Datatek DT-6XXX User manual

I
IP P- -B B2 2A AP PR RT T
BISYNC TO ASCII PRINTER
APPLICATION
USER'S MANUAL
FOR
DT-6XXX
EMBEDDED NETWORK PROCESSORS
RELEASE.VERSION 9.0
ISSUE 2
379 Campus Drive, Suite 100
Somerset, NJ 08873
fax: [phone]
phone: [phone]
email: [e-mail]
http://www.datatekcorp.com

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 2
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS..............................................................4
1INTRODUCTION...........................................................................................5
1.1 IP-B2APRT APPLICATION (INTEGRATED CONFIGURATION) ................................5
1.2 IP-B2APRT APPLICATION (NON-BNS/DATAKIT CONFIGURATION) .....................6
1.3 IP-B2APRT APPLICATION WITH THE IP-SPOOL APPLICATION ..........................7
2IP-B2APRT APPLICATION CONFIGURATION ...........................................8
2.1 DT-6XXX PLATFORM CONFIGURATION ..............................................................8
2.2 IP-B2APRT APPLICATION CONFIGURATION .......................................................8
2.3 SAMPLE CONFIGURATION ..................................................................................9
2.3.1 UMI Configuration.................................................................................................. 10
2.3.2 SYNC8 Configuration ............................................................................................ 11
2.3.3 DT-6XXX Platform and IP-B2APRT Application Configuration........................ 11
2.3.4 DT-4000 Configuration .......................................................................................... 12
2.3.5 IP-B2APRT Application Configuration................................................................. 13
3APPLICATION COMMANDS......................................................................14
3.1 INPUT CONVENTIONS .......................................................................................14
3.2 LOGIN.............................................................................................................14
3.3 LOGOUT..........................................................................................................15
3.4 CHANGE PASSWORD - CHGPASS......................................................................15
3.5 APPLICATION CONSOLE USER HELP - HELP......................................................15
3.6 VERSION - VER................................................................................................15
3.7 LABEL ............................................................................................................15
3.8 BANNER MESSAGE - BANNER ..........................................................................15
3.9 APPLICATION COMMENTS - COMMENT ..............................................................16
3.10 OA&M SESSION TIMER CONFIGURATION - TIMEOUT..........................................16
3.11 CONFIGURING BISYNC HOST INTERFACE PARAMETERS - HOST..........................16
3.12 CONFIGURING ASCII PRINTER INTERFACE PARAMETERS - PRT .........................16
3.13 REMOVE CONNECTIONS FROM SERVICE - RM....................................................17
3.14 RESTORE CONNECTIONS TO SERVICE - RS........................................................17
3.15 VERIFY CONFIGURATION - VFY .........................................................................17
3.16 DISPLAY CURRENT CONNECTIONS - DCONN......................................................17

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 3
3.17 DISPLAY LOG - DLOG.......................................................................................18
3.18 CLEAR LOG – CLEAR LOG................................................................................18
3.19 DISPLAY MEASUREMENTS - DMEAS ..................................................................18
3.20 CLEAR MEASUREMENTS - CLR .........................................................................18
4APPLICATION SOFTWARE INSTALLATION & UPGRADE .....................18
5HARDWARE WARRANTY..........................................................................19
6END-USER LICENSE AGREEMENT FOR SOFTWARE............................19
6.1 SOFTWARE LICENSE........................................................................................19
6.2 INTELLECTUAL PROPERTY RIGHTS...................................................................19
6.3 SOFTWARE SUPPORT ......................................................................................20
6.4 EXPORT RESTRICTIONS ...................................................................................20
6.5 LIMITED WARRANTY ........................................................................................20
6.6 NO OTHER WARRANTIES .................................................................................20
6.7 SPECIAL PROVISIONS ......................................................................................21
7LIMITATION OF LIABILITY........................................................................21

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 4
IMPORTANT SAFETY INSTRUCTIONS
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
DT-6XXX product.
When installing, operating, or maintaining this equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
! Read and understand all instructions.
! Follow all warnings and instructions marked on this product.
! For information on proper mounting instructions, consult the User’s Manual provided with this product.
! The telecommunications interface should not leave the building premises unless connected to telecommunication
devices providing primary and secondary protection.
! This product should only be operated from the type of power source indicated in the User’s Manual.
! This unit is intended to be powered from either –48 V DC or AC voltage sources. See User’s Manual before
connecting to the power source.
! The –48 V DC input terminals are only provided for installations in Restricted Access Areas locations.
! Do not use this product near water, for example, in a wet basement.
! Never touch uninsulated wiring or terminals carrying direct current or leave this wiring exposed. Protect and tape
wiring and terminals to avoid risk of fire, electric shock, and injury to service personnel.
! To reduce the risk of electrical shock, do not disassemble this product. Service should be performed by trained
personnel only. Opening or removing covers and/or circuit boards may expose you to dangerous voltages or other
risks. Incorrect re-assembly can cause electric shock when the unit is subsequently used.
! For a unit intended to be powered from –48 V DC voltage sources, read and understand the following:
• This equipment must be provided with a readily accessible disconnect device as part of the building installation.
• Ensure that there is no exposed wire when the input power cables are connected to the unit.
• Installation must include an independent frame ground drop to building ground. Refer to User’s Manual.
This symbol is marked on the DT-6XXX, adjacent to the ground
(earth) area for the connection of the ground (earth) conductor
! This Equipment is to be Installed Only in Restricted Access Areas on Business and Customer Premises Applications
in Accordance with Articles 110-16, 110-17, and 110-18 of the National Electrical Code, ANSI/NFPA No. 70. Other
Installations Exempt from the Enforcement of the National Electrical Code May Be Engineered According to the
Accepted Practices of the Local Telecommunications Utility.
! For a unit used with an AC Wall Plug-In Unit, read and understand the following:
• Contact Datatek Applications, Inc or its authorized resellers for specifications for procuring an AC power unit.
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
• Do not staple or otherwise attach the power supply cord to the building surfaces.
• Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
• The socket outlet shall be installed near the equipment and shall be readily accessible.
• The Wall Plug-In unit may be equipped with a three-wire grounding type plug, a plug having a third (grounding)
pin. This plug is intended to fit only into a grounding type power outlet. Do not defeat the safety purpose of the
grounding type plug.
• Do not allow anything to rest on the power cord. Do not locate this product where the cord may be abused by
persons walking on it.
• Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a) When the powers supply cord or plug is damaged or frayed.
b) If liquid has been spilled into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions because improper adjustment of other controls may result in
damage and will often require extensive work by qualified technician to restore the product to normal
operation.
e) If the product has been dropped or the cabinet has been damaged.
f) If the product exhibits a distinct change in performance.
Save These Instructions
!

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 5
1 INTRODUCTION
The BiSync to ASCII printer application (IP-B2APRT) is a companion application to the TN-3270
Server application of the DT-6XXX. This Application type is designed to replace the A2B DKAP
application in either an integrated (Both BNS/Datakitand IP networks together), or a non-BNS
environment (IP network only).
1.1 IP-B2APRT APPLICATION (INTEGRATED CONFIGURATION)
The following diagram depicts a configuration of the IP-B2APRT application in an integrated
environment. It replaces the A2B DKAP module.
Node
B
H
I
M
U
M
I
IP IP
IP
BiSync Host
ASCII Printers
BiSync
DT-6XXX
DT-4XXX
135.19.22.6
135.19.22.4
135.19.22.8 IP
Network
IP-B2APRT Application Installed
In the above diagram the IP-B2APRT application addresses both the ASCII printer and the BNS
circuit group for each particular printer. The operation is similar to the BNS A2B DKAP with
regard to the printer functionality.
The Universal Mediation Interface1(UMI) module provides the protocol mediation between the
BNS network, and the IP network. A hunt group set up for each ASCII printer would be predefined
to address the BHI address group for that printer.
Datakit is a registered trademark of LucentTechnologies, Inc.
1The UMI allows both synchronous and asynchronous endpoints connected to a BNS network to access
endpoints on an IP network. Similarly, endpoints on an IP network can access both synchronous and
asynchronous endpoints on a BNS network.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06
Datatek Applications Inc. 6
1.2 IP-B2APRT APPLICATION (NON-BNS/DATAKIT CONFIGURATION)
The IP-B2APRT application may also be used in circumstances where there is no BNS network.
ASCII Printers
IP
Network
BiSync Host
DT-4XXX DT-4XXX
DT-6XXX IP-B2APRT Application
IP-BHI Application
IP
IPIP
BiSync
In the above diagram, the DT-6XXX is actually executing one or more instances2of two distinct
applications3.
1) The first is the IP-B2APRT application, the same application as in the integrated network
case, and the subject of this manual.
2) The second application is the BiSync Host Interface (BHI) application. The BHI application
interfaces with a BiSync host and performs Cluster Controller emulation for a multi-point host
line.
2An application instance can be described as a unit of configuration parameters as a specific DT-6XXX
application defines them. In other words, each instance of an application is a completely separate process
where all aspects of the operation of the application are performed entirely within that process.
3The DT-6XXX Platform may support up to 5 simultaneous application types.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06
Datatek Applications Inc. 7
1.3 IP-B2APRT APPLICATION WITH THE IP-SPOOL APPLICATION
The following diagram is another derivative of the one shown in section 1.1. In addition to the IP-
B2APRT application installed in a DT-6XXX, the IP-SPOOL application is installed also. The IP-
SPOOL application allows the sharing of printers. Instead of the BiSync host and TN3270 clients
each having dedicated printers which are probably underutilized and require maintenance, an
RFC 1179 capable printer can be shared.
The BiSync host and TN3270 clients still interface to the IP-B2APRT application in the DT-6XXX.
Now the IP-B2APRT application itself has connections to virtual printers instead of individual,
dedicated ASCII printers. Each virtual printer is an instance of the IP-SPOOL application Other
users in the network, in this case, network elements which normally send ASCII ROP output to
dedicated printers, now instead have connections to other virtual printers, i.e. other instances of
the same IP-SPOOL application. However, all share the same physical RFC1179 compatible
printer whose queue is managed by the IP-SPOOL application. More detail about the IP-SPOOL
application can be found in the DT-6XXX IP-SPOOL Application User’s Manual available on the
Datatek Applications, Inc. WEB site.
BiSync Host
Node
B
H
I
M
U
M
I
DT-6XXX
RFC1179 Printer
TN3270 Clients
IP
Network
with
IP-B2APRT Application
IP-Spool Application
NE NE
DT-4XXX Serial ROP
Interfaces.
10/100BaseT
10/100BaseT

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06
Datatek Applications Inc. 8
2 IP-B2APRT APPLICATION CONFIGURATION
2.1 DT-6XXX PLATFORM CONFIGURATION
Before proceeding with the configuration of the IP-B2APRT Application, make sure that the DT-
6XXX Platform has been properly configured and the IP-B2APRT Application is installed on the
DT-6XXX Platform. The steps necessary for this are outlined below and are stated in greater
detail in the DT-6XXX Platform User's Manual.
Platform Configuration:
This command sequence is required for the initial configuration of the DT-6XXX.
Application Installation:
This action requires that a host acting, as an ftp server is present on a network that is accessible
by the DT-6XXX install command.
Assignment of an Application to an Instance:
The number and type of application must be configured as a system parameter.
2.2 IP-B2APRT APPLICATION CONFIGURATION
Once the DT-6XXX Platform configuration is complete, instances of the IP-B2APRT Application
along with circuits for the ASCII Printer and BiSync Host may be configured.
First, the configuration of the IP-B2APRT application takes place through the application's
Console port. This port is accessed by making a Telnet call to the IP Address of the DT-6XXX
that includes the TCP port number of the IP-B2APRT application instance. The TCP port
number of the IP-B2APRT application instance is calculated using the following equation:
10000 + ( the application instance # in the DT-6XXX )
Note: The Application Console is different from the DT-6XXX Platform Console
Next, each instance of the IP-B2APRT application supports a single ASCII printer. Therefore,
one TCP session exists for each ASCII printer connection. This TCP connection is originated by
the IP-B2APRT application where the IP address and port number of the ASCII printer port is
configured through the IP-B2APRT application console.
Finally, one TCP session exists for the BHI connection to the BiSync host for a particular printer.
The TCP connection is originated by the IP-B2APRT application. The IP address and port
number of the BHI is a configuration option available through the IP-B2APRT Application
Console.
An example of how these circuits are used follows:
1. The IP-B2APRT application would have the IP address and TCP port number of the ASCII
printer configured. In addition, the BHI IP address and TCP port number configuration is also
entered.
2. Once restored to service, the IP-B2APRT establishes a TCP connection to both the ASCII
printer, and the BHI. By definition, the ASCII printer connection is asynchronous telnet, and
the BHI connection contains frame based (i.e. Synchronous) data.
3. The host may now print on the ASCII printer by using the BiSync printer definition on the
BiSync line.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06
Datatek Applications Inc. 9
2.3 SAMPLE CONFIGURATION
The following network diagram depicts a generic IP-B2APRT configuration. Several network
components require configuration. The administrator may need to configure one or more of the
following network elements.
1. UMI
2. SYNC8 (BHIM) Module
3. DT-6XXX platform
4. DT-4XXX (DT-4000)
5. IP-B2APRT application
6. TN-3270 application
7. ASCII Printer
8. BiSync Host
The following sections describe sample configurations for a subset of the items listed above and
are based on the diagram below. Configuration of BiSync Host and ASCII Printer is beyond the
scope of this document. Configuration of the TN-3270 application is described in detail in the TN-
3270 User's Manual. However, knowledge of the BiSync Host's configuration is required to
properly configure the BNS SYNC8 module.
Node
B
H
I
M
U
M
I
IP IP
IP
BiSync Host
ASCII Printers
BiSync
DT-6XXX
DT-4XXX
135.19.22.6
135.19.22.4
135.19.22.8 IP
Network
TN3270 Client
IP-B2APRT and TN-3270
Applications Installed

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 10
2.3.1 UMI CONFIGURATION
The overall configuration process for the UMI can be divided into two phases:
1. Base Configuration: setting up the UMI for IP connectivity and console security
2. Operational Configuration: setting up the UMI and BNS node to enable users to make calls
between the BNS and IP networks
2.3.1.1 BASE CONFIGURATION
The following console output reflects the output of the UMI verify command (part of UMI Module
command set). The results displayed below describe a UMI Base Configuration consistent with
the configuration needs of the previous network diagram. For a more detailed description of how
to configure the UMI, refer to the UMI User's Manual.
<UMI> verify vport 33
Virtual Ports 33 - 33 :
Type ==> TCP Port 12000 w/Call Listen.
Service State ==> In Service.
Protocol ==> Synchronous.
2.3.1.2 OPERATIONAL CONFIGURATION
The following console output reflects the output of the UMI verify command (part of UMI Node
command set). The results displayed below describe a UMI Operational Configuration consistent
with the configuration needs of the previous network diagram. For a more detailed description of
how to configure the UMI, refer to the UMI User's Manual.
CC0> vfy sam m p 17 2 1
MODULE ADDRESS: 17
MODULE TYPE: sam504 NCHLS: 512
SERVICE STATE: in SECS BEFORE DISCONNECT: 50
TRUNK TYPE: t1 LINE SPEED: 1.544M
TOTAL BOARDS: 16
DOWNLOAD SERVER: controller
VERSION: standard
COMMENT: UMI
BOARD SERVICE SOFTWARE
ADDR STATE VERSION
2in standard
DEV NWK ATT ATT
PORT TYPE FC FC XANY BAUD CHAR ACT PARITY SRVC BILL VDM GROUP
1 term N/A N/A N/A 9600 N/A N/A N/A in off N/A tn6XXX
CALL NODE BLD CABLE STOP CNST
PORT HOLD RBAUD ECHO NRZI PAP OUT TYPE BITS BITS PROTO CODE CARR
1 N/A N/A N/A no no 254 dce N/A N/A bisync ebcdic no
PORT EPN CUG PROFILE BFLUSH FRMFILL
1 N/A N/A
PORT PDD
1 bscprt
PORT COMMENT

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 11
1 DT-6XXX <--> UMI B2APRT
2.3.2 SYNC8 CONFIGURATION
The following console output reflects the output of the SYNC8 verify command. The results
displayed below describe a bsc3270 configuration consistent with the configuration needs of the
previous network diagram. For a more detailed description of how to configure the SYNC8
Module, refer to the BNS-2000 SYNC8 Module Reference Guide.
Note: knowledge of the BiSync Host's configuration is required to properly configure the BNS
SYNC8 module
CC0> vfy bsc terminal 30 2 2 4
MODULE ADDRESS: 30
MODULE TYPE: bsc3270 NCHLS: 100
SERVICE STATE: in
DOWNLOAD SERVER: controller
VERSION: standard
HOST MSG CODE PORT BAUD
PORT CHNLS TYPE TYPE CHNG SET DUPLEX RATE SRVC
2 7 host vtam no ebcdic full 9600 in
PORT COMMENT
2 to bsc printer
PORT CU SRVC
2 2 in
TERM SCRN RECV LOGOFF LOGOFF FWD
PORT CU TERM TYPE SIZE GRP METHOD SEQ ID ACK SRVC
2 2 4 basic/ro N/A bscprt none N/A N/A in
BKPL
PORT CU TERM CHNL
2 2 4 16
2.3.3 DT-6XXX PLATFORM AND IP-B2APRT APPLICATION CONFIGURATION
The DT-6XXX software is composed of two components. One component, called the Platform,
exists to support all applications. The second component is comprised of the individual
application(s).
The Platform provides Operating System functions, selected interfaces, protocol stacks, SNMP
functions, and system OA&M while each application uses the services of the resident Platform.
2.3.3.1 DT-6XXX PLATFORM CONFIGURATION
The following console output reflects the output of the DT-6XXX vfymod and vfycfg commands.
The results displayed below describe a DT-6XXX platform configuration consistent with the
configuration needs of the previous network diagram. For a more detailed description of how to
configure the DT-6XXX platform, refer to the DT-6XXX User's Manual.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 12
<DT-6XXX> vfy mod
ipaddr: 135.19.22.6
submask: 255.255.255.0
gateway: 135.19.22.1
mac addr: 0.96.29.2.55.219
serial #: 0.0.6.239.61.162
build #: 13.1
rtu #: 5
built on: Tue May 29 11:46:19 EDT 2001
booted: 766 hour 17' ago
<DT-6XXX> app 1 type=b2aprt
<DT-6XXX> vfycfg
1 type=b2aprt
2.3.4 DT-4000 CONFIGURATION
The following console output reflects the output of the DT-4000 vfymod and vfyport commands.
The results displayed below describe a DT-4000 configuration consistent with the configuration
needs of the previous network diagram. For a more detailed description of how to configure the
DT-4000, refer to the DT-4000 User's Manual.
<DT-4000> vfy mod
Current Module Level Configuration:
Serial Number ==> 0.0.5.138.152.38
Service State ==> In Service.
Local MAC Address ==> 0.96.29.2.55.8
Local IP Address ==> 135.19.22.4
Subnet Mask ==> 255.255.255.0
Gateway IP Address ==> 135.19.22.1
<DT-4000> vfy p 1
Current Configuration for Port 1:
Type ==> TCP Port 50001 w/Call Listen.
Service State ==> In Service.
Protocol ==> Asynchronous.
DXE ==> DCE.
Baud Rate ==> 9600 bps.
Line Encoding ==> NRZ.
Constant Carrier ==> Enabled.
Permanently Active ==> Enabled.
Number of Data Bits ==> 8 data bits per character.
Parity ==> None.
Number of Stop Bits ==> 1.
Attention Sequence ==> None.
Net->User Flow Control ==> None.
User->Net Flow Control ==> None.
NULL after CR Operation ==> Transparent.
Comment ==> "printer port"

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 13
2.3.5 IP-B2APRT APPLICATION CONFIGURATION
The following console output reflects the output of the B2APRT vfy command. This output
reflects the commands necessary to configure the B2APRT application so that it is consistent with
the configuration needs of the previous network diagram.
<B2APRT> prt dest=135.19.22.4 dport=50001
<B2APRT> host dest=135.19.22.8 dport=12000
<B2APRT> vfy
M Verify BiSync to ASCII Printer Instance Configuration
Local IP Address: 192.168.8.250, Instance Number: 1
ASCII Printer Interface: 135.19.22.4 Port 50001 - in service.
BiSync Host Interface: 135.19.22.8 Port 12000 - in service.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 14
3 APPLICATION COMMANDS
The DT-6XXX software is composed of two components. One component, called the Platform,
exists to support all applications. The second component is comprised of the individual
application(s).
The Platform provides Operating System functions, selected interfaces, protocol stacks, SNMP
functions, and system OA&M while each application uses the services of the resident Platform.
3.1 INPUT CONVENTIONS
All parameters may be given on the command line. Parameters of the form name=<value> may
be given in any order.
For several complex commands, listed below, missing parameters, or corrections of errors in
given parameters, of the form name=<value> are collected by prompting the console user. The
user responds to a prompt for the name by typing the required <value> followed by newline.
Defaults are supplied in some cases, so the user need only enter newline.
! Commands may be entered in upper or lower case.
! Parameters of the form name=value may use upper or lower case for name.
! Default values, if any, are shown in parenthesis as part of the prompt.
! Case is preserved for values.
! When a password is being requested by a prompt, input is not echoed.
Backspace erases one character and @deletes the current line of input. Most commands are
killed by del key.
3.2 LOGIN
Syntax: login passwd=<password>
or
Prompted Mode:
Syntax: login
password ? PASSWD=
The login command is used to allow access to the other commands. The legal characters for
passwords are the upper and lower case letters, numbers, and the following special characters:
~ ! @ # $ % ^ & * ( ) _ + { } | : < > ? ` - = [ ] \ ; ‘ , . /
Note that when inputting a password, all of these special characters are allowed. Double quote is
not allowed, nor is equal sign ‘=”allowed as the first character of a password in prompted mode.
Passwords are case sensitive.
The passwd parameter is not echo suppressed. However, if the passwd parameter is not
provided in the command line, the console prompts for a password (i.e. prompted mode); the
response is echo-suppressed in this case.
If the password is valid, the user is placed in the logged in mode. Once the console user is logged
in, the rest of the commands are accessible. The login command is not accessible if the user is
already logged in.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 15
3.3 LOGOUT
Syntax: logout
The logout command is only allowed if the console user is logged in. It uses no arguments. It will
set the console to the logged out mode. The console may also be logged out by typing exit or
ctrl-D.
3.4 CHANGE PASSWORD - CHGPASS
Syntax: chgpass PASSWD=<old> NEWPASS=<new> CONFIRM=<new>
The chgpass command is used to change a user password on a particular application type. The
command is only allowed if the user is logged in.
All three parameters can be given on the same line as the command. None of those entries are
echo-suppressed. However, if parameters are omitted from the command line, the console will
prompt for them, and the responses will be echo-suppressed.
If the current password is valid, and the two entries for the new password match, the password is
changed to the new value.
3.5 APPLICATION CONSOLE USER HELP - HELP
Syntax: help | ? [command]
The help command is always visible. The help command displays the currently allowed
commands for the mode that the unit is currently entered.
3.6 VERSION - VER
Syntax: ver
The version command is only visible when the application is logged in. The command has no
arguments. It displays the current software and database revisions of the application.
3.7 LABEL
Syntax: label [“label string”) | none]
If the command is issued without arguments, the current configuration is displayed. When issued
with an argument of "none", the label becomes a NULL label. Otherwise, a label up to 32
characters is allowed when enclosed in double quotes. (The double quotes are not counted as
part of the 32 characters). The label may be a mixture of alpha characters and digits. It is case
sensitive.
3.8 BANNER MESSAGE - BANNER
Syntax: banner [ L<#>=”System Banner Line <#>” ]
The banner command is only visible when the application is logged in. The command is used to
configure a system message banner that is displayed to the administrators upon connection.
There are currently eight (8) lines of banner. Each line may be configured independently of each
other with its own tag (i.e. L1, L2, …, L8). Each banner line may contain a maximum of 60
characters of text including spaces. The banner lines are visible on a verify command. The use

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 16
of this command is not required if no banner is desired. The banner may be cleared by using the
banner command with the parameter default. This will delete all banner lines.
3.9 APPLICATION COMMENTS - COMMENT
Syntax: comment [ L1=”comment”]
[ L2=”comment”]
[ L3=”comment”]
The comment command allows a user to add user information to the application instance. The
information is displayed during a verify command. Up to three lines of information may be
provided. Each line may be up to 64 characters in length, may include spaces, and is double
quoted. Each line may be changed individually. Comments may be cleared by setting the line
value to a null comment (i.e. “”).
3.10 OA&M SESSION TIMER CONFIGURATION - TIMEOUT
Syntax: timeout [ OFF | <Number of Seconds> ]
The timeout command configures the session timer. When configured, the session timer will
disconnect a user from the OA&M telnet port for this IP-SPOOL instance. No other instances on
the DT-6XXX are affected since each has its own OA&M connection. The default value for
timeout is OFF (Timeout disabled), and the range of seconds is 15-255.
3.11 CONFIGURING BISYNC HOST INTERFACE PARAMETERS - HOST
Syntax: HOST [dest=<BHI IP Address>][dport=<BHI TCP Port>]
The HOST command is only visible when the application is logged in. The command is used to
configure the parameters needed for connections to a BiSync Host interface application. There is
exactly one such connection.
When the IP-B2APRT application makes an originating connection to the BHI for a BiSync printer,
the dest configuration would specify the IP address and the dport is the hunt group TCP port for
the BHIM.
3.12 CONFIGURING ASCII PRINTER INTERFACE PARAMETERS - PRT
Syntax: PRT [dest=<ASCII Printer IP Address>][dport=<ASCII
Printer TCP Port>]
The PRT command is only visible when the application is logged in. The command is used to
configure the parameters needed for connections to an ASCII Printer. There is exactly one such
connection. The ASCII printer may be directly connected to a DT-4000, or SAM/DT-2020
combination. In addition, the ASCII printer may reside on an asynchronous port of a BNS
network. These connections would require a UMI module.
When the IP-B2APRT application makes an originating connection to the ASCII printer port, the
dest configuration would specify the IP address and the dport is the hunt group TCP port for the
DT-4000.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 17
The IP-B2APRT application may also be used with the IP-SPOOL application which enables the
sharing of one physical RFC 1179 compatible printer among many devices. Instead of to physical
printer, the PRT command points to a “virtual” printer of the IP-SPOOL application. The IP-
SPOOL application defines the actual physical, but now shared printer. For the PRT command,
dest is the IP address of the DT-6XXX on which the IP-SPOOL application is installed and dport
is the TCP port which is equal to 30000+ (instance# - 1)*200. where instance# is the number of
the instance, i.e. of the virtual printer on the IP-SPOOL application on the target DT-6XXX.
3.13 REMOVE CONNECTIONS FROM SERVICE - RM
Syntax: rm <host | prt>
Should a situation occur where the TCP connections to either the Host or the ASCII printer needs
to be taken down or altered, the connection should first be removed from service. That is the
function of the remove command.
The rm (remove)command requires one argument. This argument is either host or prt. When
the argument is host, the TCP connection to the BHI is taken down. When the argument is prt,
the TCP connection to the ASCII printer interface is taken down.
3.14 RESTORE CONNECTIONS TO SERVICE - RS
Syntax: rs <host | prt>
In order for any connectivity between the BHI Host, and the ASCII printer to occur, two TCP
connections are required. These are configured using the bsc and asc for the host and printer
respectively. After the addressing is configured, each connection needs to be brought into
service. That is the function of the restore command.
The rs (restore)command requires one argument. This argument is either host or prt. When the
argument is host, the TCP connection to the BHI is established. When the argument is prt, the
TCP connection to the ASCII printer interface is established.
3.15 VERIFY CONFIGURATION - VFY
Syntax: vfy
The vfy command is only visible when the application is logged in. The command is used to
display the configured options on the IP-B2APRT application. An example of the output of the vfy
command is shown previously on page 11.
3.16 DISPLAY CURRENT CONNECTIONS - DCONN
Syntax: dconn
The dconn command is used to display all of the current TCP connections on the IP-B2APRT
application. The command will issue a report that shows the connection peer for each active
connection.

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 18
3.17 DISPLAY LOG - DLOG
Syntax: dlog
The dlog command is used to display all entries in the log file.
An exclamation point (!) that precedes a log entry denotes new entries. A double asterisk
(**) that precedes a log entry denotes duplicate entries.
3.18 CLEAR LOG – CLEAR LOG
Syntax: clear log
The log file can be cleared with the command, clear log.
3.19 DISPLAY MEASUREMENTS - DMEAS
Syntax: dmeas
The dmeas command is only visible when the application is logged in. The command is used to
display the current measurements on sessions between clients and the host. Only counters,
which are non-zero, shall be displayed.
The per session measurements available are as follows:
Measurement Description
Number of Messages from the Printer to the Host.
Number of Bytes from the Printer to the Host.
Number of Messages from the Host to the Printer.
Number of Bytes from the Host to the Printer.
3.20 CLEAR MEASUREMENTS - CLR
Syntax: clr
The measurements displayed with the dmeas command are aggregated until cleared. The clr
command will set all measurements to zero. The command has no arguments.
4 APPLICATION SOFTWARE INSTALLATION &
UPGRADE
An application may be initially installed, or upgraded, using the install command.
Refer to the DT-6XXX Platform User's Manual and refer to the section titled: Application
Software Installation & Upgrade

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 19
5 HARDWARE WARRANTY
The warranty period for the DT-6XXX hardware on which this application runs shall be ninety (90)
days from the date of shipment of the hardware from Datatek Applications, Inc. Replacements
and repairs are guaranteed for the longer of the remaining original warranty period or 30 days.
6 END-USER LICENSE AGREEMENT FOR
SOFTWARE
This License Agreement ("License") is a legal contract between you and the manufacturer
("Manufacturer") of the system ("HARDWARE") with which you acquired software product(s)
identified above ("SOFTWARE"). The SOFTWARE may include printed materials that accompany
the SOFTWARE. Any software provided along with the SOFTWARE that is associated with a
separate end-user license agreement is licensed to you under the terms of that license
agreement. By installing, copying, downloading, accessing or otherwise using the SOFTWARE,
you agree to be bound by the terms of this LICENSE. If you do not agree to the terms of this
LICENSE, Manufacturer is unwilling to license the SOFTWARE to you. In such event, you may
not use or copy the SOFTWARE, and you should promptly contact Manufacturer for instructions
on return of the unused product(s) for a refund.
6.1 SOFTWARE LICENSE
You may only install and use one copy of the SOFTWARE on the HARDWARE (unless otherwise
licensed by Manufacturer). The SOFTWARE may not be installed, accessed, displayed, run,
shared or used concurrently on or from different computers, including a workstation, terminal or
other digital electronic device (“Devices”). Notwithstanding the foregoing and except as otherwise
provided below, any number of Devices may access or otherwise utilize the services of the
SOFTWARE. You may not reverse engineer, decompile, or disassemble the SOFTWARE, except
and only to the extent that such activity is expressly permitted by applicable law notwithstanding
this limitation. The SOFTWARE is licensed as a single product. Its component parts may not be
separated for use on more than one HARDWARE. The SOFTWARE is licensed with the
HARDWARE as a single integrated product. The SOFTWARE may only be used with the
HARDWARE as set forth in this LICENSE. You may not rent, lease or lend the SOFTWARE in
any manner. You may permanently transfer all of your rights under this LICENSE only as part of
a permanent sale or transfer of the HARDWARE, provided you retain no copies, you transfer all
of the SOFTWARE (including all component parts, the media and printed materials, any
upgrades, this LICENSE and, if applicable, the Certificate(s) of Authenticity), and the recipient
agrees to the terms of this LICENSE. If the SOFTWARE is an upgrade, any transfer must also
include all prior versions of the SOFTWARE. Without prejudice to any other rights, Manufacturer
may terminate this LICENSE if you fail to comply with the terms and conditions of this LICENSE.
In such event, you must destroy all copies of the SOFTWARE and all of its component parts.
6.2 INTELLECTUAL PROPERTY RIGHTS
The SOFTWARE is licensed, not sold to you. The SOFTWARE is protected by copyright laws
and international copyright treaties, as well as other intellectual property laws and treaties. You
may not copy the printed materials accompanying the SOFTWARE. All title and intellectual
property rights in and to the content which may be accessed through use of the SOFTWARE is
the property of the respective content owner and may be protected by applicable copyright or
other intellectual property laws and treaties. This LICENSE grants you no rights to use such

DT-6XXX BiSynctoAsyncASCIIPrinterApplication User's Manual
Build 9.0
04/18/06 Datatek Applications Inc. 20
content. All rights not expressly granted under this LICENSE are reserved Manufacturer and its
licensors (if any).
6.3 SOFTWARE SUPPORT
SOFTWARE support is not provided by Manufacturer, or its affiliates or subsidiaries separate
from the HARDWARE. For SOFTWARE support, please contact your supplier of the
HARDWARE. SOFTWARE support is limited to the warranty period stated below unless either a
separate contract has been consummated between you and the manufacturer or the
manufacturer has agreed in writing at the time of purchase by you of the software to an extension
of the warranty. Should you have any questions concerning this LICENSE, or if you desire to
contact Manufacturer for any other reason, please refer to the address provided in the
documentation for the HARDWARE.
6.4 EXPORT RESTRICTIONS
You agree that you will not export or re-export the SOFTWARE to any country, person, or entity
subject to U.S. export restrictions. You specifically agree not to export or re-export the
SOFTWARE: (i) to any country to which the U.S. has embargoed or restricted the export of goods
or services, which as of March 1998 include, but are not necessarily limited to Cuba, Iran, Iraq,
Libya, North Korea, Sudan and Syria, or to any national of any such country, wherever located,
who intends to transmit or transport the products back to such country; (ii) to any person or entity
who you know or have reason to know will utilize the SOFTWARE or portion thereof in the
design, development or production of nuclear, chemical or biological weapons; or (iii) to any
person or entity who has been prohibited from participating in U.S. export transactions by any
federal agency of the U.S. government.
6.5 LIMITED WARRANTY
Manufacturer warrants that (a) the SOFTWARE will perform substantially in accordance with the
accompanying written materials for a period of ninety (90) days from the date of shipment from
Datatek Applications, Inc. Software support is limited to the hours of 9 AM to 5 PM ET Monday
through Friday excluding Datatek-observed holidays. Other coverage and extended warranty may
be purchased at additional cost. Any implied warranties on the SOFTWARE are limited to ninety
(90) days. Some states/jurisdictions do not allow limitations on duration of an implied warranty, so
the above limitation may not apply to you.
Manufacturer's and its suppliers' entire liability and your exclusive remedy shall be, at
Manufacturer's option, either (a) return of the price paid, or (b) repair or replacement of the
SOFTWARE that does not meet this Limited Warranty and which is returned to Manufacturer with
a copy of your receipt. This Limited Warranty is void if failure of the SOFTWARE has resulted
from accident, abuse, or misapplication. Any replacement SOFTWARE will be warranted for the
remainder of the original warranty period or thirty (30) days, whichever is longer.
6.6 NO OTHER WARRANTIES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, MANUFACTURER AND ITS
SUPPLIERS DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT, WITH REGARD TO
THE SOFTWARE AND THE ACCOMPANYING WRITTEN MATERIALS. THIS LIMITED
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHERS, WHICH
VARY FROM STATE/JURISDICTION TO STATE/JURISDICTION.