Dell PowerEdge C6320 User manual

Dell PowerEdge C6320
Getting Started
With Your System
Začínáme se systémem
Mise en route du système
Erste Schritte mit dem System
Τα πρώτα βήματα στο σύστημά σας
Rozpoczynanie pracy z systemem
Начало работы ссистемой
Početak rada sa sistemom
Procedimientos iniciales con el sistema
Sisteminizi Kullanmaya Başlarken
תליחתהדובעהםעתכרעמה

Scan to see how-to videos, documentation, and
troubleshooting information.
Naleznete zde videa s postupy, dokumentaci
a informace o řešení potíží.
Scannez pour voir des didacticiels vidéo, obtenir de la
documentation et des informations de dépannage.
Scannen, um Videos zu Hilfe und Anleitungen, Dokumentationen
und Informationen zur Fehlerbehebung zu sehen.
Αναζητήστε βίντεο για τον τρόπο χρήσης του συστήματος,
τεκμηρίωση και πληροφορίες για την αντιμετώπιση προβλημάτων.
Zeskanuj, aby wyświetlićinstruktażowe filmy wideo
i informacje o rozwiązywaniu problemów.
Сканируйте, чтобы просмотреть обучающее видео,
документацию иинформацию по устранению неисправностей.
Skenirajte da biste videli video uputstva, dokumentaciju
i informacije o rešavanju problema.
Escaneo para ver vídeos sobre procedimientos, documentación
e información para la solución de problemas.
Tarama nasıl yapılır videoları, belgeler ve
sorun giderme bilgilerini görmek için.
קורסידכתוארלעדימיבגלינוטרסהכרדה,דועיתןורתפותויעב.

Dell PowerEdge
C6320
Getting Started
With Your System

Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better
use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or
loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.

______________
Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international
copyright and intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the
United States and/or other jurisdictions. All other marks and names mentioned herein may be
trademarks of their respective companies.
Regulatory Model: B08S Regulatory Type: B08S003
2015 - 03 P/N CFK9F Rev. A00

6 | Getting Started With Your System
CAUTION: Restricted Access Location
This server is intended for installation only in restricted access locations as defined in
Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:
•Access can only be gained by service persons or by users who have been
instructed about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
•Access is through the use of a tool or lock and key, or other means of security,
and is controlled by the authority responsible for the location.
Installation and Configuration
WARNING: Before performing the following procedure, review and follow
the safety instructions that came with the system.
Installing the Tool-Less Rail Solution
WARNING: Whenever you need to lift the system, get others to assist
you. To avoid injury, do not attempt to lift the system by yourself.
WARNING: The system is not fixed to the rack or mounted on the
rails. To avoid personal injury or damage to the system, you must
adequately support the system during installation and removal.
WARNING: To avoid a potential electrical shock hazard, a third wire
safety grounding conductor is necessary for the rack installation.
The rack equipment must provide sufficient airflow to the system to
maintain proper cooling.
CAUTION: When installing rails in a square-hole rack it is important
to ensure that the square peg slides through the square holes.

Getting Started With Your System | 7
1 Push the latch release buttons on the midpoints of the end piece to open the
rail latches. See Figure 1.
2 Align the end pieces of the rails on the vertical rack flanges to seat the pegs
in the bottom hole of the first U and the top hole of the second U.
NOTE: The rails can be used in both square-hole (item 1 in the
following figure) and round-hole racks (item 2 in the following figure).
Figure 1. Pushing the Latch Release Buttons
NOTE: To remove the rails, push the latch release button on the
midpoints of the end piece and unseat each rail.

8 | Getting Started With Your System
3 Engage the end of the rails and release the latch release button to have the
latches locked in place. See Figure 2.
Figure 2. Releasing the Latch Release Buttons
4 On each vertical rack flange on the back, put two screw bases into the two
square holes right above the rail. See Figure 3.
5 Install the chassis stabilizer shipping brackets (optional) on the back rack
flanges.

Getting Started With Your System | 9
6 Install and tighten the screws.
NOTE: To transport systems already installed in the rack, ensure that
the two chassis stabilizer shipping brackets (optional) are in place.
Figure 3. Installing the Chassis Stabilizer Shipping Brackets

10 | Getting Started With Your System
7 Slide the system into the rack. See Figure 4.
8 Tighten the thumbscrews to secure the ears of the system to the front of the
rack flanges.
Figure 4. Installing the Chassis onto the Rack.