De Haardt Xtra.Mini Remote Control User manual

USER MANUAL
User Manual Xtra.Mini Remote Control V2.1
- 1 -
Xtra.Mini Remote Control
Our Xtra.Mini Remote Control gives you the possibility to
further extend the safety on your track in a cost effective
way. This mini remote has 6 buttons which have a
dedicated function.
The Xtra.Mini Remote Control is supplied with a key cord
making it very easy to carry around the track.
Usage
The Xtra.Mini Remote Control can be used in fuel or EV mode. See configuration for more
information.
By default the Xtra.Mini Remote Control is configured for fuel karts.
The speed buttons have fixed RPM values for fuel karts:
Button
Function in fuel mode
SPD1
All fuel karts 2100 RPM (speed 1)
SPD2
All fuel karts 3000 RPM (speed 2)
SPD3
All fuel karts 4000 RPM (speed 3)
SPD4
All fuel karts unlimited
STOP
All karts STOP
For EV karts the Xtra.Mini Remote Control can set speeds 1 to 4. The actual speed depends
on the switch table configuration and the settings of the motor controller. These settings are
outside the scope of this manual and cannot be configured by the Xtra.Mini Remote Control.
The speed buttons have fixed speed value for EV karts:
Button
Function in EV mode
SPD1
All EV karts Speed 1
SPD2
All EV karts Speed 2
SPD3
All EV karts Speed 3
SPD4
All EV karts Speed 4
STOP
All karts STOP
After successfully sending the speed or stop command, the indication LED of the Xtra.Mini
Remote Control will flash briefly.
When the battery of the Xtra.Mini Remote Control is low, the indication LED will flash 4
times after trying to send the speed or stop command. Correct transmission of the command
is not guaranteed when the battery is low.

USER MANUAL
User Manual Xtra.Mini Remote Control V2.1
- 2 -
Configuration
The Xtra.Mini Remote Control is by default configured for fuel karts, with tracks A, B, C and D
activated.
To change the configuration of the Xtra.Mini Remote Control hold the SHIFT key until the
indication LED is illuminated continuously.
By pressing the SPD keys, the active tracks can be toggled, the STOP key can be used to
toggle between fuel or EV karts.
When you have entered the required configurations, press the SHIFT key again to validate
your choices.
If the SHIFT key is not pressed again within 10 seconds, the Xtra.Mini Remote Control will go
back to the normal mode and changes will not be saved.
Button
Configuration
LED blinks twice
LED blinks once
SPD1
Toggle Track A
Track A enabled
Track A disabled
SPD2
Toggle Track B
Track B enabled
Track B disabled
SPD3
Toggle Track C
Track C enabled
Track C disabled
SPD4
Toggle Track D
Track D enabled
Track D disabled
STOP
Toggle between fuel
and EV karts.
EV karts are
selected
Fuel karts are selected
Operating range
The range of the Xtra.Mini Remote Control is less than the Xtra.Remote Control due to
limitations of the battery. The range of the Xtra.Mini Remote Control can be extended by the
use of an Xtra.Range Extender/Access point.
Replacing the battery
To replace the battery a standard screwdriver size/type PH0 is needed. Unscrew the
backside of the Xtra.Mini Remote control. Take care not to lose the screw and foam
material. Remove the old battery carefully. Place the new battery by sliding it in the battery
holder.
Attention: Only use CR2430 lithium coin cell as a replacement battery.

USER MANUAL
User Manual Xtra.Mini Remote Control V2.1
- 3 -
Specifications
Buttons
6, 4 speeds, 1 stop and 1 for configuring
Tracks
Any combination of 4 tracks
Function assignment
Fixed
Speed limit control (FUEL) karts (all karts only)
Stop, 2100, 3000, 4000 RPM, no limit
Speed limit control (EV) karts (all karts only)
Stop, Speed 1, 2, 3, no limit
Additional commands
On request
Indicator
Low power LED
Operation range
50 m*
Batteries
1 x CR2430 lithium coin cell
Dimensions (LxWxT)
76.5 x 43.5 x 18.5 mm
Weight
20g including battery
Operation temperature
0 … +55 degrees Celsius
Operation humidity
Max 85% relative
IP Rating
41
* The operating range of the Xtra.Mini Remote Control differs depending on the user, the way the transmitter is held, the location and other
conditions.
Warranty
1. De Haardt bv guarantees for 12 months after delivery of the goods sold or provided for use that the goods can
perform the tasks stated in the manuals, descriptions and documentation;
2. The liability under the guarantee contained in this article is limited at De Haardt bv’s choice to remedying material
and manufacturing faults free of charge in De Haardt bv’s own workshop, supplying new parts free of charge and
taking back and acquiring the ownership of the non-functioning parts, or applying a price reduction by agreement
with the other party on the goods supplied or provided for use. De Haardt bv cannot under any circumstances be
obliged to come to the location of the delivered goods to establish defects claimed by the other party. Equally, De
Haardt bv cannot be compelled to carry out repair work outside its own workshop.
3. The guarantee referred to in the third paragraph does not cover the costs of disassembly, labour costs, transport
costs and call-out charges, all in the most general sense. These costs will be charged in all cases.
4. No guarantee is provided if:
changes have been made to the goods supplied by or provided for use by De Haardt bv other than by De Haardt bv
itself or persons expressly authorized by De Haardt bv, unless De Haardt bv has agreed in writing to such changes
in advance;
the defects in the goods supplied or provided for use by De Haardt bv are the result of:
neglect of the maintenance of the goods supplied or provided for use by the other party or other users;
improper use or use not in accordance with the instructions supplied by De Haardt bv for the installation of the
goods;
incompetent use and/or misuse of the goods supplied or provided for use by the other party or other users;
wear and tear;
repairs or replacements carried out by persons other than those expressly authorized to do so by De Haardt bv,
unless De Haardt bv has agreed in writing to such repairs or replacements in advance.
5. Work not covered by the guarantee as referred to in this article shall be charged to the other party in accordance
with De Haardt bv’s relevant current tariffs.
6. Notwithstanding the provisions in the preceding paragraphs, the guarantee provided by De Haardt bv does not go
beyond any guarantee provided to De Haardt bv by the relevant manufacturer or supplier of the hardware and/or
software and fulfilled in respect of De Haardt bv. De Haardt bv shall on the other party’s request inform the latter
of the content of the contracts entered into between De Haardt and its suppliers.