Delta Controls Red5-PLUS/EDGE-11 Series User manual

This guide describes how to install and configure a Red5-PLUS/EDGE-11xx controller. If you are using the
Proviso™ App, you will need an Android or iOS device with Proviso installed. Download the app for free from
Google Play or the App Store.
Installation
Follow all applicable electrical codes and regulations. Connect to a Class 2 power source only.
Wiring guidelines
The Red5 requires a 24 VDC/VAC
power supply.
• For power and I/O wiring, use 18
AWG 2-conductor copper wire.
• For network cabling, use Cat5e
or Cat6 cables.
Ground all devices according to Delta Controls
Wiring and Installation Guidelines.
Red5-EDGE-11xx models only: Up to 30
devices can be daisy chained using the ETH1 and
ETH2 ports as long as the distance between the
devices does not exceed 100 m (330 ft). A bypass
switch allows the devices to relay data in a
power failure scenario. However, the maximum
cable length is reduced by 15 m (50 ft) for each
bypassed device.
Mounting the Red5
1. The Red5 comes in a plastic enclosure that is designed to be installed onto a 35 mm × 7.5 mm top-hat DIN
rail.
2. Mount the Red5 in an appropriate location within packaged equipment or within another enclosure that
meets code requirements. Alternatively, the controller can be mounted with four screws (without using
DIN rail) via the 4 holes provided on the mounting clips.
Setup
Connecting to the Red5
There are three ways to connect to your Red5:
• Proviso App
• Embedded Web Server
• enteliWEB
January 2023
Red5-PLUS/EDGE-11xx
Quick Start Guide
© 2023 Delta Controls Inc.

The information in this document is subject to change without notice.
Proviso App
Bluetooth connection
To set up the Red5 using the Proviso app Bluetooth connection, you must have Bluetooth®and location
services enabled on your mobile device. For best performance, your device should support Bluetooth Low
Energy (BLE) version 5.0 or later.
1. Open the Proviso app and select Bluetooth for your connectivity method. Select a device to initiate a
connection. Nearby devices are listed by their Bluetooth MAC address.
2. A pairing request dialog displays. Select Pair.
3. Select Yes, Connect. You can now view device information in the Diagnostics tab.
To set up the Red5 using Proviso app NFC connection, you must have NFC enabled on your mobile device. This
can be done with the device powered up or down. For best performance, remove the case from your phone
and ensure you know the location of its NFC antenna.
NFC connection
1. Open the Proviso app and select NFC for your connectivity method. Position your device with its NFC
antenna over the NFC label on the Red5.
2. A Read Successful dialog displays. You can now view information in the Diagnostics tab.
3. From the Settings tab, configuration settings are available. See “Configuring the Red5” on page 3 for
more information on configuring your Red5.
4. Once you have configured your settings, select Apply settings to device.
5. Position your device over the Red5 as in step 1. A dialog displays confirming the settings are being
written. Do NOT remove or reposition your device until Write Successful displays.
6. Repeat step 1 and confirm your settings were applied as intended.
Embedded Web Server
The simplest way to access the embedded web server is to plug your laptop directly into one of the
controller’s Ethernet ports. This method is preferred.
To connect to the embedded web via a direct connection:
1. Make a note of the serial number listed on the back of the controller.
2. Connect your PC or laptop directly to one of the controller’s Ethernet ports. Make sure nothing else is
connected to the controller’s Ethernet ports (ETH1 and ETH2).
3. Enter https://169.254.178.50 in your browser’s address bar and proceed to the login page.
4. On the login page, under Username, enter Admin, and under Password, enter the controller’s serial
number without the slash (for example, 1234561234).
5. Click Login.
Note: Refer to the Installation Guide for more information on how to connect your controller using other methods.
enteliWEB
The simplest way to connect to the Red5 with enteliWEB is to plug your laptop directly into one of the
controller’s Ethernet ports and set up an Ethernet site connection in enteliWEB. For other connection types,
see the online help. A valid enteliWEB license is needed to access enteliWEB.
Note: See the online help for more information about setting up your device using enteliWEB.

Configuring the Red5
To configure your device, you must set up a network number and device address, after which you can
configure your network port settings. For more information, see KbA1654 andor the Device object topic in the
online help.
There are three ways to configure your Red5:
• Proviso App
• Embedded Web Server
• enteliWEB
Proviso App
1. To configure your Red5, go to Settings > Network. If you want to assign a static IP address, select , select
Static, enter the IP settings, then select Save. Otherwise, leave it as DHCP. The IP address must be unique
for each device.
2. Configure a network connection: IP, Ethernet, or Secure Connect.
3. Next to Security, select , enter a 6-digit PIN to secure BLE read/write access to the device, then select
Save.
4. Select Apply settings to device. After the settings are applied, the status shows Configured and a green
check mark appears next to each applied setting.
Embedded Web Server
Refer to the enteliWEB procedures for configuring your Red5 via the embedded web server.
enteliWEB
To configure your Red5 using enteliWEB, see the Configuration topic in the online help.
The information in this document is subject to change without notice.