Datalogic DS2100A User manual

DS2100A
Laser Barcode Reader
Quick Reference Guide
The scanner is classified as a Class 2 laser
product according to EN 60825-1 regulations
and as a Class II laser product according to
CDRH regulations.
Disconnect the power supply when opening the
device during maintenance or installation to
avoid exposure to hazardous laser light.
There is a safety device which allows the laser to
be switched on only if the motor is rotating above
the threshold for its correct scanning speed.
The laser beam can be switched off through a
software command (see also the WinHost Help
On Line).
Figure A
Warning and Device Class Labels
1
2
3
4 8
7
6
5
Mounting Holes
Laser On LED
Good Read LED
External Trigger LED
Power On / Data TX LED
Warning and Device Class Labels
Accessory Mounting Holes
Laser Beam Output Window
For further details on product installation, see the
complete Installation Manual.
DS2100A can be configured through the WinHost
Windows-based software program available on the
installation CD-ROM.
For configuration it is necessary to create a cable
connecting the scanner to the PC as indicated in the
“How To Build A Simple Interface Test Cable” section of
this guide.
The laser diode used in this device is
classified as a class 3B laser product
according to EN 60825-1 regulations and as a
Class IIIb laser product according to CDRH
regulations. As it is not possible to apply a
classification label on the laser diode used in
this device, the following label is reproduced
below.
LASER LIGHT
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
MAX. OUTPUT RADIATION 35 mW
EMITTED WAVE LENGTH 630~680 nm
TO EN 60825-1 (2001)
Laser Diode Class Label
Any violation of the optic parts in particular
can cause radiation up to the maximum level
of the laser diode (35 mW at 630 to 680 nm).
POWER SUPPLY
- This product is intended to be installed by Qualified
Personnel only.
- All Models:
This accessory device is intended to be supplied by a UL
Listed or CSA Certified Power Unit with «Class 2» or LPS
power source which supplies power directly to the
scanner via the 25-pin connector.
CAUTION-CLASS 3B LASER LIGHT
WHEN OPEN AVOID EXPOSURE TO BEAM
This product conforms to the applicable
requirements of 21CFR1040 at the date
of manufacture.
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAX. OUTPUT RADIATION 1 mW
EMITTED WAVE LENGTH 630~680 nm
TO EN 60825-1:2001
R
CUS
218441
N2468
1
5
4
23
8
7
6

DS2100A QUICK GUIDE
2
Model Description:
DS2100A - X X X X
Optical Resolution
1 = Standard resolution
2 = High resolution
Communication Interface
2= RS232/RS485main + RS232 aux Optic Version
0 = Linear
1 = Raster R1
Performance
0 = Standard
4 = Testarossa ™
Reading Performance:
Version Reading Distance Max Code
Resolution
mm (mils)
Speed
scans/s
1XX0 40 mm (1.6 in) - 300 mm (11.8 in) on 0.50 mm (20 mils) codes 0.20 (8) 500 to 800
1XX4 50 mm (1.8 in) - 310 mm (11.8 in) on 0.50 mm (20 mils) codes 0.20 (8) 800 to 1000
2XX0 30 mm (1.2 in) - 90 mm (3.5 in) on 0.30 mm (12 mils) codes 0.15 (6) 500 to 800
2XX4 45 mm (1.8 in) - 100 mm (3.9 in) on 0.20 mm (8 mils) codes 0.12 (5) 800 to 1000
Technical Features:
ELECTRICAL FEATURES SOFTWARE FEATURES
Power Supply 10 –30 Vdc Readable Codes
Power Consumption Model XXX0: 3W
Model XXX4: 5W
Main Serial Interface Programmable:
RS232;
RS485 Full-Duplex/Half-
Duplex;
Auxiliary Interface RS232
*
*
*
*
*
*
*
EAN/UPC
(including Add-on 2 and Add-on 5)
Code 39
2/5 Interleaved
Code 128
EAN 128
Codabar
Code 93
Baudrates 150 to 115200
* = ACB readable
ISBT 128
Inputs
Pharmacode
External Trigger (optocoupled NPN or PNP) Headers and
Up to four header and four
Voltage max. 30 Vdc Terminators
terminator characters
Current Consumption 25 mA Operating Modes
On-Line, Automatic,
max.
Serial-On-Line, Test
Outputs ) Configuration Modes Through menus using:
OUT1, OUT2 (optocoupled) WinHost utility
Host Mode (commands from
V
CE max. 40 Vdc one of the serial ports)
Collector Current 40 mA continuous; Code Selection Up to six different codes
max. 130 mA pulsed during one reading phase
V
CE
Saturation 1V at 10 mA max. Decoding Safety Can enable multiple good
Power Dissipation 90 mW at 40 °C reads of the same code
max. (Ambient temp.) Special Functions ACB (Advanced Code Builder)
Motor Off
OPTICAL FEATURES
Light Source semiconductor laser diode Parameter Storage Non-volatile internal EEPROM
Wavelength In the range 630 to 680 nm ENVIRONMENTAL FEATURES
Safety Class Class 2 - EN 60825-1; CDRH Operating 0° to +40 °C (+32° to +104 °F)
Temperature
USER INTERFACE Storage -20° to +70 °C (-4° to +158 °F)
LED Indicators Laser ON, Good Read, Temperature
External Trigger, Humidity max 90% non condensing
Data TX / Power ON Vibration Resistance IEC 68-2-6 test FC 1.5 mm;
PHYSICAL FEATURES 10 to 55 Hz; 2 hours on each axis
Dimensions 68x83.6x34 mm
(2.7x3.29x1.3 in) Shock Resistance IEC 68-2-27 test EA 30 G;
Weight 330 g.
(11.64 oz) 11 ms; 3 shocks on each axis
Protection Class IP65

DS2100A QUICK GUIDE
3
Accessories:
Name Description Part Number
GFC-2100 90° Reading Device 93A201000
GFC-2000 75° Reading Device 93A201080
INT-30 (for C-Box 100) 20 mA Current Loop Interface Board 93A151022
C-BOX 100/200 Connection Box 93ACC1510,93ACC1520
C-BOX 300/310 Connection Box Profibus 93A301000, 93A301030
C-BOX 400/410 Connection Box DeviceNet 93A301010, 93A301040
MEP-542/543 Photocell Kit NPN/PNP 93ACC1727, 93ACC1728
Electrical Connections:
DS2100A is equipped with a cable terminated by a 25-pin female D-sub connector for connection to the power
supply and input/output signals. You can bring system cables directly to the 25-pin connector or you can connect
the scanner directly to one of the various C-Box models and bring system wiring to it (see the relative C-Box
Installation Manual).
CAUTION
Do not connect GND and SGND to different (external) ground references. GND and SGND
are internally connected through filtering circuitry which can be permanently damaged if
subjected to voltage drops over 0.8 Vdc.
The details of the connector pins are indicated in the following table:
25-pin D-sub female connector pinout
Pin Name Function
13 VS Power supply input voltage +
25 GND Power supply input voltage -
1 CHASSIS Chassis Ground
9 VS External Trigger supply voltage +
18 EXT TRIG+ External Trigger +
19 EXT TRIG- External Trigger -
8 OUT1 + Output 1 +
11 OUT2 + Output 2 +
12, 22 OUT REF Output reference
20 RXAUX Auxiliary RS232
21 TXAUX Auxiliary RS232
23 CTSAUX Auxiliary handshake RS232
24 RTSAUX Auxiliary handshake RS232
6, 10, 14,
15, 16, 17 NC Not Connected
25-pin female connector
Pin RS232 RS485
Full-Duplex RS485 Half-Duplex
2 TX232 TX485+ RTX485+
3 RX232 RX485+
4 RTS232 TX485- RTX485-
5 CTS232 RX485-
7 SGND SGND SGND

DS2100A QUICK GUIDE
4
Mechanical Installation:
9
4.2
7.8
20°
2.5
73
42
R40
4.2
90°
30
13.8
17.5
2.5
23
mm
4.2n°2
1 x 45° n° 2
23.3*
0.92
14.5
0.57
83.6
3.29
5
0.098
10.3
0.4
40
1.57
0.4
10.3
40
1.57
14.6
0.57
M 4 n° 4
1.3
34
mm
inch
68
2.68
46
1.81
DS2100
* The quote refers to the scan line
Input/Output Connections:
INPUT NPN INPUT NPN MEP-543
EXT TRIG+
18
19
+ 5V
DS2100A EXTERNAL TRIGGER
Signal
V
Vext 30 Vdc max.
EXT TRIG-
Input NPN command using external power
MEP-543 Connector
DS2100A
18
19
+ 5V
VS
9
25 GND
EXT TRIG+
EXT TRIG- 43
2 1
(brown)
(white)
(blue)
Input NPN command using MEP-543 Photocell
OUTPUT
EXTERNAL TRIGGER
DS2100A
Signal
18
19
+ 5V
VS
9
25 GND Ground
V
EXT TRIG+
EXT TRIG-
Input NPN command using DS2100A power
USER INTERFACE
+
8/11
12/22 OUT REF
DS2100A
Vext 40 Vdc max.
C
E
Output open collector connections
INPUT PNP
18
19
+ 5V
DS2100A EXTERNAL TRIGGER
V
Signal
Ground
EXT TRIG+
EXT TRIG-
Vext 30 Vdc max.
Input PNP command using external power
V
CE max = 40 Vdc
I
max = 40 mA continuous
EXTERNAL TRIGGER
DS2100A
18
19
+ 5V
VS
9
25 GND Ground
V
Signal
EXT TRIG+
EXT TRIG-
Input PNP command using DS2100A power
DS2100A

DS2100A QUICK GUIDE
5
Connectivity:
RS232 Main Interface Connections RS485 Main Interface Connections
RS232 Point-to-point layout RS485 Point-to-point layout
cMain Serial Interface (RS232) cMain Serial Interface (RS485 Full Duplex)
dAuxiliary Serial Interface (Local Echo) (RS232) dAuxiliary Serial Interface (Local Echo) (RS232)
eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode)
Pass-through layout Multiplexer layout
cMain Serial Interface (RS232) cMain Serial Interface (RS485 Half-Duplex)
dAuxiliary Serial Interface (RS232) dAuxiliary Serial Interface (Local Echo) (RS232)
eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode)
RS232 Master/slave layout RS485 Master/slave layout
cMain Serial Interface (Slaves RS232 only) cAuxiliary Serial Interface (RS232)
dAuxiliary Serial Interface (RS232) dMain Serial Interface (RS485 Half-Duplex)
eExternal Trigger (for On-Line Mode) eExternal Trigger
Host
DS2100
A
Terminal
Host
MX4000
Host
DS2100
A
DS2100
A
Host
DS2100
A
Slave
DS2100
A
Slave
DS2100
A
Maste
r
Host
DS2100
A
Slave
DS2100
A
Slave
DS2400
A
Maste
r
Host
DS2100
A
Terminal
Host
DS2100
A
Terminal

DS2100A QUICK GUIDE
6
Reading Diagrams:
DS2100A-1200 (Standard Resolution, 500 scans/s)
CONDITIONS
Optic Version = Linear
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Pitch angle = 0°
Skew angle = 15°
Tilt angle = 0°
*Code Reading Condition = Standard
* Parameter selectable in Winhost
2
1
0
1
5
4
3
2
3
4
5
(in)
120
100
80
60
40
20
0
20
40
60
80
100
120
(mm)
0 1 32 106(in) 45 7 89
0 20 40 60 80 100 120 140 160 180 200 220 240 260 (mm) 280
11
300
12
0.20 mm
(8 mils) ≥0.50 mm (20 mils)
0.30 mm
(12 mils)
0.35 mm
(14 mils)
DS2100A-1200
Reading Distance vs Scanning Speed
01
3
2 10
6
(in)
4
5
7
8
9
0 20 40 60 80 100 120 140 160 180 200 220 240 260 (mm)
0.20 mm
280
11
300
12
0.30 mm
0.35 mm
0.50 mm
Distanc
e
Code
Resolution
500 scans/s
800 scans/s

DS2100A QUICK GUIDE
7
DS2100A-2200 (High resolution, 500 scans/s)
CONDITIONS
Optic Version = Linear
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Pitch angle = 0°
Skew angle = 15°
Tilt angle = 0°
*Code Reading Condition = Standard
* Parameter selectable in Winhost
1
0
2
1
2
(in)
01 53(in) 24
010 20 30 40 50 60 70 80 90 100 110 120 130 (mm)
60
50
40
30
20
10
0
10
20
30
40
50
60
(mm)
0.15 mm
(6 mils)
0.20 mm
(8 mils)
≥0.30 mm
(12 mils)
DS2100A-2200
Reading Distance vs Scanning Speed
0 1 53(in) 24
0 10 20 30 40 50 60 70 80 90 100 110 120 130 (mm)
0.30 mm
0.20 mm
0.15 mm
500 scans/s
800 scans/s
Code
Resolution
Distance

DS2100A QUICK GUIDE
8
DS2100A-1204 Testarossa™ (Standard resolution, 1000 scan/s)
CONDITIONS
Optic Version = Linear
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Pitch angle = 0°
Skew angle = 15°
Tilt angle = 0°
*Code Resolution:
High - for 0.30 mm (12 mils)
codes and smaller
Standard - for 0.50 mm (20 mils)
codes and greater
*Code Reading Condition = Standard
* Parameter selectable in Winhost
2
1
0
1
5
4
3
2
3
4
5
(in)
0 1 32 106(in) 45 789
0 20 40 60 80 100 120 140 160 180 200 220 240 260 (mm)
120
100
80
60
40
20
0
20
40
60
80
100
120
(mm)
280
11
300
12
0.15 mm
(6 mils)
0.20 mm
(8 mils)
0.30 mm
(12 mils) ≥0.50 mm
(20 mils)
DS2100A-2204 Testarossa™ - (High Resolution, 1000 scans/s)
CONDITIONS
Optic Version = Linear
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Pitch angle = 0°
Skew angle = 15°
Tilt angle = 0°
*Code Resolution:
High - for 0.15 mm (6 mils) codes
and smaller
Standard - for 0.20 mm (8 mils)
codes
*Code Reading Condition = Standard
* Parameter selectable in Winhost
1
0
2
1
2
(in)
01 53(in) 24
010 20 30 40 50 60 70 80 90 100 110 120 130 (mm)
60
50
40
30
20
10
0
10
20
30
40
50
60
(mm)
0.12 mm
(5 mils)
0.15 mm
(6 mils)
≥0.20 mm
(
8 mils
)

DS2100A QUICK GUIDE
9
User Interface:
The following table contains the pinout for standard RS232 PC Host interface. For other user interface types
please refer to their own manual.
RS232 PC-side connections
1 5
96
9-pin male connector
13
2514
1
25-pin male connector
Pin Name Pin Name
2 RX 3 RX
3 TX 2 TX
5 GND 7 GND
7 RTS 4 RTS
8 CTS 5 CTS
How To Build A Simple Interface Test Cable:
The following wiring diagrams show a simple test cable including power, external (push-button) trigger and PC
RS232 COM port connections.
25-pin D-sub male
7
20
SGND
RXAUX
TXAUX
21
DS2100A
25
13
GND
VS
9-pin D-sub female
GND
TX
RX
PC
2
3
5
18
9
EXT TRIG+
VS
Power Supply
VS (10 – 30 Vdc)
Power GND
Trigger
EXT TRIG-
19
Test Cable for DS2100A

DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
DS2100A-XXXX Laser Scanner e tutti i suoi modelli
and all its models
et tous ses modèles
und seine modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
der nachstehend angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.
Basée sur la législation des Etates membres relative à la compatibilité électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit
entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas
de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022, August 1994 : L IMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF INFORMATION
TECHNOLOGY EQUIPMENT
(ITE)
EN 61000-6-2, April 1999 : E LECTROMAGNETIC COMPATIBILITY (EMC).
P
ART 6-2: G ENERIC S TANDARDS - I MMUNITY FOR INDUSTRIAL ENVIRONMENTS
Lippo di Calderara, 30/04/2004
Ruggero Cacioppo
Quality Assurance Supervisor
821000953 (Rev. C)