DeLonghi La Specialista Prestigio EC935X User manual

De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com 5713200041_00_0221 - Printed in China

EC935X
COFFEE MAKER
Instructions for use. Keep these instructions
Visit www.delonghi.com
for a list of service centers near you.
ELECTRIC CHARACTERISTICS
120 V~ 60 Hz 1450 W
MACHINE À CAFÉ
Mode d’emploi . Conservez cette notice
Visitez www.delonghi.com pour y voir une liste des
centres de réparation proches de chez vous.
CARACTÉRISTIQUES ÉLECTRIQUES
120 V~ 60 Hz 1450 W
CAFETERA
Repase y guarde estas instrucciones.
Lea cuidadosamente este instructivo
antes de usar su aparato.
Visite www.delonghi.com para ver la lista de
centros de servicios cercanos a usted.
CARACTERISTICAS ELECTRICAS:
120 V~ 60 Hz 1450 W

2
B2 B3 B4 B5 B6 B7 B8
B9
B10
B11
B12
B14
B13
B16
B15
B1 B17
C9
C6
C7
C1
C4
De’LonghiAppliancess.r.l.
ViaL.Seitz, 47 31100 Treviso - ITALY
Tel.[phone]
5413218631/04.15
Decalcicantepermacchine da caè
Descalerfor coee machines
Détartrantpour machines à café
Entkalkerfür Kaeemaschinen
C5
C8
C3
C2
C10
EN FR ES
page 4 page 24 pág. 45

3
A1
A20
A18
A19
A7
A8
A9
A11
A10
A5
A2 A3
A4
A6
A12
A13
A14
A15
A16
A17
A21

4
IMPORTANT SAFEGUARDS
When using electrical machines, basic safety precautions should always be followed, including the following:
• Read all instructions.
•Use this machine only as described in this instruction manual.
As with any electrical machine, the instructions aim to cover as many situations as possible. Caution and
common sense should be used when operating and installing this machine.
• To protect against re, electrical shock and personal injury, do not immerse cord, plug or machine in
water or other liquid.
• Never allow the machine to be used by children.
• Unplug from the outlet when not in use and before cleaning. Allow to cool before tting or taking o
parts, and before cleaning the machine.
• Do not operate with a damaged cord or plug, or after the machine malfunctions, or has been damaged in any
manner. Return the machine to the nearest authorized service facility for examination, repair or adjustment.
• The use of accessory attachments or spare parts not recommended by the machine manufacturer may
result in re, electrical shock or personal injury.
• Do not use outdoors.
• Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
• Do not place on or near a hot gas or electrical burner, or in a heated oven.
• Plug cord into the wall outlet.To disconnect, turn any control to“o”, then remove plug from wall outlet.
• Do not use the machine for other than the intended use. This machine is to be utilized for domestic use
only. Any other use is to be considered improper and therefore, dangerous.
WARNING: To reduce the risk of re or electric shock, do not remove the exterior of the unit or the cover.
Don’t attempt to repair or modify the machine, doing so will void the warranty. Repair should be done by
authorized service personnel only!
SAVE THESE INSTRUCTIONS
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY
SHORT CORD INSTRUCTIONS
- A short power cord is provided to reduce risks resulting from becoming entangled in or tripping over a
longer cord.
- Longer, detachable power supply cords or extension cords are available and may be used if care is exer-
cised in their use.
- If an extension cord is used, the marked electrical rating should be at least as great as the electrical rating
of the machine. If the machine is provided with 3- wire, grounding type cord, the extension should be a
GROUNDING TYPE 3 - WIRE CORD. The longer cord should be arranged so that it will not drape over the
counter-top or table top where it can be pulled on by children or tripped over.
- Your product is equipped with a polarized alternating current line plug (a plug having one blade wider
than the other).This plug will t into the power outlet only one way. This is a safety feature. If you are un-
able to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to t, contact
your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

5
1. DESCRIPTION
1.1 Description of appliance - A
A1. Beans container lid
A2. Beans container
A3. Cup tray
A4. Steam dial
A5. Hot water outlet
A6. Steam wand and nozzle
A7. Cup grille for espresso
A8. Cup grille for glasses or mugs
A9. Drip tray grille
A10. Drip tray
A11. Drip tray water level indicator
A12. Water tank lid
A13. Water tank extraction handle
A14. Water tank
A15. Water softener lter housing
A16. Power cord connector socket
A17. Main switch (ON/OFF)
A18. Coee outlet
A19. Coee mill outlet (tamping station)
A20. Presser lever
A21. Cover to access the coee mill coee guide
1.2 Description of control panel - B
B1. ON/Standby button
B2. Coee dose dial
B3. “X2”button: to use the 2 coees lter
B4. CoeeTemperature button
B5. “OK”button: to deliver the beverage/conrm
B6. Hot water button
B7. “My”button: to customise beverage quantity
B8. Mode selector dial:
• Espresso
• Americano
• Coee
• Descaling
B9. Descale light
B10. Steam ready light
B11. No bean container light
B12. Energy saving light
B13. Cleaning light (see“8.1 Cleaning of the coee outlet”)
B14. Bean container empty
B15. No water light
B16. Tamping light
B17. Pressure gauge
1.3 Description of accessories - C
C1. Portalter
C2. 1-cup coee lter
C3. 2-cups coee lter
C4. “Water hardness test“ indicator paper
C5. Descaler
C6. Power cord
C7. Tube brush
C8. Coee outlet cleaning disk accessory
C9. Milk pitcher
C10. Cleaning needle for steam nozzle
1.4 Recommended optional cleaning accessories
Visit Delonghi.com for more information.
Cleaning tab
(see“8.1 Cleaning of the coee outlet”)
Cleaner
EAN: 8004399333307

6
2. PREPARING YOUR MACHINE FOR FIRST USE
REMOVE
PROTECTION FILM
BEFORE USE
MAX
3. Insert the drip tray (A10)
complete with cup grill
(A8) and (A9).
1. Remove stickers and pack-
ing materials.
2. Wash and dry all acces-
sories (including water
tank) with warm water
and washing-up liquid .
4. Remove the water tank
(A14) and ll with fresh
clean water, taking care
not to exceed the MAX
level.
5. Insert the Bean container
(A2) in the coee grinder.
6. The container is correctly
inserted when the arrow
is lined up with the
symbol and you hear a
“click”.
7. Plug the power cord con-
nector (C6) into the sock-
et (A16) at the back of
the machine, then plug
into the mains socket.
8. Make sure the main
switch (A17) at the
back of the machine
is pressed and in the I
position.
REMOVE
PROTECTION FILM
BEFORE USE
MAX
REMOVE
PROTECTION FILM
BEFORE USE
MAX
9. Place a container with a
minimum capacity of 100
ml under the hot water
spout (A5).
10. Press (B6) to rinse. 11. Insert coee lter ((C2)
or (C3)) in the portalter
(C1).
12. Attach the lter holder
lter to the machine. To
attach correctly, align the
lter holder handle with
“INSERT”, then turn the
handle to the right until
it is aligned in the “CLOSE”
position.
1
5
9
2
6
10
3
7
11
4
8
12

7
REMOVE
PROTECTION FILM
BEFORE USE
MAX
PREPARING YOUR MACHINE FOR FIRST USE
13. Place a container under
the portalter and froth-
ing wand and press OK
(B5). Repeat 2 times to
rinse the coee circuit.
14. Open the steam dial for a
few seconds. For optimal
steam performance we
recommend you repeat
this action 3 or 4 times.
This is to purge the steam
circuit before frothing or
steaming your milk.
Step 1-grinding
Step 3-brewing
Step 2-tamping
3. COFFEE DELIVERY
Step 1-grinding
Step 3-brewing
Step 2-tamping
1. Add beans to hopper
(A2). Fresh is best; ll in
just with the quantity
you need.
2. The factory setting is 5
(medium grinding). If you
are not satised, adjust
the level according to
your personal taste and
the type of coee (do it
while grinding).
3. Select single or double
dose lter and place in
the portalter (C1). If you
are using the double lter,
press the X2 button (this
will double the volume of
the espresso shot as well).
4. Set the dose level by
adjusting the dial (B2)
starting from the min.
position.
Whenusing thecoeegrinder fortherst time, leavethe
knob to Min position. At the beginning, it is normal for
a few attempts to be needed before nding the correct
grinding level and quantity. We recommend starting
by using the default values, then if necessary changing
them according to the tips in section“3.1 Adjust dose”.
5. Attach portalter.
Once locked into place, grind-
ing will start.
4
1 2 3
5

8
Step 1-grinding
Step 3-brewing
Step 2-tamping
1. After grinding, pull the
lever (A20) down fully
(do not remove portal-
ter). For a perfect result,
you can do it twice.
2. Keep the lever down
while removing the por-
talter. Once it is done,
place back the lever in its
original position.
3. Check the dose (see “3.2
The perfect dose”) and
attach the portalter
(C1) to the brewing unit
(A18).
3.2 The perfect dose
• The coee lters have a mark inside to identify the level for
perfect dose.
• Ensure the coee is at the recommended dosage level after
tamping. You may need to adjust the dosage dial more
times before reaching the perfect dose.
• If your coee is over or under extracted and the dose is
within the perfect dose range, adjust the grinder settings
ner or coarser (see Step 1 - grinding).
Over extracted coee (pouring too slowly) needs coarser
grind
Under extracted coee (pouring too fast) needs ner grind.
• Barista tip: Pull the lter holder out while the tamper is
still down for polished nish of coee.
• Using pre-ground coee:
- add the pre-ground coee in the lter
- turn the dial to ;
- attach the lter holder to the machine;
- pull the lever down.
• Please note: If any residual ground coee remains after
tamping, it will not impact the quality of the extraction.
1 2 3
3.1 Adjust dose
Each variety of coee beans can behave dierently during grin-
ding and this is the reason why setting the dose at the beginning
might require extra care.
With this illustration we give you some indications on how to
regulate the dose. Please note these suggested setting ranges,
based on the roasting level, are certainly a good starting point,
but they might slightly vary depending on specic composition
of your coee beans.
1. Set the dose starting from the minimum position.
2. Look at which roasting type your coee is and based on
that, turn the knob slowly, referencing the ranges.
EXTRA
GRINDING
ADJUSTMENT
EXTRA LIGHT
LIGHT
MEDIUM
DARK
MEDIUM - DARK EXTRA DARK
Perfect
dose

9
COFFEE DELIVERY
Step 1-grinding
Step 3-brewing
Step 2-tamping
1. Select the tempera-
ture (see “3.3 Focus on
temperature”).
2. Select your beverage.
1 2
3. Press OK to start brew-
ing (preinfusion and
infusion). Coee delivery
stops automatically.
3.3 Focus on temperature
The water temperature is precisely controlled throughout the entire brewing process to ensure the ideal temperature stability for the
extraction. La Specialista Prestigio oers up to 3 infusion temperature*proles to select, correspondent to a range of temperatures
between 92°C and 96°C.
Coee bean varieties as well as roasting colours require their own specic temperature setting for the best extraction: Robusta coee
beans prefer lower temperature; Arabica prefers higher temperature.The same is applicable to beans with a darker roasting colour or
to freshly-roasted beans than those degassed over time.
Temperature level MIN MED MAX
Corresponding light
Coee Beans Roasting Range DARK MEDIUM to DARK LIGHT to MEDIUM
* This temperature refers to the water inside the thermoblock. This diers from the temperature of the beverage in the cup or the
temperature measured when the beverage comes out from the portalter spouts.

10
5°C
Manual
frothing
4. MAKING MILK BEVERAGES
1. Fill the milk pitcher (C9)
with fresh cold milk.
Milk will up to triple in
volume.
2. Turn the steam wand (A6)
on briey to purge con-
densation. Make sure the
wand is pointing away
from you.
3. To make the froth, put the
nozzle on the surface of
the milk and air will catch
by the mixing of milk and
steam.
5°C
Manual
frothing
4. Keep the steam nozzle just
on the surface, careful not
to make big bubbles by
letting too much air in.
5. Insert the steam nozzle
just under the milk: this
create a vortex. Once the
desired temperature is
reached turn the steam
knob o and wait till
steam stops completely
before removing jug.
Cleaning the steam wand
1. After every use, remove
with a soft damp cloth
any milk residues from the
steam wand. For perfect
cleaning, we recommend
Eco MultiClean: it ensures
hygiene by removing milk
proteins and fats and can
beused to cleanthe whole
machine.
2. Use the steam for a deeper
cleaning.
3. Wait that the steam wand
cool down and open the 3
holes of the nozzle with
the Cleaning tool to main-
tain the better usability of
the steam wand.
1 2 3
4 5
Barista tips:
• Fresh is best : Be sure to use fresh cold milk every time.
• For best results, store the milk pitcher in the refrigerator.
• Whole milk is recommended for best results. Dairy and Non Dairy alternatives will vary in ease of texturing depending
on type.
• After foaming milk, eliminate unwanted bubbles by swirling the pitcher.

11
5. EXPLANATION OF LIGHTS
LIGHTS EXPLANATION OF LIGHTS OPERATION
All the lights ash briey Turning the machine on Self-diagnosis
on
The appliance is being turned on for the rst
time and the water circuit must be lled
Proceed as described in section “2. Preparing your
machine for rst use”.
(white) + on
( selected temperature is on)
The machine is ready to delivery Prepare the machine and proceed with delivery
on Energy saving is enabled If you want to disable the function, see section “6.
Menù settings”
on The beans container (A2) is empty Fill the beans container
ashing You are trying to grind coee but the
beans container (A2) is empty
Fill the beans container
ashes briey at
regular intervals
The dial (B2) has been turned to the
maximum adjustment possible
When not enough coee is ground to reach the cor-
rect quantity, select the new grinding range as de-
scribed in section“6. Menù settings”.
on Insucient water in tank (A14) or
water tank not inserted correctly
Fill the tank or extract the tank and put it back
correctly
ashing
You are trying to deliver a beverage but
water tank is empty
Fill the tank
The grinding is too ne and the coee is
delivered too slowly or not at all
Extract the lter holder and repeat the operations to
make the coee, bearing in mind the indications in sec-
tion“3.1 Adjust dose”and table“3.2The perfect dose”.
The lter (C2) or (C3) is blocked Clean as described in section “8. Cleaning and
maintenance”.
The tank (A14) has been inserted incor-
rectly and the valves on the bottom are
not open
Press the tank down lightly to open the valves on the
bottom
Scale in the water circuit Descale as described in section“10. Descaling”
on (If Energy saving is not activated) The
appliance is on and ready for use
The appliance is at the right temperature to deliver
steam.To deliver steam, turn the steam dial (A4)
ashing
The appliance is on and energy saving
is enabled.The steam dial (A4) is in the
steam delivery position
The light ashes to indicate that the appliance is pre-
paring to deliver steam. Delivery begins as soon as
the appliance is at temperature
The appliance is heating up to be ready
for use
The appliance is at temperature when the light re-
mains on steadily
The appliance is delivering steam
…→

12
LIGHTS EXPLANATION OF LIGHTS OPERATION
on
The bean container (A2) is not inserted Insert bean container or check that is completely locked.
The container is correctly inserted when the arrow is
lined up with the symbol and you hear a“click”.
ashing
The ness of the grind regulation is in-
correct (or out of correct range)
Move the selector within the 8 levels from coarse to
ne, keeping in mind to:
• Always adjust the coee mill during the grinding
• Adjust one grinding level at a time and make at
least 5 coees before adjusting again
OUT of correct
range
Correct
range
on
Presser lever (A20) is not in the correct
position
Turn the lever back in place.
ashing
Pressing is needed The coee has just been ground and the lter holder
is attached to the coee mill
The portalter (C1) has been detached
from the coee mill without pressing
Detach the portalter and press the coee as de-
scribed in section “3.2 The perfect dose” “add the
preground coee in the lter”
The portalter has been detached be-
fore grinding has ended or pressing has
been performed too quickly
Repeat grinding
The slide of coee grinder is clogged Clean as described in section “8.5 Cleaning the
“Smart tamping station”” and section “11. Trouble-
shooting”in correspondence to the picture.
The burrs are blocked by foreign matter Remove the foreign matter and clean the burrs as de-
scribed in section“8.3 Cleaning the burr”.
on (red) Descaling must be performed
Descale the appliance as described in section“10. Descaling”
ashing (red) +
ashing (orange)
Descaling is underway Complete the operation as described in section “10.
Descaling”: the light comes white when the rinsing
cycle of descaling is underway
on (red) + on
(white)
The rinsing cycle of descaling must be
performed
…→

13
LIGHTS EXPLANATION OF LIGHTS OPERATION
ashing (red) +
ashing (white)
The rinsing cycle of descaling is
underway
on (orange) Cleaning of the coee outlet must be
performed
See section“8.1 Cleaning of the coee outlet”
ashing (orange)
Cleaningof the coee outlet is underway
All the lights ash General alarm Contact Customer Services
Press button to set:
➡ON
➡OFF
Energy saving
Press button to set:
➡9 minutes
➡ 1,5 hours
➡ 3 hours
Auto o
Press button to set:
➡ 1st range
➡2nd range
Extra grinding
adjustment
Press button to set:
➡soft
➡ medium
➡ hard
Waterhardness
Keep pressed
button
for 5 seconds,
until the correspon-
ding light starts
ashing
Default values
Press the ON/Standby button to conrm.
Save new settings:
Select the setting
6. MENÙ SETTINGS
Press both buttons for 5 seconds
to enter setting menu
Enter the setting menu
Turn the knob to select the drink
light corresponding to the fun-
ction to set
Select the setting

14
7. CUSTOMISING THE QUANTITY OF COFFEE BEVERAGES WITH THE BUTTON (B7)
1. Prepare the appliance to
deliver the beverage you
want to make. Prepare the
coee dose and attach the
portalter to the coee
outlet.
2. Turn the dial (B8) to
select the drink to be
programmed.
3. Press the button
(B7): the light corre-
sponding to the OK
button (B5) comes on
steadily and the light cor-
responding to the
button ashes.
4. Press the OK button (B5)
to start delivering the
beverage. The lights cor-
responding to the OK and
buttons ash.
5. When you have reached
the desired quantity of
the beverage, press the OK
button again. If the recipe
includes another ingre-
dient, it starts delivery:
when you have reached
the desired quantity, press
the OK button again.
6. Press the button to
save the new setting. The
appliance is ready for use
again and the but-
ton remains on.
If you do not want to save the
new setting, press any other
button.
Please note:
• You can programme coee beverages quantities, but not
steam and hot water as those are manual functions.
• Programming changes the quantity of the beverages, but
not the amount of coee ground.
• “X2” beverages can be programmed separately.
• To reset the default beverage quantities, press and hold
the button until it goes o. The selected beverage is
reset to the default values.
1
5
2
6
3 4
Coee
Recipe
Default
quantity
Programmable quantity
1.83  oz
/ 35 ml
from 0.84 to 3.04  oz /
from 25 to 90 ml
X2 2.37  oz
/ 70 ml
from 1.69 to 6.08  oz /
from 50 to 180 ml
2.70  oz
/ 80 ml
from 1.69 to 6.08  oz /
from 50 to 120 cc
X2 5.41  oz
/ 160 ml
from 4.06 to 8.12  oz /
from 120 to 240 ml
4.06  oz
/ 120 ml
• espresso: from 0.84 to 2.02  0z/
from 25 to 60 ml
• water: from 0.84 to 4.06  oz /
from 25 to 120 ml
X2 8.12  oz
/ 240 ml
• espresso: from 1.69 to 6.08  oz/
from 50-120 ml
• water: from 1.69 to 8.12  oz/
from 50 to 240 ml

15
8. CLEANING AND MAINTENANCE
Important!
• Do not use solvents, abrasive detergents or alcohol to clean the coee machine.
• Do not use metal objects to remove encrustations or coee deposits as they could scratch metal or plastic surfaces.
• If the appliance is not used for more than a week, before using it again, we recommend you perform a rinse cycle.
Danger!
• While cleaning, never immerse the coee maker in water. It is an electrical appliance.
• Before cleaning the outside of the appliance, turn it o, unplug from the mains socket and allow to cool.
✕✓✕ ✕ ✕
✓✕ ✕ ✕ ✕
✓✕ ✕ ✓✕
✕✓ ✓ ✓ ✓
✕✓ ✓ ✕✓
(A7)+(A8)+ (A9)
8.1 Cleaning of the coee outlet
When the light comes on (orange) (B13), you have to proceed cleaning the coee circuit. To run the cleaning, you have to pur-
chase dedicated cleaning tabs for coee makers. For more info, please visit Delonghi.com.
MAX
1. Insert the 1-cup coee
lter (C2) in the portal-
ter (C1);
2. Put on the coee lter
the special disk acces-
sory (C8) and press it to
the bottom;
3. Put on the accessory the
cleaning tab;
4. Attach the portalter to
the coee outlet (A18);
1 2 3 4

16
Cleaning of the coee outlet
MAX
5. Fill the water tank (A14).
Make sure the drip tray
(A10) is empty.
6. Keep pressed the
button, until the
light starts blinking
(orange). After few min-
utes the cleaning stops
automatically;
7. Remove the portalter and the cleaning disk accessory;
8. Wash the portalter and the lter under tap water;
9. Insert the portalter again and make a rinse by pressing
the OK button: we suggest to put a container under the
portalter;
10. Remove and empty the drip tray.
Please note:
This procedure can start by pressing the button (B6)) for
some seconds. To delete this option, press the same button for
10 seconds.
8.2 Cleaning the beans container housing
1. Make sure the beans
container (A2) is empty.
If necessary, operate the
coee mill without beans
to empty it:
2. Release the beans con-
tainer by turning it an-
ticlockwise and extract
from the appliance;
3. Remove coee residues
using a vacuum cleaner;
4. Clean the beans contain-
er housing with a damp
cloth and dry;
5. Put the container back
inserting it in the coee
mill. The container is
correctly inserted when
the arrow ▲is lined up
with the symbol and
you hear a“click”.
1
5
1
2
2
3 4

17
8.3 Cleaning the burr
When cleaning the beans container, clean the container housing and upper burr with a damp cloth. The burr can be removed and replaced
by an authorised customer services centre.
You may also need to remove the burr if it becomes blocked withforeign matter. If this occurs, remove the beans container and clean
as follows:
1. Attach the portalter and
operate the mill without
beans to free the coee
guide;
2. Turn the appliance o;
3. Turn the grinding selector
anticlockwise as far as it
will go to the “REMOVE”
position;
4. Extract the upper burr,
gripping it by the handle;
5. Clean the burr with a
brush (not included)
and remove the coee
residues using a vacuum
cleaner;
6. Put the upper burr back
in place;
7. Turn the selector to select
the desired grinding level.
Make sure the burr is inser-
ted correctly by pulling it by
the handle. If it is correctly
inserted, it will not move.
8.4 Replacing the burrs
When the quantity of coee becomes even less, contact a customer services centre to have the burrs replaced, then adjust the mill
again as follows entering the setting menu (“6. Menù settings”) and selecting the rst range of the“Extra grinding adjustment”.
Then turn the ground coee quantity dial (B2) to minimum position and set the dose like a rst use (see“3.2The perfect dose”).
8.5 Cleaning the“Smart tamping station”
1. Clean the attachment area with a brush;
2. Pull the lever (A20) as far as it will go and
clean the presser cylinder with a brush. Then
release the lever.
3. Use the tube brush (C7) to clean the coee
funnel.
1 2 3
1
5
2
6
3
7
4

18
9. WATER HARDNESS
9.1 Water hardness
The descale light (B9) comes on after a period of time established according to water hardness. The machine can also be pro-
grammed according to the actual hardness of the water supply in the various regions, in which case descaling may be required less
frequently.
1. Remove the“TOTAL HARD-
NESS TEST” indicator paper
(C4) from its pack.
2. Immerse the paper com-
pletely in a glass of water
for one second.
3. Remove the paper from the
water and shake lightly.
After about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to one
level.
Total Hardness Test result Button Level
1
soft water
2
medium
water
3
hard or
very hard
water
4. Set the appliance as indi-
cated in section“6. Menù
settings”.

19
A
B
A
B
10. DESCALING
1. IF PRESENT, REMOVE
THE WATER SOFTENER
DEVICE. Pour the des-
caler into the tank up to
the level Amarked
inside the tank (equal to
one 100ml packet).
2. A dd water (1 liter) up
to t he level B.
Then put the water tank back in
the appliance.
3. Turn the mode selector
dial (B8) to :the
light begins to blink:
and the OK light turns to
orange.
4. Make sure the portalter is
not attached and position a
recipient under the coee
outlet, hot water spout and
steam wand.
5. Press the OK (B5) but-
ton: descaling starts.
Please note
• Before use, read the instructions and the labelling on the descaler pack.
• It is important to use De’Longhi descaler only. Using unsuitable descaler and/or performing descaling incorrectly may result
in faults not covered by the manufacturer’s guarantee.
• Descaler could damage delicate surfaces. If the product is accidentally spilt, dry immediately.
4
1
5
2 3
RED
40
Minutes
De’LonghiAppliances s.r.l.
ViaL. Seitz, 47 31100 Treviso - ITALY
Tel.[phone]
5413218631/04.15
Decalcificanteper macchine da caffè
Descalerfor coffee machines
Détartrantpour machines à café
Entkalkerfür Kaffeemaschinen 2 L
6. The descale programme starts and the descaler liquid
comes out of the steam wand and coee outlet.The des-
cale programme removes limescale deposits from inside
the appliance by automatically performing a series of
rinses and pauses until the tank is empty.
Delive ry stops and th e OK light turns to white. This indicates
that it is necessary to proceed with rinsing: see next page.
When the light (B9) comes
on, it is time to proceed descal-
ing the machine. The descaling
cycle can be run in any moment.
Please note
• In case you start the descaling
cycle by mistake, you can press
the OK button for 10 seconds; the
rinsing cycle can not be stopped
(from step 9).