Vimar EIKON 20593 User manual

Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com
20593 02 2110
EIKON
20593
ARKE'
19593
IDEA
16493
PLANA
14593
Connected actuator
The actuator is equipped with a relay output with a current meter and a front push button with
which to reset the load and perform configuration/reset. Its function is to protect against overcur-
rent by cutting off the load when the threshold value set via the View Wireless App is exceeded;
the load cut-off is signalled via the red flashing of the LED situated on the front of the device. Load
reactivation, aside from the front push button, can also be done via the View App. The View App
also makes it possible to view the instant power consumed.
TWO OPERATING MODES (ALTERNATIVE)
or
Download the View Wireless App from the stores onto the tablet/smartphone you
will be using for configuration.
When the device is powered for the rst conguration, we recommend you search for any
new rmware and perform the update.
Depending on the mode you select, you will need:
Gateway
art. 20597-19597-16497-14597
Zigbee Gateway
(Amazon Echo Plus, Echo Show or Echo
Studio)
Alexa App
View App
for management via smartphone/tablet
Alexa, Google Assistant, Siri and Homekit
voice assistants for possible voice oper-
ation
CONFIGURATION IN
1. Create your Installer account on MyVimar (on-line).
2. Wire all the devices in the system (2-way switches, actuators, thermostats, gateway, etc.).
3. Start the View Wireless App and log in with the credentials you just created.
4. Create the system and the environments.
5. Associate all the devices with the environments, except for the gateway (which should be
associated last).
To associate the actuator:
• Select “Add” ( ), choose the environment to place it and give it a name
• Select ; activate the Bluetooth connection on your tablet/smartphone and approach
the actuator
• Press the front push button and set the desired function
6. For every device, set the function, the parameters and any accessory devices (wired or radio
control and related function).
7. Transfer the configuration of the devices to the gateway and connect it to the Wi-Fi network.
8. Transfer the system to the Administrator user (who must have created his/her profile on
MyVimar).
For full details, see the View Wireless App manual that can be downloaded from the www.
vimar.com website.
CONFIGURATION IN
Follow the procedure above from points 1to 3.
Associate the relay module directly with Amazon Echo Plus, Echo Show or Echo Studio.
1) Press the front push button until the LED flashes. Download the Zigbee software onto the
device using the View Wireless App (see the View Wireless App manual).
To update the software on the device, the procedure is the same.
2) After conversion to Zigbee technology (or the software update), the actuator automatically
goes into pairing mode so that it can be recognised by the Amazon device within 5 minutes. If
the actuator is not in pairing mode, cut off the power supply and restore it after a few seconds.
3) Associate the actuator with Amazon Echo Plus, Echo Show or Echo Studio according to the
procedure envisaged by the voice assistant (see the Amazon documentation).
Set the actuator parameters.
1) Within the first 5 minutes after the device has been powered (already associated with Alexa),
press the front push button for 15 s; this way, you can select the relay operation - between
one-position stable and two-position stable (the LED flashes green for the two-position stable
setting and amber for the one-position stable setting).
2) Briefly press the front push button to switch from two-position stable to one-position stable
and vice versa; once the choice has been made, press the front push button for 5 s to confirm.
If you have set the two-position stable setting, the LED flashes green three times, whereas if you
have chosen the one-position stable setting, you will move on to the next step (3).
3) Press the front push button for 5 s to set the one-position stable activation time. Press the front
push button briefly, the output is activated and the LED lights up amber permanently; at the end
of the time you wish to set, press the front push button again. The output is deactivated and
the LED flashes amber for 3 times to confirm the setting made.
N.B. When the voltage returns after a power outage, the relay maintains the state in which it was
prior to the power supply cut out.
Summary of Zigbee technology mode signalling.
• During normal operation:
LED Meaning
On
(amber for Eikon, blue for Arké, green for Idea and
Plana)
Relay active
Off Relay not active
• In the configuration phase:
LED Meaning
Flashing white
(for max 5 min.)
Zigbee mode active pending
voice assistant
Flashing blue
(for max 2 min.)
Pending receipt of
a fw update
Blue permanently lit Device associated via Bluetooth
with the smartphone
Flashing green during
one-position/two-position stable config-
uration
(for max 5 min.)
Setting in two-position stable
Flashing amber during
one-position/two-position stable config-
uration
(for max 5 min.)
Setting in one-position stable
Amber permanently lit One-position stable time setting
Flashing green 3 times Confirms two-position stable setting
Flashing amber 3 times Confirms one-position stable setting
Flashing green rapidly
3 times
Device correctly
associated with the voice assistant
On
(amber for Eikon, blue for Arké,
green for Idea and Plana)
Relay active
during normal operation
CONTROLLABLE LOADS.
Loads Heating
100 V~ 16 A 8 A 30 W 0.5 A 4 A 16 (3.5) A
240 V~ 16 A 8 A 100 W 0.5 A 4 A 16 (3.5) A
RESETTING THE RELAY MODULE.
The reset restores the factory settings. Within the first 5 minutes from powering, press the front
push button for 30 s until LED flashes white.
INSTALLATION RULES.
• Installation must be carried out by qualified persons in compliance with the current regula-
tions regarding the installation of electrical equipment in the country where the products are
installed.
• The device must be installed in flush mounting boxes or surface mounting boxes with Eikon,
Arkè , Idea and Plana mounting frames and cover plates.
• Installation must be carried out in mounting boxes with a depth of more than 48 mm.
• The relay output power circuit must be protected against overloads by installing a device, fuse
or automatic 1-way switch, with a rated current not exceeding 16 A.
CHARACTERISTICS.
• Rated supply voltage: 100-240 V~, 50/60 Hz.
• Dissipated power: 0.85 W
• RF transmission power: < 100mW (20dBm)
• Frequency range: 2400-2483.5 MHz
•Terminals:
- 2 terminals (L and N) for line and neutral
- 1 terminal (1) for the relay output in voltage
• 1 front push button for load control and for configuration/reset.
If configured in the “Energy” application, it forces the output ton for the time set on the
View App.
• RGB LED indicating the output status (which can be set from the View Wireless App) and the
configuration status (flashing blue)
• In Bluetooth technology mode, you can associate up to 2 radio devices (art. 03925) which
make it possible to control the actuator or activate a scenario.
• Operating temperature: -10 ÷ +40 °C (indoor)

Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com
20593 02 2110
WEEE - User information
The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be collected separately
from other waste. The user must therefore hand the equipment at the end of its life cycle over to the appropriate municipal centres for the
differentiated collection of electrical and electronic waste. As an alternative to independent management, you can deliver the equipment you
want to dispose of free of charge to the distributor when purchasing a new appliance of an equivalent type. You can also deliver electronic
products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to electronics distributors with a sales area
of at least 400 m2. Proper sorted waste collection for subsequent recycling, processing and environmentally conscious disposal of the old
equipment helps to prevent any possible negative impact on the environment and human health while promoting the practice of reusing and/
or recycling materials used in manufacture.
• Protection degree: IP20
• Configuration from View Wireless App for Bluetooth technology system and Amazon App for
Zigbee technology.
• Controllable via View App.
OPERATION IN Bluetooth technology MODE.
The device operates by default in Bluetooth technology mode and this standard makes it possible
to associate the radio control 03925 which can be configured to control the actuator on-board
or to recall a scenario.
If configured in the “Energy” application, the radio control forces the output on (by pressing
the upper key) and removes the forcing (by pressing the lower key)
Through the use of gateway 20597-19597-16497-14597 the functions can be managed locally
or remotely via the View App, and the control is also available via the voice assistants Alexa,
Google Assistant and Siri.
The device is also compatible with Homekit.
N.B.: From fw version 1.7.0, the device works as a repeater node for battery-operated devices
(for instance art. 03980).
Settings.
The View Wireless App can be used to set the following parameters:
- RGB LED for backlighting: colour can be selected from a default list (default: amber for Eikon,
blue for Arké and green for Plana).
- LED brightness: off, low, medium, high for active load (default setting: high) and for load off
(default: off).
CONNECTIONS
FRONT AND BACK VIEW
L
N
20593
L N
μ
1
100-240V~
50/60Hz
16A
Relay output
L
N
L N
μ
1
100-240V~
50/60Hz
16A
1. Example of connection to the load 2. Example of connection to the socket outlet
L
N
20593
L N
μ
1
100-240V~
50/60Hz
16A
20210
VIMAR SPA
VIALE VICENZA 14
36063 MAROSTICA VI
ITALY
10 mm
LED
Front push button for load control
and configuration/reset
- Load cut-off threshold function: active or not active (default: not active).
- Consumption threshold for load cut-off (default: 3680 W).
- Load status when the voltage is restored: off, on or previous status (default: previous status).
- Relay operation: two-position stable or one-position stable (default: two-position stable).
- One-position stable activation time (default: 60 s).
REGULATORY COMPLIANCE.
RED Directive. RoHS directive.
Standards EN 60669-2-1, EN 301 489-17, EN 300 328, EN 62479, EN 50581.
Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text
of the EU declaration of conformity is on the product sheet available on the following website:
www.vimar.com
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
The Apple, iPhone and iPad logos are trademarks of Apple Inc., registered in the United States and in other Countries and
Regions. App Store is a service trademark of Apple Inc. Google is a trademark of Google LLC. Amazon, Alexa and all related
logos are trademarks of Amazon.com, Inc. or its affiliates.