bg-Supp turns ON/OFF background suppression.
3.2.6 Mask
The Mask feature basically shrinks the camera image by removing the borders from the final image.
This feature allows the user to configure the Mask in chroma, luma or linear mode.
•Left – Left sets the left edge of the keyer mask.
•Right – Right sets the right edge of the keyer mask.
•Top – Top sets the top edge of the keyer mask.
•Bottom – Bottom sets the bottom edge of the keyer mask.
3.3 P-In-P
Picture-In-Picture (P-In-P) places a sub window on the PGM or PVW screens and allows you to
configure various parameters of the PIP window.
Advanced mode options
P-in-P
P-in-P Src
Input 2
Position
X
-31%
Y
-14%
Size
32%
Border
Luma
100%
Sat
80%
Hue
0
Border
Width
2%
Crop
Left
0%
Right
0%
Size
0%
Top
0%
Bot
0%
3.3.1 P-In-P Source
This sub-option allows the user to assign the P-In-P source; various options are listed below:
•Bars
•Matte – Set in Start/Matte
•Freeze
•Still 1
•Still 2
•Input 4
•Input 3
•Input 2
•Input 1
•Black