DeLonghi DEF905GEG User manual

DE’LONGHI
COOKING
INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
DEF905GEG
DUAL FUEL COOKER
distributed by
DeLonghi Australia Pty Ltd
DeLonghi New Zealand Ltd

2

3
Dear Customer,
Thank you for having purchased and given your preferen-
ce to our product.
The safety precautions and recommendations reported
below are for your own safety and that of others. They will
also provide a means by which to make full use of the fea-
tures offered by your appliance.
Please keep this booklet in a safe place. It may be useful
in future, either to yourself or to others in the event that
doubts should arise relating to its operation.
This appliance must be used only for the task it has
explicitly been designed for, that is for cooking fo-
odstuffs. Any other form of usage is to be considered
as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the
event of damage caused by improper, incorrect or illo-
gical use of the appliance or be faulty installation.
PRODUCT LABEL
This appliance has been designed and constructed in accordance with the following codes
and specications:
AS 4551 Approval Requirements for Domestic Gas cooking appliances
AS/NZS 60335.1 General Requirements for Domestic electrical appliances
AS/NZS 60335.2.6 Particular Requirements for Domestic electrical cooking appliances
AS/NZS CISPR 14.1 Electromagnetic Compatibility Requirements.

4
IMPORTANT SAFETYPRECAUTIONSAND RECOMMENDATIONS
IMPORTANT: This appliance is designed and manufactured
solely for the cooking of domestic (household) food and is
not suitable for any non domestic application and therefore
should not be used in a commercial environment.
The appliance guarantee will be void if the appliance is used
within a non domestic environment i.e. a semi commercial,
commercial or communal environment.
Read the instructions carefully before installing and using
the appliance.
■After having unpacked the appliance, check to ensure that it is not
damaged and that the oven door closes correctly.
In case of doubt, do not use it and consult your supplier or a
professionally qualied technician.
■Packing elements (i.e. plastic bags, polystyrene foam, nails,
packing straps, etc.) should not be left around within easy reach of
children, as these may cause serious injuries.
■ Some appliances are supplied with a protective lm on steel and
aluminium parts. This lm must be removed before using the
appliance.
■ IMPORTANT: The use of suitable protective clothing/gloves is
recommended when handling or cleaning this appliance.
■Do not attempt to modify the technical characteristics of the
applianceasthismaybecomedangeroustouse.Themanufacturer
declines all responsibility for any inconvenience resulting from the
inobservance of this condition.
■ CAUTION: this appIiance must only be installed in a permanently
ventilated room in compliance with the applicable regulations.
■Do not operate your appliance by means of an external timer or
separate remote-control system.
■Do not carry out cleaning or maintenance operations on the
appliance without having previously disconnected it from the
electric power supply.
■ WARNING: Ensure that the appliance is switched off before
replacing the oven lamp to avoid the possibility of electric shock.

5
■Do not use a steam cleaner because the moisture can get into the
appliance thus make it unsafe.
■Do not touch the appliance with wet or damp hands (or feet).
■Do not use the appliance whilst in barefoot.
■If you should decide not to use this appliance any longer (or
decide to substitute another model), before disposing of it, it is
recommendedthatitbemadeinoperativeinanappropriatemanner
in accordance to health and environmental protection regulations,
ensuring in particular that all potentially hazardous parts be made
harmless, especially in relation to children who could play with
unused appliances.
■The various components of the appliance are recyclable. Dispose
of them in accordance with the regulations in force in your country.
If the appliance is to be scrapped, remove the power cord.
■After use, ensure that the knobs are in the off position.
■Children less than 8 years of age shall be kept away unless
continuously supervised.
■This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
■The manufacturer declines all liability for injury to persons or
damage to property caused by incorrect or improper use of the
appliance.
■ WARNING: During use the appliance and its accessible parts
become hot; they remain hot for some time after use.
– Care should be taken to avoid touching heating elements (on
the hob and inside the oven).
– The door is hot, use the handle.
– To avoid burns and scalds, young children should be kept away.
■Make sure that electrical cables connecting other appliances in the
proximity of the cooker cannot come into contact with the hob or
become entrapped in the oven door.

6
■ WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in re. NEVER try to extinguish a re
with water, but switch off the appliance and then cover ame e.g.
with a lid or a re blanket.
■ WARNING: Danger of re: do not store items on the cooking
surfaces.
■DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE COMPARTMENT OR NEAR THIS
APPLIANCE.
■ DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.
■DO NOT MODIFY THIS APPLIANCE.
■WHERETHISAPPLIANCEIS INSTALLEDINMARINECRAFTOR
IN CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER.
■ WARNING: When correctly installed, your product meets all safety
requirements laid down for this type of product category. However
special care should be taken around the rear or the underneath of
the appliance as these areas are not designed or intended to be
touched and may contain sharp or rough edges, that may cause
injury.
■ FIRST USE OF THE OVEN - it is advised to follow these instructions:
– Furnish the interior of the oven as described in the chapter “USE
AND CARE”.
– Switch on the empty oven on max to eliminate grease from the
heating elements.
– Disconnect the appliance from the electrical power supply, let
the oven cool down and clean the interior of the oven with a
cloth soaked in water and neutral detergent; then dry carefully.
■ CAUTION: Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can scratch the
surface, which may result in shattering of the glass.
■Do not line the oven walls with aluminium foil. Do not place baking
trays or the drip tray on the base of the oven chamber.
■ FIRE RISK! Do not store ammable material in the oven or in the
storage compartment.
■Always use oven gloves when removing the shelves and food trays

7
from the oven whilst hot.
■Do not hang towels, dishcloths or other items on the appliance or
its handle – as this could be a re hazard.
■Clean the oven regularly and do not allow fat or oils to build up in
the oven base or tray. Remove spillages as soon as they occur.
■Do not stand on the cooker or on the open oven door.
■Always stand back from the appliance when opening the oven door
to allow steam and hot air to escape before removing the food.
■ SAFE FOOD HANDLING: Leave food in the oven for as short a time
as possible before and after cooking.This is to avoid contamination
by organisms which may cause food poisoning. Take particular
care during warmer weather.
■ WARNING: Take care NOT to lift the cooker by the door handle.

8
MOVING THE COOKER
WARNING:
When raising cooker to upright
position always ensure two
people carry out this manoeuvre
to prevent damage to the
appliance and adjustable feet
(g. 1).
WARNING - Be carefull:
Do not lift the cooker by the
door handle when raising to the
upright position (g. 2).
WARNING:
When moving cooker to its nal
position DO NOT DRAG (g. 3).
Lift feet clear of oor (g. 1).
Figure 1
Figure 3
Figure 2

9
INSTALLATION
CAUTION:
■This appliance must be installed according to AS/NZS 5601.1 (latest edition).
■This appliance must be installed in accordance with these installation instructions.
■This appliance shall only be serviced by authorized personnel.
■This appliance is to be installed only by an authorised person in compliance
with the current electrical regulations and in observation of the instructions
supplied by the manufacturer.
Failure to comply with this condition will render the guarantee invalid.
■Incorrect installation, for which the manufacturer accepts no responsibility, may
cause personal injury of damage.
■Always disconnect the appliance from mains power supply before carrying out
any maintenance operations or repairs.
■In the room where the cooker is installed, there must be enough air to allow the
gas to burn correctly, according to the current local regulations.
ELECTRICAL REQUIREMENTS
■The appliance must be connected to the mains checking that the voltage corresponds
to the value given in the rating plate and that the electrical cable sections can withstand
the load specied on the plate.
■This cooker must be connected to a suitable double pole control unit adjacent to the
cooker. No diversity can be applied to this control unit.
■Asuitabledisconnectionswitch mustbeincorporated inthepermanent wiring,mounted
and positioned to comply with the local wiring rules and regulations. The switch must
be of an approved type installed in the xed wiring and provide a 3 mm air gap contact
separation in all poles in accordance with the local wiring rules.
InAustralia and New Zealand, a switch of the approved type with a 3 mm air gap must
be installed in the active (phase) conductor of the xed wiring.
■Once the appliance has been installed, the switch must always be accessible.
■To connect the cooker to the mains, do not use adapters, reducers or branching
devices as they can cause overheating and burning.
■The power supply cable must not touch the hot parts and must be positioned so that it
does not exceed 50°C above ambient.
■If the supply cord is damaged it must be replaced by the manufacturer or it’s Service
Agent or a similarly qualied person in order to avoid a hazard.
WARNING: This cooker must be connected to electrical supply using V105 insulated
cable (size: 3 x 1.5 mm2).
N.B. The connection of the appliance to earth is mandatory.
If the installation requires alterations to the domestic electrical system call a qualied
electrician. He should also check that the domestic electrical system is suitable for the
power drawn by the appliance.
Appliance power rating: 220-240 V~ 50/60 Hz 2250 W (9.78 A)
Replacing the power cord must be done by a qualied electrician in accordance with
the instructions supplied by the manufacturer and in compliance with established
electrical regulations.

10
CLEARANCES
Installation clearances and protection of combustible surfaces shall comply with the current
local regulations eg. AS/NZS5601.1 (latest edition) Gas Installations code.
Installation shall comply with the dimension in g. 4a bearing in mind that.
Overhead Clearances
In no case shall the clearances between the highest part of the cooker be less than
650 mm or for an overhead exhaust fan 750 mm. AII other downward facing combustible
surfaces less than 650 mm above the cooker surface shall be protected for the full width
of the cooking surface in accordance with the standards noted above. In no case shall the
clearance be less than 450 mm.
Rear and Side Clearances
Where the dimensions from the periphery of the nearest burner to any vertical combustible
surfaceis less than200mm the surfaceshall be protectedin accordance with thestandards
to a height of not less than 150 mm above the cooking surface for the full width or depth of
the cooking surface.
Wherethedimensionsfromtheperipheryofthenearestburnertoanyhorizontalcombustible
surface is less than 200 mm, the horizontal surface shall be greater than 10 mm below the
surface of the hob, or the horizontal surface requirement above.
Protection of combustible surfaces
The standards above specify that where required protection shall ensure that the surface
temperature of the combustible surface does not exceed 65 °C above room temperature.
Do not install the cooker near ammable materials (eg curtains)
If the cooker is located on a pedestal it is necessary to provide safety measures to
prevent falling out.
750 mm
500 mm
50 mm
A
U
T
O
450 mm
Figure 4a
Cooker overall dimensions [mm]
■ height: min 900 - max 925
■ width: 900
■ depth: 600

11
FITTING THE ADJUSTABLE FEET
The adjustable feet must be tted to the base of the cooker before use (gs. 5, 6).
Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for
the tting of the feet.
Fit the no. 4 (four) legs by screwing them tight into the support base as shown in gure 6.
LEVELLING THE COOKER
The cooker may be levelled by screwing the lower ends of the feet IN or OUT (g. 7).
Figure 6 Figure 7Figure 5
max 290 mm
Dotted line
showing the
position of the
cooker when
installed
Area for GAS
and ELECTRIC
connection
GAS AND ELECTRIC CONNECTION
Figure 4b

12
C
B
A
FIXING THE BACKGUARD
Before installing the cooker, assemble the backguard “C” (g. 8).
■The backguard “C” can be found packed at the rear of the cooker.
■ Before assembling remove any protective lm/adhesive tape.
■Remove the two spacers “A” and the screw “B” from the rear of the cooktop.
■ Assemble the backguard as shown in g. 8 and x it by screwing the central screw “B”
and the spacers “A”.
Figure 8

13
ANTI-TILT BRACKET
Important!
To restrain the appliance and prevent it
tipping accidentally, t a bracket to its
rear to x it securely to the wall. Make
sure you also t the supplied lock pin to
the anti-tilt bracket.
To t the anti-tilt bracket:
1. After you have located where the
cooker is to be positioned, mark on the
wall the place where the two screws
of the anti-tilt bracket have to be tted.
Please follow the indications given in
g. 9.
2. Drill two 8 mm diameter holes in
the wall and insert the plastic plugs
supplied.
Important!
Before drilling the holes, check that
you will not damage any pipes or
electrical wires.
3. Loosely attach the anti-tilt bracket with
the two screws supplied.
4. Move the cooker to the wall and adjust
the height of the anti-tilt bracket so
that it can engage in the slot on the
cooker’s back, as shown in g. 9.
5. Tighten the screws attaching the anti-
tilt bracket.
6. Push the cooker against the wall so
that the anti-tilt bracket is fully inserted
in the slot on the cooker’s back.
7. Access the bracket and t the lock pin:
■ Open the pivoting panel (g. 10).
■Fit the lock pin through the bracket, as
shown (g. 11).
■Close the pivoting panel.
min 220
max 245
450 450
0
+ 25
900 mm
min 220
max 245
(depending on feet adjustment)
450 450
0
+ 25
900 mm
1
2
Pivoting
panel
Lock pin
correctly
fitted
Lock pin
Slot on the
cooker’s back
Cooker’s
back
Anti-tilt bracket
attached on the
rear wall
min 220
max 245
(depending on feet adjustment)
450 450
0
+ 25
900 mm
1
2
Pivoting
panel
Lock pin
correctly
fitted
Lock pin
Slot on the
cooker’s back
Cooker’s
back
Anti-tilt bracket
attached on the
rear wall
Figure 9
Figure 10
Figure 11

14
GAS SUPPLY
■The connection must be performed by an authorised person according to the relevant
standards.
■Before connecting the appliance to the gas main, mount the brass conical adaptor
onto the gas inlet pipe, upon which the gasket has been placed (gs. 12a - 12b).
Conical adaptor and gasket are supplied with the appliance (packed with conversion
kit for use with Natural gas or ULPG).
■This appliance is suitable for use with Natural Gas or ULPG (Check the “gas type”
sticker attached to the appliance).
■For Natural Gas models the gas supply is connected to the pressure regulator which
is supplied with the appliance (g. 12b). Adjust the regulator to obtain a test point
pressure of 1 kPa with the two semi-rapid (SR) burners operating at maximum.
■For ULPG models the gas supply is connected to the test point adaptor which is
supplied with the appliance (g. 12a) and ensure that the supply pressure is regulated
to 2.75 kPa.
■The connection must be made at the rear of appliance (left or right); the pipe does not
cross the cooker (g. 13).
■The inlet not used must be closed off with the cap and sealing gasket supplied.
■ IMPORTANT: Use two spanners to tighten or loosen the connecting pipe (g. 14).
INSTALLATION WITH A FLEXIBLE HOSE ASSEMBLY
■If this appliance has to be installed with a hose assembly, the installer shall refer to the
network operator or gas supplier for conrmation of the gas type, if in doubt.
■ When used with a exible hose, the connector on the wall should be between 450
mm to 500 mm from the oor and 200 mm to 300 mm from the left-hand side of the
appliance as viewed from the front. The hose connection on the appliance shall face
downwards.
■It is important that the hose does not come in contact with the metal of the appliance
and is secured as per appropriate gas installation codes.
 A chain 80% of the length of the exible gas hose must be used to prevent stress
being applied to the hose. The chain should be attached securely to the product where
shown, and on the wall.
■ Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certied.
The thread connection shall be Rp ½” (ISO 7-1) male.
■IMPORTANT WARNING: After connection the installer must check that the hose
is not kinked, subjected to abrasion or permanently deformed.
The installer must check also that the hose is not near (or in contact) with any
hot surfaces.
■The hose assembly shall be as short as practicable and comply with relevant
AS5601 / NZS5261 requirements.

15
Gas connection for
ULPG
Gas inlet pipe
Nipple
Gasket
Brass conical adaptor
(Thread tight: use
suitable seal)
Test point adaptor
Test
point
Gas connection for
NATURAL GAS
Gas inlet pipe
Nipple
Gasket
Brass conical adaptor
(Thread tight: use
suitable seal)
Gas regulator
Test
point
Figure 12a Figure 12b
Plug
Chain
security
hole
Figure 14
Figure 13

16
LEAK-TESTING AND FLAME-TESTING THE COOKER
1. After connecting the gas supply, check the piping and connections for leaks
using a soap and water solution. The presence of bubbles indicates a leak,
tighten or replace connections as appropriate.
Warning: Do not use any naked ame to check for leaks.
2. Adjust the test point pressure or supply pressure to the value which is appropriate for
the gas type.
3. The operation of the appliance must be tested when installation is completed.
■Turn on the appliance gas controls and light each burner individually and in
combination. Check for a well dened blue ame without any yellow tipping.
– Cooktop burners: if any abnormality is evident then check that the burner cap is
located properly and the injector nipple is aligned correctly.
– Oven burner: if any abnormality is evident then check that the burner is located
properly and the injector nipple is aligned correctly.
■Check the minimum burner setting by quickly rotating the gas control knob from the
maximum to the minimum position, the ame must not go out.
If adjustment is required carry out the “MINIMUM BURNER SETTING
ADJUSTMENT” procedure described following.
4. If satisfacfory performance cannot be obtained, the installer shall check the installation
and notify the local gas supply authority for a gas supply problem, or if it is an appliance
problem, our Customer Service Centre should be called to obtain the nearest
authorized Delonghi Service Agent.
CONVERSIONPROCEDURE(TOCONVERT TONATURALGAS ORTOULPG)
REPLACING THE INJECTORS
This appliance is suitable for use with Natural gas or ULPG (check the “gas type” sticker
attached to the appliance). A label stating the type of gas used after replacing the injectors
must be attached at the rear of the appliance, in proximity of the gas inlet connection.
The nominal gas consumption and injector size details are provided in table at page 21.
To replace the injectors proceed as follows:
1. Cooktop burners
■Remove pan supports and burners from the cooktop.
■Using a spanner, remove the injectors “J” (gs. 15a, 15b) and replace them with
ones according to the gas type (see following table - page 21).
■Adjust the minimum burner setting (see “MINIMUM BURNER SETTING
ADJUSTMENT” procedure described following).
■The cooktop burners are designed so that regulation of primary air is not required.
2. Oven burner
■Lift and remove the lower panel inside the oven.
■Unscrew and remove the burner securing screw “A” (g. 16).
■Slacken screw “B” (g. 16).
■ Withdraw the burner in the manner shown in gure 17, and rest it inside the oven.
Take care not to damage the wire to the ignition electrode and the safety valve
probe.

17
■Using a 10 mm box spanner, unscrew the injector “U”(indicated by the arrow in
g. 17) and replace with a new injector selected in accordance with the “TABLE
FOR THE CHOICE OF THE INJECTORS” (see following table - page 21); then
replace the burner repeating the above steps in reverse order.
■Adjust the minimum burner setting (see “MINIMUM BURNER SETTING
ADJUSTMENT” procedure described following).
■The oven burner is designed so that regulation of primary air is not required.
JJ
Figure 15a Figure 15b
AB
U
Figure 16
Figure 17
Auxiliary, Semi-
rapid and Rapid
burners
Triple ring
burner

18
3. Afx to the rear of the appliance, in proximity of the gas inlet connections, the warning
label (supplied with the conversion kit) stating that the cooker has been converted for
use with ULPG / Natural gas.
IMPORTANT
■If the cooker is suitable for use with Natural gas and must be converted for use with
ULPG, before connecting to the gas mains remove the appliance gas regulator and
replace with test point adaptor (see gs. 12a - 12b).
■If the cooker is suitable for use with ULPG and must be converted for use with Natural
gas, before connecting to the gas mains remove the appliance test point adaptor and
replace with gas regulator (see gs. 12a - 12b).
NOTE: Gas regulator and test point adaptor are supplied with the appliance (packed with
conversion kit).
MINIMUM BURNER SETTING ADJUSTMENT
1. Cooktop burners
Check whether the ame spreads to all burner ports when the burner is lit with the gas
tap set to the minimum position. If some ports do not light, increase the minimum gas
rate setting.
Check whether the burner remains lit even when the gas tap is turned quickly from
the maximum to the minimum position. If the burner does not remain lit, increase the
minimum gas rate setting.
The procedure for adjusting the minimum gas rate setting is described below.
■Turn on the burner.
■Turn the tap to the MINIMUM position.
■Take off the knob.
■ Using a small at screwdriver turn the screw “F” to the correct regulation (g. 18).
Normally for ULPG, the regulation screw is tightened up.
2. Oven burner
In the minimum position the ame must have a length of about 4 mm and must remain
lit even with a brusque passage from the maximum position to that of minimum.
The ame adjustment is done in the following way:
■Turn on the oven burner by setting the thermostat knob on maximum position.
■Remove the knob and unscrew the by-pass screw “G” (g. 19) about three times
by passing a small at screwdriver (Ø 3 mm blade, 100 mm length) through the
panel opening.
■Re-mount the knob and let the oven heat up for about 10 minutes, then bring the
knob to position “1” (minimum) to operate the thermostat by-pass.
■After having removed the knob again and being very careful not to turn the
thermostat shaft, slowly screw the by-pass screws “G” (g. 19) until you obtain a
ame of 3-4 mm in height.
Normally for ULPG, the regulation screw is tightened up.

19
F
Figure 18
G
Figure 19

20
AIR RING ON OVEN BURNER
The air ring position is xed (fully open) for both Natural Gas and ULPG.
IMPORTANT: NEVER remove the xing rivet to modify the position of the air ring on the
oven burner (g. 20).
Rivet
Air ring
NO !
Figure 20