Dataprobe iPIO-16 User manual

IPIO quick start © 2018 Dataprobe Inc. V180802E
What’s Included
iPIO-xx Unit
Network Cable
Quick Start Guide
A/C Power Supply
Available Online at
dataprobe.com/support-ipio
Complete Product Manual
Device Management Utility
Latest Firmware
Software Developer Tools
Connections
1. Connect Network. iPIO supports 10/100 Ethernet using the cable supplied, or other suitable unshielded twisted pair (Cat
5) cabling. When power is connected to the iPIO, the green Activity LEDs on the network connector indicates when the
network connection is properly established.
2. Connect Inputs. (2 Connections per Channel)
Connect the inputs to the iPIO using the screw terminals.
Inputs can be either dry relay or switch contacts, or a +VDC
voltage (3 to 30 V), referenced to a common ground.
Screw terminals are removable for easy installation.
Terminals for each circuit are marked + and G. When
connecting dry relay contacts, the polarity is not significant.
3. Connect Relays. (3 Connections per Channel)
Relays are Form C. Connect to the Common (C),
Normally Closed (NC) and Normally Open (NO) as
marked. When the iPIO-8 relay is in the Open Condition,
the Common is connected to the Normally Open. In the
Closed state, the Common and Normally Closed are
connected.
4. Connect Power. Each unit is supplied with a n A/C
Power supply. Connect to suitable A/C source, then
power up the iPIO device. The iPIO-2 supports Power
over Ethernet (PoE). Consult the complete manual for more details.
.
Quick Start Guide
The iPIO is Factory set for Dry
Contact Input Only.
Prior to Connecting +VDC, Jumpers
must be configured.
See full manual or contact Dataprobe
Technical Support.
Relay Specifications
Rating (resistive)
0.5 A 120 VAC or
1 A 24 VDC
Max Carrying Current
2 A
Max Switching Power
60 AV, 24 W
Max Switching Voltage
120 VAC/60 VDC
Max Switching Current
1A
Life Expectancy
5 Million Operations Mech.
100K Oper. at rated load

Web Browser Access
Factory Default IP Address: 192.168.1.254
Factory Default Security Credentials:
Role
Username
Password
Administrator
admin
admin
To access the iPIO from the default IP Address, requires the
PC to be on the same local network (IP Address
192.168.1.nnn). If it is not, change the iPIO IP Address using
one of the methods on the following page.
After pointing the browser to the IP Address of the iPIO, enter
the Administrator Username and Password to access the
complete setup features. Enter the User credentials to access
only the power control. Once the user is validated, the Control
and Status is displayed.
Input and Output status is updated automatically. To control
any Output Relay, click on the Change link adjacent to the
Relay Status.
Changing the IP Address
1. Device Management Utility Obtain the Device
Management Utility (DMU) from Dataprobe’s website at
dataprobe.com/support-ipio.The DMU provides the easiest
means to find and configure your iPIO for use. It can discover
all the iPIOs on your network, display the current IP address of
each, and allow setting of any valid IP address.
Note: The IP address can only be set within the first two
minutes of powering up the iPIO. The Setup Utility will only
work with iPIOs on the same physical subnets as the PC.
The iPIO Setup Utility can also be used to return an iPIO to its
Factory Default condition. This can be used to recover an iPIO
with a lost password. Highlight an iPIO from the display and click
Factory Defaults. This must also be done within the first two
minutes of powering up the iPIO.
Complete instructions for the DMU are provided with the
download, and in the full iPIO Manual.
2. Web Page Setup From the home page, click on Setup, then
Network. Enter the new IP Address, Subnet Mask and Gateway,
then click Save. Click the Reboot button (or press the reset
button next to the power outlet LED) to restart the iPIO with the
new settings.
3. DHCP From the Home page, click on Setup, then Network.
Change the IP Mode from Static to DHCP. Click Save, then
Reboot. The iPIO will obtain its network settings from the server.
Check the server, or use the Device Management Utility to obtain
the new settings.