Dell POWEREDGE 1900 User manual

www.dell.com | support.dell.com
Dell™ PowerEdge™ 1900 Systems
Getting Started
With Your System
系统使用入门
開始使用系統
はじめに
시스템시작하기

www.dell.com | support.dell.com
Dell™ PowerEdge™ 1900 Systems
Getting Started
With Your System

Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2006 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarksusedinthistext:DellandtheDELLlogoaretrademarksofDell,Inc.;IntelandXeonareregisteredtrademarksofIntelCorporation;
MicrosoftandWindowsareregisteredtrademarkandWindowsServerisatrademarkofMicrosoftCorporation;RedHatisaregisteredtrademark
of Red Hat, Inc.; SUSE is a registered trademark of SUSE LINUX Products GmbH.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model ECM01
February 2006 P/N GF501 Rev. A00

Getting Started With Your System 3
System Features
The major hardware and software features of your system include:
• One or two Dual-Core Intel
®
Xeon
®
Processors 5000 Sequence.
• Support for symmetric multiprocessing (SMP), which is available on systems with two Intel Xeon
processors. SMP greatly improves overall system performance by dividing processor operations
between independent processors. To take advantage of this feature, you must use an operating
system that supports multiprocessing.
NOTE: If you decide to upgrade your system by installing a second processor, you must order the
processor upgrade kits from Dell. Not all versions of the Intel Xeon processor will work properly as
additional processors. The upgrade kit from Dell contains the correct version of the processor and heat
sink.
• A minimum of 512 MB of 533 or 667 MHz (when available), Fully Buffered DIMMs (FBD),
upgradable to a maximum of 16 GB by installing combinations of 256-MB, 512-MB, 1-GB or 2-GB
memory modules in the eight memory module sockets on the system board.
• Support for up to six 3.5-inch, internal Serial-Attached SCSI (SAS) hard drives or six 3.5-inch,
internal SATA hard drives.
• Peripheral bay provides support for an optional optical drive and an optional half-height tape
backup unit (TBU).
• An optional single, 1.44-MB, 3.5-inch diskette drive.
• An optional CD, DVD, or combination CD-RW/DVD drive.
NOTE: DVD devices are data only.
• An intrusion switch that signals the appropriate systems management software if the top cover
is opened.
• An 800-W power supply.
• Six system cooling fans.
The system board includes the following features:
• Six PCI slots located in an expansion-card cage. Slots 1 and 2 are 3.3-V, 64-bit, 133-MHz PCI-X
slots; slot 3 is a 3.3-V, PCIe x8 lane; slots 4 through 6 are 3.3-V, PCIe x4 lanes. Expansion-card slots
2 through 6 accommodate full-height, full-length expansion cards. Slot 1 accommodates half-
length expansion cards. PCIe slots accommodate up to x8 expansion cards.

4Getting Started With Your System
• Dedicated PCI slot for an optional integrated RAID controller card.
NOTE: System boot is not supported from an external device attached to a SAS or SCSI adapter, including
SAS 5/E, PERC 5/E, or PERC 4e/DC. Contact your technical support provider for the latest support information
about booting from external devices.
• An integrated Gigabit Ethernet NIC, capable of supporting 10-Mbps, 100-Mbps, and 1000-Mbps data
rates.
• Six USB 2.0-compliant connectors (two on the front and four on the back) capable of supporting
a diskette drive, a CD-ROM or DVD-ROM drive, a keyboard, a mouse, or a USB flash drive.
• Optional remote access controller (RAC) for remote systems management.
• An integrated VGA-compatible video subsystem with an ATI ES1000, 33-MHz PCI video controller.
This video subsystem contains 16 MB of DDR SDRAM video memory (nonupgradable). Maximum
resolution is 1600 x 1200 with 64 K colors; true-color graphics are supported in the following
resolutions: 640 x 480, 800 x 600, 1024 x 768, 1152 x 864, and 1280 x 1024. When the optional RAC
is installed, the video resolution is 1024 X 768.
• Systems management circuitry that monitors operation of the system fans as well as critical system
voltages and temperatures. The systems management circuitry works in conjunction with the systems
management software.
• Standard baseboard management controller with serial access.
• Back-panel connectors include one serial, one video, four USB, and one NIC connector.
• Front-panel connectors include a video and two USB connectors.
• Front-panel 1x5 LCD for system ID and error messaging.
• System ID button on the front and back panels.
For more information about specific features, see "Technical Specifications" on page 9.
Supported Operating Systems
• Microsoft
®
Windows Server™ 2003 Standard and Enterprise Editions
• Microsoft Windows Small Business Server 2003, Standard and Premium Editions
• Microsoft Windows Server 2003 Standard and Enterprise x64 Editions
•RedHat
®
Enterprise Linux AS and ES (version 3 and version 4) for Intel x86
• Red Hat Enterprise Linux AS and ES (version 4) for Intel Extended Memory 64 Technology
(Intel EM64T)
•SUSE
®
Linux Enterprise Server 9 for Intel EM64T

Getting Started With Your System 5
Other Information You May Need
CAUTION: The Product Information Guide provides important safety and regulatory information. Warranty
information may be included within this document or as a separate document.
• The Hardware Owner’s Manual provides information about system features and describes how to
troubleshoot the system and install or replace system components. The
Hardware Owner’s Manual
is available on the CDs that came with your system or from support.dell.com .
• CDs included with your system provide documentation and tools for configuring and managing
your system.
• Updates are sometimes included with the system to describe changes to the system, software, and/or
documentation.
NOTE: Always check for updates on support.dell.com and read the updates first because they often
supersede information in other documents.
• Release notes or readme files may be included to provide last-minute updates to the system or
documentation or advanced technical reference material intended for experienced users or
technicians.
Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system does not perform as expected,
see your Hardware Owner’s Manual.
Installation and Configuration
CAUTION: Before performing the following procedure, read and follow the safety instructions and important
regulatory information in your Product Information Guide.
This section describes the steps to set up your system for the first time. Refer to the documentation
included with your system on installing the stabilizer feet on your system.
CAUTION: Installing the feet is necessary to provide a stable foundation for the system. Failure to install the feet
poses the risk of having the system tip over, possibly causing bodily injury or damage to the system.
CAUTION: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift the
system by yourself.

6Getting Started With Your System
Unpacking the System
Unpack your system and identify each item.
Keep all shipping materials in case you need them later.
Installing the Stabilizer Feet
See the documentation included with your system on installing the system stabilizer feet.

Getting Started With Your System 7
Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable to plug into each
connector. Be sure to tighten the screws (if any) on the monitor's cable connector.
Connecting the Power
Attach the system’s power cable to the cable clasp at the top of the power supply and connect it
to the system.
Plug the other end of the cable into a grounded electrical outlet or a separate power source
such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

8Getting Started With Your System
Turning on the System
Turn on the system and monitor (optional).
Press the power button on the system and the monitor. The power indicators should light.
Adjust the monitor’s controls until the displayed image is satisfactory.
Installing the Bezel
Install the bezel.

Getting Started With Your System 9
Complete the 0perating System Setup
If you purchased a preinstalled operating system, see the operating system documentation that ships
with your system. To install an operating system for the first time, see the Quick Installation Guide.
Be sure the operating system is installed before installing hardware or software not purchased with
the system.
Technical Specifications
Processor
Processor type One or two Dual-Core Intel Xeon Processors 5000
Sequence
Expansion Bus
Bus type PCI, PCI-X, PCIe
Expansion slots
PCI-X one full-height, half-length 3.3-V, 64-bit,
133-MHz (slot 1)
one full-height, full-length 3.3-V, 64-bit, 133-MHz
(slot 2)
PCIe one x8 lane, 3.3-V (slot 3)
three x4 lanes, 3.3-V (slots 4 through 6)
Memory
Architecture 533 or 667 MHz (when available) Fully Buffered
DIMMs (FBD)
Memory module sockets eight 240-pin
Memory module capacities 256 MB, 512 MB, 1 GB, or 2 GB
Minimum RAM 512 MB (two 256-MB modules)
Maximum RAM 16 GB
Drives
Hard drives up to six 3.5-inch, internal, SAS or SATA
Diskette drive one optional internal 3.5-inch, 1.44-MB
optional external USB 3.5-inch, 1.44-MB

10 Getting Started With Your System
Optical drive one optional CD, DVD, or combination
CD-RW/DVD
NOTE: DVD devices are data only.
optional external USB CD-ROM
optional external USB DVD-ROM
Flash drive optional external USB
Connectors
Back
NIC TOE-capable RJ-45 (for integrated 1-GB NIC)
Serial 9-pin, DTE, 16550-compatible
USB Four 4-pin, USB 2.0-compliant
Video 15-pin VGA
Front
Video 15-pin VGA
USB Two 4-pin, USB 2.0-compliant
Video
Video type ATI ES1000 video controller; VGA connectors
Video memory 16 MB of DDR SDRAM
Power
AC power supply
Wattage 800 W
Voltage 90–264 VAC, autoranging, 47–63 Hz
Heat dissipation 2320 BTU/hr maximum
Maximum inrush current Under typical line conditions and over the entire
system ambient operating range, the inrush
current may reach 55 A per power supply for
10 ms or less
Batteries
System battery CR 2032 3.0-V lithium ion coin cell
RAID battery (optional) 4.1-V lithium ion
Drives (continued)

Getting Started With Your System 11
Physical
Tower (without bezel)
Height 47.89 cm (18.85 in) with feet, no casters
Width 22.66 cm (8.92 in)
Depth 66.13 cm (26.04 in) does not include control
panel or bezel; control panel adds an additional
1.3 cm (.51 in)
Weight (maximum configuration) 49.9 kg (110 lb)
Environmental
NOTE: For additional information about environmental measurements for specific system configurations,
contact your technical support provider.
Temperatur e
Operating 10° to 35°C (50° to 95°F)
Storage –40° to 65°C (–40° to 149°F)
Relative humidity
Operating 20% to 80% (noncondensing) with a maximum
humidity gradation of 10% per hour
Storage 5% to 95% (noncondensing)
Maximum vibration
Operating 0.26 G from 5–350Hz for 2 min in the Z axis
Storage 1.54 G from 10–250 Hz for 15 min in all
orientations
Maximum shock
Operating One shock pulse in the positive z axis (one pulse
on each side of the system) of 41 G for up to 2 ms
Storage Six consecutively executed shock pulses in the
positive and negative x, y, and z axes (one pulse
on each side of the system) of 71 G for up to 2 ms
Altitude
Operating –16 to 3048 m (–50 to 10,000 ft)
Storage –16 to 10,600 m (–50 to 35,000 ft)

12 Getting Started With Your System

www.dell.com | support.dell.com
Dell™ PowerEdge™ 1900 系统
系统使用入门

注、注意和警告
注：
注表示可以帮助您更好地使用计算机的重要信息。
注意：
注意表示可能会损坏硬件或导 数据丢失，并告诉您如何避免此类问题。
警告：
警告表示可能会导致财产损失、人身伤害甚至死亡。
____________________
本说明文件中的信息如有更改，恕不另行通知。
© 2006 Dell Inc. 版权所有，翻印必究。
未经 Dell Inc. 书 许可，严禁以任何形式进行复制。
本文中使用的商标：
Dell 和DELL 徽标是 Dell, Inc. 的商标； Intel 和Xeon 是Intel Corporation 的注册商标； Microsoft 和Windows
是Microsoft Corporation 的注册商标， Windows Server 是Microsoft Corporation 的商标； Red Hat 是Red Hat, Inc. 的注册商标；
SUSE 是SUSE LINUX Products GmbH 的注册商标。
本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。 Dell Inc. 对本公司的商标和产品名称之外
的其它商标和产品名称不拥有任何专有权。
型号 ECM01
2006 年2 月P/N GF501 修订版 A00

系统使用入门 15
系统配置
系统的主要硬件和软件配置包括：
• 一个或两个双核心
Intel
®
Xeon
®
处理器
5000
序列。
• 支持对称 处理
(SMP)
，配备两个
Intel Xeon
处理器的系统具有此功能。
SMP
通过在独立的
处理器之间分配处理器操作，从而极大地改善了系统整体性能。要使用此功能，必须使用支
持 处理的操作系统。
注：如果您准备安装第二个处理器来升级系统，则必须向 Dell 订购处理器升级套件。并非所有
版本的 Intel Xeon 处理器均可作为附加处理器正常工作。Dell 的升级套件包含正确版本的处理器
和散热器。
• 至少
512 MB
的
533
或
667 MHz
（可用时）全缓冲
DIMM (FBD)
，通过在系统板上的八个内
存模块插槽中安装
256 MB
、
512 MB
、
1 GB
或
2 GB
内存模块组合，最大可升级至
16 GB
。
• 支持 达六个
3.5
英寸、内部串行连接
SCSI (SAS)
硬盘驱动器或六个
3.5
英寸、内部
SATA
硬盘驱动器。
•
外围设备托架可支持一个可选的光盘驱动器和一个可选的半高磁带备份装置
(TBU)
。
• 一个可选的
1.44 MB 3.5
英寸软盘驱动器。
• 一个可选的
CD
、
DVD
或组合
CD-RW/DVD
驱动器。
注：DVD 设备仅用于数据。
• 防盗开关，在顶盖被打开时会向相应的系统管理软件发送信号。
• 一个
800W
电源设备。
• 六个系统冷却风扇。
系统板包含以下配置：
• 位于扩充卡固定框架上的六个
PCI
插槽。插槽
1
和
2
是
3.3 V
、
64
位、
133 MHz PCI-X
插槽；
插槽
3
是一个
3.3 V
、
PCIe x8
信道插槽；插槽
4
至插槽
6
是
3.3 V
、
PCIe x4
信道插槽。扩充
卡插槽
2
到
6
中可以安装全高、全长扩充卡。插槽
1
可以安装半长扩充卡。
PCIe
插槽可以安
装 达
x8
个扩充卡。

16 系统使用入门
• 专用
PCI
插槽，用于安装可选的集成
RAID
控制器卡。
注：不支持从连接到 SAS 或SCSI 适配器的外部设备引导系统，包括 SAS 5/E、PERC 5/E 或
PERC 4e/DC。有关支持从外部设备引导的最新信息，请与您的技术支持提供商联系。
• 一个集成的千兆位以太网
NIC
，可支持
10 Mbps
、
100 Mbps
和
1000 Mbps
数据速率。
• 六个
USB 2.0
兼容连接器 （两个在正面，四个在背面），可以支持软盘驱动器、
CD-ROM
或
DVD-ROM
驱动器、键盘、鼠标或
USB
快擦写驱动器。
• 可选的远程访问控制器
(RAC)
，用于远程系统管理。
•VGA 兼容集成视频子系统，带有
ATI ES1000
、
33 MHz PCI
视频控制器。此视频子系统包含
16 MB
的
DDR SDRAM
视频内存 （不可升级）。使用
64 K
色时最大分辨率为
1600
x
1200
；
以下分辨率支持真彩色图形：
640
x
480
、
800
x
600
、
1024
x
768
、
1152
x
864
和
1280
x
1024
。
如果安装了可选的
RAC
，则视频分辨率为
1024
x
768
。
• 系统管理电路，可监测系统风扇的运行以及系统临界电压和温度。系统管理电路需要与系统管理
软件配合工作。
• 标准底板管理控制器，支持串行访问。
• 背面板连接器包括一个串行连接器、一个视频连接器、四个
USB
连接器和一个
NIC
连接器。
•
前面板连接器包括一个视频连接器和两个
USB
连接器。
•
前面板
1
x
5 LCD
显示屏，用于显示系统
ID
和错误信息。
• 系统
ID
按钮，位于前面板和背面板上。
有关特定配置的详细信息，请参阅第
21
页的 “技术规格”。
支持的操作系统
•Microsoft
®
Windows Server™2003
标准版和企业版
•Microsoft Windows Small Business Server 2003
标准版和高级版
•Microsoft Windows Server 2003 标准版和企业版 （
64
位）
• 用于
Intel x86
的
Red Hat
®
Enterprise Linux AS
和
ES
（第
3
版和第
4
版）
• 用于
Intel 64
位扩展内存技术
(Intel EM64T)
的
Red Hat Enterprise Linux AS
和
ES
（第
4
版）
• 用于
Intel EM64T
的
SUSE
®
Linux Enterprise Server 9

系统使用入门 17
您可能需要的其它信息
警告：《产品信息指南》提 了重要的安全信息和管制信息。保修信息可能包括在该说明文件中，
也可能作为单独的说明文件提 。
• 《硬件用户手册》提供了有关系统部件的信息，并介绍了如何排除系统故障以及如何安装或更换
系统组件。《硬件用户手册》可在随系统提供的
CD
或在
support.dell.com
上获得。
• 随系统附带的
CD
提供了用于配置和管理系统的说明文件和工具。
• 系统有时附带更新，用于说明对系统、软件和／或说明文件所做的更改。
注：请始终检查
support.dell.com
上的更新信息并首先进行阅读，因为该网站上的信息常常会取代
其它说明文件中的信息。
• 系统可能会附带发行说明或自述文件，以提供系统或说明文件的最新更新内容，或者为有经验的
用户或技术人员提供高级技术参考资料。
获得技术帮助
如果您对本指南中的步骤有疑问，或系统运行无 达到预期效果，请参阅 《硬件用户手册》。
安 和配置
警告：在执行以下过程之前，请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。
本节介绍初次安装系统时的步骤。请参阅随系统提供的说明文件在系统上安装稳定支脚。
警告：要为系统提 稳固的基础，需要安装支脚。如果未安装支脚，可能存在导致系统倾翻的危险，
从而可能造成人身伤害或损坏系统。
警告：无论何时您需要抬起系统，均需找他人协助。为了避免造成伤害，请勿尝试自行抬起系统。

18 系统使用入门
打开系统包装
打开系统包装并识别每项物品。
妥善保管所有运输包装材料，以备将来使用。
安装稳定支脚
参阅随系统提供的说明文件安装系统稳定支脚。