dB Technologies FlexSys FMX12 Manual

www.dbtechnologies.com [e-mail]
FMX 12 Rev 1.2 cod. 420120315
Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL - Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO” -
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA BOLOG A (ITALIA)
Tel [phone] Fax [phone] www.dbtechnologies.com [e-mail]

www.dbtechnologies.com [e-mail]
FMX 12 Rev 1.2 cod. 420120315
Thank you for choosing a dBTechnologies Product!
The FMX 12 is a versatile coaxial active stage monitor. It is equipped with one 1” compression driver (1.3” voice coil),
and one 12” woofer (2” voice coil). The coverage pattern is 60° (H) x 90° (V), (the horn is rotatable) and the mechanical
design allows also the vertical usage (36 mm diameter pole mount hole). A powerful DSP can adapt the live or
playback performances to different usage scenarios. The balanced audio input allows the usage of a microphone or
a line source (a mixer or instrument).
Check the site www.dbtechnologies.com for the complete user manual!
) Unpacking
The box contains:
°1 FMX 12
°1 Mains cable (VDE)
This quick start and warranty documentation
2) Easy installation
FMX 12 is equipped with:
A –Integrated/inner handles
B – 36 mm pole mount
Those mechanical particulars were thought for an easy
use and for different configuration needs.
In case of vertical usage, please see also the EQ
configuration in “Connections and controls” section.
The acoustical design allows to face different
environments. The dispersion pattern is shown in the
upper picture.
As described, the related pattern data are:
a) vertical coverage: 90°
b) horizontal coverage: 60°
The horn is rotatable. See other information in the
complete user manual.

www.dbtechnologies.com [e-mail]
FMX 12 Rev 1.2 cod. 420120315
3) Connections and controls
All the connections and
controls are in the amplifier
panel, on the side of the
monitor:
) Balanced Audio Input
2) Input sensitivity
3) Output/Link
4) Main EQ Rotary
5) Status LEDs
6) Line/Mic switch
7) VDE input with fuse
8) Power ON/OFF switch
a) Connect the audio input ( ). In case of a
microphone, plug it and select “Mic” in the Input
sensitivity switch (6). In the other cases check that the
switch is set on “Line”. Adjust the level of Sensitivity
(2).
b) If you need to link FMX 12 to another one, please
use a cable with XLR connectors (not supplied).
Connect the Link output (3) of the first, to the balanced
Input ( ) of the second one. In the second loudspeaker,
please check that the switch (6) is set on “Line” position
and that Sensitivity (3) is set to the correct value.
c) Set properly the DSP preset using the Main EQ
Rotary (4). You can choose between:
. Live Monitor, for a single monitor use on the
stage in live performance
2. Playback Monitor, for a single monitor use on
the stage in playback performance
3. Coupled Monitors, for a double monitor live
usage
4. Male Singer, to enhance male vocal
performance
5. Female Singer, to enhance female vocal
performance
6. Antifeedback, to avoid Larsen effect in live
performaces
7. Live on Stand, for an optimization of the
monitor in vertical usage and live performance
8. Playback on Stand for an optimization of the
monitor in vertical usage and playback
performance
d) Plug properly the mains VDE input cable (supplied)
in the related input (7). Then switch the POWER switch
(8) to “O ” position. Increase gradually the volume of
the audio source to the desired level.
Check the complete user manual on www.dbtechnologies.com
for further information about the system and available
accessories.
Scarica il manuale completo da www.dbtechnologies.com per
ogni ulteriore informazione sul sistema e sugli accessori
disponibili.
Für weitere Informationen und verfügbares Zubehör lesen sie
bitte die vollständige Bedienungsanleitung unter
www.dbtechnologies.com.
Vérifiez le manuel de l'utilisateur complet sur
www.dbtechnologies.com pour des informations
complémentaires du système et des accessoires disponibles.
Compruebe el manual de usuario completo sobre
www.dbtechnologies.com para la información adicional sobre el
sistema y accesorios disponibles.

www.dbtechnologies.com [e-mail]
FMX 12 Rev 1.2 cod. 420120315
Technical Data
Speaker Type: Coaxial Active Stage Monitor
Usable Bandwidth [- 0 dB]: 52 – 9000 Hz
Frequency Response [-6 dB]: 56 – 5500 Hz
Max SPL ( m): 28 dB
HF compression driver: " Exit
HF voice coil: .3”
LF: 2”
LF Voice Coil: 2”
Crossover frequency: 740 Hz (24 dB/oct)
Horizontal dispersion: 60° (rotatable horn)
Vertical dispersion: 90° (rotatable horn)
Amplifier
PSU Technology: SMPS
Amp Class: Class-D
RMS Power: 600 W
Operating voltage ( factory internal setup ):
220-240V~ (50-60Hz) or
00- 20V~ (50-60 Hz)
Processor and user interface
Controller: 28/56 bit DSP
AD/DA Conversion: 24 bit - 48 kHz
Limiter: Peak, thermal, RMS
Controls: DSP programs rotary encoder, Line/Mic switch,
Input Sensitivity level
Input / Output
Mains connections: VDE
Signal Inputs: x balanced XLR connector
Signal Out/Link: x balanced XLR connector
Mechanics
Housing: Wooden Box
Grille: Full metal grille
Pole Mount Hole: Yes, 36 mm
Width: 465 mm ( 8.30 in)
Height: 297 mm ( .69 in)
Depth: 444 mm ( 7.48 in)
Weight: 3.9 kg (30.6 lbs)
EMI CLASSIFICATION
According to the standards E 55032 and E 55035 this equipment is designed and suitable to operate in class B electromagnetic
environments.
FCC CLASS B STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful
interference,and (2)this device must accept any interference received,including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
OTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.dBTechnologies reserves the right to make
changes or improvements in design or manufacturing without assuming any obligation to change or improve products previously
manufactured.
Scan with your QR Reader
App to download the
complete User Manual
Download the complete user manual from the site:
www.dbtechnologies.com/E /Downloads.aspx