Dell PowerEdge E04S001 User manual

Dell™ PowerEdge™
T710 Systems
Getting Started
With Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema

Dell™ PowerEdge™
T710 Systems
Getting Started
With Your System
Model E04S
Regulatory type E04S001

Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use
of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data
if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
____________________
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.;
Intel and Xeon are registered trademarks of Intel Corporation in the U.S. and other countries; Microsoft,
Windows,Windows Server,and Hyper-V are either trademarks or registered trademarks of Microsoft
Corporation in the United States and/or other countries; Red Hat and Enterprise Linux are registered
trademarks of Red Hat, Inc. in the United States and other countries; SUSE is a registered trademark
of Novell, Inc. in the United States and other countries; VMware is a registered trademark of VMware, Inc.
in the United States and/or other jurisdictions; Citrix and XenServer are trademarks of Citrix Systems, Inc.
and/or more of its subsidiaries, and may be registered in the United States Patent and Trademark Office
and in other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and
trade names other than its own.
Model E04S
Regulatory type E04S001
March 2009 P/N N732H Rev. A00

Getting Started With Your System 3
Installation and Configuration
WARNING: Before performing the following procedure, review the safety
instructions that came with the system.
NOTE: If you are using the optional rack configuration, assemble the rails
and install the system in the rack following the safety instructions and the
rack installation instructions provided with your system.
Stabilizing the Tower System
WARNING: The tower system has four feet on its bottom panel that can be
extended outward to help properly stabilize the system. Failure to extend the feet
poses the risk of having the system tip over, possibly causing bodily injury
or damage to the system.

4Getting Started With Your System
Optional – Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable
to plug into each connector. Be sure to tighten the screws (if any) on the
monitor's cable connector.
Connecting the Power Cable(s)
Connect the system’s power cable(s) to the system and, if a monitor is used,
connect the monitor’s power cable to the monitor.

Getting Started With Your System 5
Securing the Power Cable(s)
Bend the system power cable(s) into a loop as shown in the illustration
and secure the cable with the provided strap.
Plug the other end of the power cable(s) into a grounded electrical outlet
or a separate power source such as an uninterrupted power supply (UPS)
or a power distribution unit (PDU).
Turning On the System
Press the power button on the system and on the optional monitor, if used.
The power indicators should light.

6Getting Started With Your System
Complete the Operating System Setup
If you purchased a preinstalled operating system, see the operating system
documentation that ships with your system. To install an operating system for
the first time, see the installation and configuration documentation for your
operating system. Be sure the operating system is installed before installing
hardware or software not purchased with the system.
Supported Operating Systems
• Microsoft
®
Windows
®
Small Business Server 2008 Standard and
Premium (x64) editions
• Microsoft Windows Small Business Server 2008 Standard and
Premium editions with SP2
• Microsoft Windows Small Business Server 2003 R2 Standard and
Premium (32-bit x86) editions
• Microsoft Windows Server
®
2008 Standard and Enterprise (32-bit x86)
editions
• Microsoft Windows Server 2008 Standard, Enterprise, and Datacenter
(x64) editions
• Microsoft Windows Server 2008 Standard, Enterprise, and Datacenter
editions with SP2
• Microsoft Windows Essential Business Server 2008 Standard
and Premium editions with SP2
• Microsoft Windows Server 2003 Standard and Enterprise (32-bit x86)
editions with SP2
• Microsoft Windows Server 2003 Standard and Enterprise (x64) editions
(SP1 and later)
• Microsoft Windows Server 2003 R2 Standard and Enterprise (32-bit x86)
editions with SP2
• Microsoft Windows Server 2003 R2 Standard, Enterprise, and Datacenter
(x64) editions (SP1 and later)
•RedHat
®
Enterprise Linux
®
AS and ES (Version 4) (x86)
• Red Hat Enterprise Linux AS and ES (Version 4) (x86_64)
• Red Hat Enterprise Linux Server 5 (x86)

Getting Started With Your System 7
• Red Hat Enterprise Linux Server 5 (x86_64)
•SUSE
®
Linux Enterprise Server 10 SP2 (x86_64)
• SUSE Linux Enterprise Server 11 (x86_64)
•VMware
®
ESX Version 3.5 Update 4
• VMware ESX Version 4.0
• VMware ESXi Version 3.5 Update
x (embedded)
• VMware ESXi Version 4.0 (embedded)
•Citrix
®
XenServer™ Enterprise edition 5. x (embedded)
• Microsoft Hyper-V™
NOTE: For the latest information on supported operating systems,
see www.dell.com.
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with
your system. Warranty information may be included within this document
or as a separate document.
• The rack documentation included with your rack solution describes
how to install your system into a rack.
• The
Hardware Owner’s Manual provides information about system features
and describes how to troubleshoot the system and install or replace system
components. This document is available online at
support.dell.com .
• Any media that ships with your system that provides documentation
and tools for configuring and managing your system, including those
pertaining to the operating system, system management software, system
updates, and system components that you purchased with your system.
NOTE: Always check for updates on support.dell.com and read the updates
first because they often supersede information in other documents.

8Getting Started With Your System
Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system does
not perform as expected, see your Hardware Owner’s Manual. Dell™ offers
comprehensive hardware training and certification. See www.dell.com/training
for more information. This service may not be offered in all locations.
Technical Specifications
Processor
Processor type Intel®Xeon®Processor 5500 series
Expansion Bus
Bus type PCI Express Generation 2
Expansion slots Slot 0: PCIe x8 Storage
Slot 1: PCIe x4
Slot 2: PCIe x16
Slot 3: PCIe x8
Slot 4: PCIe x8
Slot 5: PCIe x8
Slot 6: PCIe x8
NOTE: A maximum of 110W is allocated to add-in
cards. All slots support up to 25W, but a maximum of
2x 25W cards and 4x 15W cards may be installed at
any time, regardless of the slots they are installed in.
Memory
Architecture 800-Mhz, 1066-MHz, or 1333-MHz DDR3
registered or unbuffered Error Correcting Code
(ECC) DIMMs.
Memory module sockets Eighteen 240-pin
Memory module capacities 1 GB, 2 GB, 4 GB, or 8 GB (16 GB when
available)
Minimum RAM 1 GB
Maximum RAM 144 GB

Getting Started With Your System 9
Drives
Hard drives Up to sixteen 2.5-inch, hot-swap SAS/SATA/SSD
internal drives or up to eight 3.5-inch, hot-swap
SAS/SATA/SSD internal drives
NOTE: 3.5-inch SSD is supported using 2.5-inch
SSD in a 3.5-inch carrier with an insert.
Diskette drive External optional USB 1.44-MB
Optical drive Up to two optional external USB DVD-ROM
or internal DVD-ROM (SATA) or DVD+RW
(SATA)
NOTE: DVD devices are data only.
Tape drive One 5.25-inch half-height tape backup device
Connectors
Back
NIC Four RJ-45 (for integrated 1-GB NICs)
Serial 9-pin, DTE, 16550-compatible
USB Six 4-pin, USB 2.0-compliant
Video 15-pin VGA
Front
USB Two 4-pin, USB 2.0-compliant
Internal
USB One 4-pin, USB 2.0-compliant
Internal secure digital (SD)
module
One optional flash memory card slot on internal
SD module

10 Getting Started With Your System
Video
Video type Matrox G200eW video controller; VGA connector
Video memory 8 MB
Power
AC power supply (per power supply)
Wattage 1100 W
Voltage 100–240 VAC, 50/60 Hz, 8.0–4.0 A
Heat dissipation 1026 BTU/hr maximum
Maximum inrush current Under typical line conditions and over the entire
system ambient operating range, the inrush
current may reach 25 A per power supply for
10 ms or less.
Batteries
System battery CR 2032 3.0-V lithium coin cell
RAID battery (optional) 3.7-V lithium ion battery pack
Physical
Height 21.8 cm (8.6 in)
Width 43.1 cm (17 in)
Depth 69.7 cm (27.4 in)
Weight (maximum
configuration)
35.3 kg (78 lb)
Weight (empty) 26.7 kg (59 lb)

Getting Started With Your System 11
Environmental
NOTE: For additional information about environmental measurements for specific
system configurations, see www.dell.com/environmental_datasheets.
Temperature
Operating 10° to 35°C (50° to 95°F) with a maximum
temperature gradation of 10°C per hour
NOTE: For altitudes above 2950 feet, the maximum
operating temperature is derated 1ºF/550 ft.
Storage –40° to 65°C (–40° to 149°F) with a maximum
temperature gradation of 20°C per hour
Relative humidity
Operating 8% to 85% (noncondensing) with a maximum
humidity gradation of 10% per hour
Storage 5% to 95% (noncondensing)
Maximum vibration
Operating 0.25 G at 3–200 Hz for 15 min
Storage 0.5 G at 3–200 Hz for 15 min
Maximum shock
Operating One shock pulse in the positive z axis (one pulse
on each side of the system) of 31 G for 2.6 ms in
the operational orientation
Storage Six consecutively executed shock pulses in the
positive and negative x, y, and z axes (one pulse on
each side of the system) of 71 G for up to 2 ms
Altitude
Operating –16 to 3,048 m (–50 to 10,000 ft)
NOTE: For altitudes above 2950 feet, the maximum
operating temperature is derated 1ºF/550 ft.
Storage –16 to 10,600 m (–50 to 35,000 ft)
Airborne Contaminant Level
Class G2 or lower as defined by ISA-S71.04-1985

12 Getting Started With Your System

Systèmes Dell™
PowerEdge™ T710
Guide de mise
en route
Modèle E04S
Type réglementaire E04S001

Remarques, précautions et avertissements
REMARQUE : Une REMARQUE indique des informations importantes qui peuvent
vous aider à mieux utiliser votre ordinateur.
PRECAUTION : Une PRÉCAUTION vous avertit d'un risque de dommage matériel
ou de perte de données en cas de non-respect des instructions données.
AVERTISSEMENT : Un AVERTISSEMENT vous avertit d'un risque d'endom-
magement du matériel, de blessure corporelle ou de mort.
____________________
Les informations contenues dans ce document sont sujettes à modification sans préavis.
© 2009 Dell Inc. Tous droits réservés.
La reproduction de ces documents de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.
est strictement interdite.
Marques mentionnées dans ce document : Dell, le logo DELL et PowerEdge sont des marques de
Dell Inc. ; Intel et Xeon sont des marques déposées d'Intel Corporation aux États-Unis et dans d'autres
pays ; Microsoft, Windows, Windows Server et Hyper-V sont des marques ou des marques déposées
de Microsoft Corporation aux États-Unis et/ou dans d'autres pays ; Red Hat et Enterprise Linux sont
des marques déposées de Red Hat, Inc. aux États-Unis et dans d'autres pays ; SUSE est une marque
déposée deNovell,Inc.auxÉtats-Unis et dans d'autres pays ; VMware est une marque déposée de VMware,
Inc. aux États-Unis et/ou dans d'autres juridictions ; Citrix et XenServer sont des marques déposées de Citrix
Systems, Inc. et/ou d'une ou de plusieurs de ses filiales, et peuvent être déposées auprès du Patent and
Trademark Office aux États-Unis et d'organismes similaires dans d'autres pays.
D'autres marques commerciales et noms de marque peuvent être mentionnés dans ce document pour faire
référence aux entités se réclamant de ces marques et de ces noms ou de leurs produits. Dell Inc. dénie
tout intérêt propriétaire vis-à-vis des marques commerciales et des noms de marque autres que les siens.
Modèle E04S
Type réglementaire E04S001
Mars 2009 N/P N732H Rév. A00

Guide de mise en route 15
Installation et configuration
AVERTISSEMENT : Avant de commencer, consultez les consignes de sécurité
fournies avec le système.
REMARQUE : Si vous utilisez la configuration en option, assemblez les rails
et installez le système dans le rack en suivant les consignes de sécurité
et les instructions d'installation en rack fournies avec le système.
Stabilisation d'un système en tour
AVERTISSEMENT : Le système en tour est doté de quatre stabilisateurs qui
pivotent vers l'extérieur pour assurer une bonne stabilité. Si vous ne mettez pas
en place ces stabilisateurs, l'ordinateur risque de basculer, ce qui pourrait
l'endommager ou occasionner des blessures corporelles.

16 Guide de mise en route
Facultatif – Connexion du clavier, de la souris et du moniteur
Connectez le clavier, la souris et le moniteur (si nécessaire).
Les icônes des connecteurs situés à l'arrière du système indiquent où insérer
chaque câble. N'oubliez pas de serrer les vis situées sur le connecteur du câble
du moniteur, s'il en est équipé.
Branchement du ou des câbles d'alimentation
Branchez le ou les câbles d'alimentation au système et, si vous utilisez
un moniteur, connectez son câble d'alimentation à celui-ci.

Guide de mise en route 17
Fixation du ou des câbles d'alimentation
Repliez le ou les câbles d'alimentation système comme indiqué dans l'illus-
tration suivante et fixez-le(s) avec la bande fournie.
Branchez ensuite l'autre extrémité du ou des câbles sur une prise de courant
mise à la terre ou sur une source d'alimentation autonome (onduleur ou unité
de distribution de l'alimentation [PDU]).
Mise sous tension du système
Appuyez sur le bouton d'alimentation du système et du moniteur en option,
si vous l'utilisez. Les voyants d'alimentation s'allument.

18 Guide de mise en route
Terminez l'installation du système d'exploitation
Si vous avez acheté un système d'exploitation préinstallé, consultez tout
d'abord la documentation associée, fournie avec l'ordinateur. Pour une
première installation du système d'exploitation, consultez la documentation
concernant l'installation et la configuration du système d'exploitation. Veillez
à installer le système d'exploitation avant tout élément matériel ou logiciel
acheté séparément.
Systèmes d'exploitation pris en charge
• Microsoft
®
Windows
®
Small Business Server 2008, éditions Standard
et Premium (x64)
• Microsoft Windows Small Business Server 2008, éditions Standard
et Premium avec SP2
• Microsoft Windows Small Business Server 2003 R2, éditions Standard
et Premium (32 bits, x86)
• Microsoft Windows Server
®
2008, éditions Standard et Enterprise
(32 bits x86)
• Microsoft Windows Server 2008, éditions Standard, Enterprise
et Datacenter (x64)
• Microsoft Windows Server 2008, éditions Standard, Enterprise
et Datacenter avec SP2
• Microsoft Windows Essential Business Server 2008, éditions Standard
et Premium avec SP2
• Microsoft Windows Server 2003, éditions Standard et Enterprise
(32 bits, x86) avec SP2
• Microsoft Windows Server 2003, éditions Standard et Enterprise (x64)
(SP1 et ultérieur)
• Microsoft Windows Server 2003 R2, éditions Standard et Enterprise
(32 bits, x86) avec SP2
• Microsoft Windows Server 2003 R2, éditions Standard, Enterprise
et Datacenter (x64) (SP1 et ultérieur)
•RedHat
®
Enterprise Linux
®
AS et ES (version 4) (x86)
• Red Hat Enterprise Linux AS et ES (Version 4) (x86_64)