Delta Electronics AC Drive VFD-F Series User manual

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
Preface
Thank you for choosing DELTA’s high-performance VFD-F Series. VFD-F Series are
manufactured by adopting high-quality components, material and incorporating the latest
microprocessor technology available.
Getting Started
This manual will be helpful in the installation, parameter setting, troubleshooting, and daily
maintenance of the AC motor drives. To guarantee safe operation of the equipment, read
the following safety guidelines before connecting power to the AC drives. Keep this
operating manual handy and distribute to all users for reference.
! WARNING
!Always read this manual thoroughly before using VFD-F series AC Motor Drives.
!Ensure that VFD-F is grounded in a correct way before putting it into use.
!DANGER! AC input power must be disconnected before any maintenance. Do not connect
or disconnect wires and connectors while power is applied to the circuit. Maintenance must
be performed by qualified technicians.
!CAUTION! There are highly sensitive MOS components on the printed circuit boards.
These components are especially sensitive to static electricity. To avoid damage to these
components, do not touch these components or the circuit boards with metal objects or
your bare hands.
!DANGER! A charge may still remain in the DC-link capacitor with hazardous voltages even
if the power has been turned off. To avoid personal injury, do not remove the cover of the
AC drive until all “DISPLAY LED” lights on the digital keypad are off. Please note that there
are live components exposed within the AC drive. Do not touch these live parts.
!CAUTION! Ground the VFD-F using the ground terminal. The grounding method must
comply with the laws of the country where the AC drive is to be installed. Refer to Basic
Wiring Diagram.
!DANGER! The AC drive may be destroyed beyond repair if incorrect cables are connected
to the input/output terminals. Never connect the AC drive output terminals U/T1, V/T2, and
W/T3 directly to the AC main circuit power supply.
!CAUTION! The final enclosures of the AC drive must comply with EN50178. (Live parts
shall be arranged in enclosures or located behind barriers that meet at least the
requirements of the Protective Type IP20. The top surface of the enclosures or barrier that
is easily accessible shall meet at least the requirements of the Protective Type IP40).
(VFD-F series corresponds with this regulation.)
!CAUTION! The rated voltage for the AC motor drive must be ≤240V for 230V models (≤
480V for 460V models) and the mains supply current capacity must be ≤5000A RMS
(≤10000A RMS for the ≥40hp (30kW) models)
CAUTION! Heat sink may heat up over 70oC (158oF), during the operation. Do not touch
the heat sink.

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
TABLE OF CONTENTS
CHAPTER 1 RECEIVING AND INSPECTIONS
1.1 Nameplate Information ........................................................................ 1 - 1
1.2 Model Explanation ............................................................................... 1 - 1
1.3 Serial Number Explanation.................................................................. 1 - 2
CHAPTER 2 STORAGE AND INSTALLATION
2.1 Storage................................................................................................. 2 - 1
2.2 Installation............................................................................................ 2 - 2
CHAPTER 3 WIRING
3.1 Basic Wiring Diagram .......................................................................... 3 - 2
3.2 External Wiring .................................................................................... 3 - 5
3.3 Main Circuit Connection ...................................................................... 3 - 6
3.4 Control Terminals................................................................................. 3 - 9
3.5 Specifications for Power Terminals and Control Terminals ................. 3 -11
3.6 Wiring Notes ........................................................................................ 3-14
3.7 Motor Operation Precautions .............................................................. 3-16
CHAPTER 4 DIGITAL KEYPAD OPERATION
4.1 VFD-PU01 ........................................................................................... 4 - 2
4.1.1 Description of the Digital Keypad VFD-PU01 ............................... 4 - 2
4.1.2 Explanation of Display Message................................................... 4 - 2
4.1.3 Operation Steps of the Digital Keypad VFD-PU01 ....................... 4 - 4

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
4.2 KPF-CC01 ........................................................................................... 4 - 5
4.2.1 Description of the Digital Keypad KPF-CC01 ............................... 4 - 5
4.2.2 Explanation of Display Message................................................... 4 - 5
4.2.3 KPF-CC01 Operation Flow Chart ................................................. 4 - 6
CHAPTER 5 DESCRIPTION OF PARAMETER SETTINGS
5.1 Group 0: AC Drive Status Parameters................................................. 5 - 1
5.2 Group 1: Basic Parameters ................................................................. 5 - 4
5.3 Group 2: Operation Method Parameters............................................. 5 - 9
5.4 Group 3: Output Function Parameters ................................................ 5-15
5.5 Group 4: Input Function Parameters ................................................... 5-19
5.6 Group 5: Multi-step Speed Frequency Parameters............................. 5-24
5.7 Group 6: Protection Parameters.......................................................... 5-30
5.8 Group 7: AC Drive and Motor Parameters .......................................... 5-36
5.9 Group 8: Special Parameters .............................................................. 5-39
5.10 Group 9: Communication Parameters............................................... 5-45
5.11 Group 10: PID Control Parameters ................................................... 5-60
5.12 Group 11: Fan and Pump Control Parameters.................................. 5-63
CHAPTER 6 MAINTENANCE AND INSPECTIONS
6.1 Periodic Inspection .............................................................................. 6 - 1
6.2 Periodic Maintenance .......................................................................... 6 - 1
CHAPTER 7 TROUBLESHOOTING AND FAULT INFORMATION........... 7 - 1

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
CHAPTER 8 SUMMARY OF PARAMETER SETTINGS ............................ 8 - 1
APPENDIX A SPECIFICATIONS ................................................................ A - 1
APPENDIX B ACCESSORIES
B.1 All Brake Resistors & Brake Units Used in AC Motor Drives .............. B - 1
B.1.1 Dimensions and Weights for Brake Resistors.............................. B - 3
B.1.2 Specifications for Brake Unit ........................................................ B - 5
B.1.3 Dimensions for Brake Unit............................................................ B - 6
B.2 AMD-EMI Filter Cross Reference........................................................ B - 8
B.3 AC Reactor .......................................................................................... B-10
B.3.1 AC Input Reactor Recommended Value ...................................... B-10
B.3.2 AC Output Reactor Recommended Value.................................... B-11
B.4 Non-fuse Circuit Breaker Chart ........................................................... B-12
B.5 Fuse Specification Chart ..................................................................... B-13
B.6 PU06.................................................................................................... B-14
B.6.1 Description of the Digital Keypad VFD-PU06............................... B-14
B.6.2 Explanation of Display Message .................................................. B-14
B.6.3 PU06 Operation Flow Chart ......................................................... B-15
B.7 Relay Card .......................................................................................... B-16
B.8 Zero Phase Reactor ............................................................................ B-18
APPENDIX C DIMENSIONS........................................................................ C - 1

1
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 1-1
CHAPTER 1 RECEIVING AND INSPECTION
This VFD-F AC drive has gone through rigorous quality control tests at the factory before
shipment. After receiving the AC drive, please check for the following:
Receiving
9Check to make sure that the package includes an AC drive, the User Manual, dust
covers and rubber bushings.
9Inspect the unit to insure it was not damaged during shipment.
9Make sure that the part number indicated on the nameplate corresponds with the part
number of your order.
1.1 Nameplate Information: Example for 7.5HP/5.5kW 3-phase 460V AC drive
MODEL : VFD055F43A
INPUT : 3PH 380-480V 50/60Hz 14A
OUTPUT : 3PH 0-480V 13 .9KVA 7.5HPA 9
Frequency Range : 1.5-120Hz
DELTA ELECTRONICS INC. MADE IN XXXXX
AC Drive Model
Input Spec.
Output Spec.
Output Frequency Range
Serial Number & Bar Code
Enclosure: TYPE 1
Enclosure type
055F43AT201001
1.2 Model Explanation
VFD
A
Version Type
43
Input Voltage
43:Three phase 460V
F
VFD-F Series
055
Applicable motor capacity
220: 30 HP(22kW)
300: 40HP(30kW)
055: 7.5HP(5.5kW)
075: 10 HP(7.5kW)
110: 15 HP(11kW)
750: 100HP(75kW)
Series
Name
150: 20HP(15kW)
370: 50HP(37kW)
450: 60HP(45kW)
550: 75HP(55kW)
900: 120HP(90kW)
1100: 150HP(110kW)
1320: 175HP(130kW)
23:Three phase 230V
007: 1.0HP(0.75kW)
015: 2.0HP(1.5kW)
022: 3.0HP(2.2kW)
037: 5.0HP(3.7kW)
1600: 215HP(160kW)
1850: 250HP(185kW)
2200: 300HP(220kW)

1
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
1-2
1.3 Series Number Explanation
Production number
3055F43A
Production model
460V 3-PHASE 7.5HP(5.5kW)
If there is any nameplate information not corresponding to your purchase order or any
problem, please contact your distributor.

2
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 2-1
CHAPTER 2 STORAGE AND INSTALLATION
2.1 Storage
The AC drive should be kept in the shipping carton before installation. In order to retain the
warranty coverage, the AC drive should be stored properly when it is not to be used for an
extended period of time.
Ambient Conditions:
Operation Air Temperature: -10oC to +40oC (14oF to 104oF)
+50oC (122oF) without dust cover.
Atmosphere pressure: 86 to 106 kPa
Installation Site Altitude: below 1000m
Vibration: Maximum 9.80 m/s2(1G) at less than 20Hz
Maximum 5.88 m/s2(0.6G) at 20Hz to 50Hz
Storage Temperature: -20oC to +60oC (-4oF to 140oF)
Relative Humidity: Less than 90%, no condensation allowed
Atmosphere pressure: 86 to 106 kPa
Transportation Temperature: -20oC to +60oC (-4oF to 140oF)
Relative Humidity: Less than 90%, no condensation allowed
Atmosphere pressure: 86 to 106 kPa
Vibration: Maximum 9.86 m/s2(1G) at less than 20Hz, Maximum 5.88
m/s2(0.6G) at 20Hz to 50Hz
Pollution Degree 2: good for a factory type environment.

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
2-2
2.2 Installation
CAUTION
The control, power supply and motor leads must be laid separately. They must not be
fed through the same cable conduit / trunking.
High voltage insulation test equipment must not be used on cables connected to the
drive.
Improper installation of the AC drive will greatly reduce its life. Be sure to observe the
following precautions when selecting a mounting location.
Failure to observe these precautions may void the warranty!
Do not mount the AC drive near heat-radiating elements or in direct sunlight.
Do not install the AC drive in a place subjected to high temperature, high humidity,
excessive vibration, corrosive gases or liquids, or airborne dust or metallic particles.
Mount the AC drive vertically and do not restrict the air flow to the heat sink fins.
The AC drive generates heat. Allow sufficient space around the unit for heat dissipation.
VFD-F
150mm
150mm
50mm
50mm
Air Flow
RU N
RESE T
STOP
JOG
STOP
U
RUN
F
H
REV
VFD-PU01
FWDJOG

3
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 3-1
CHAPTER 3 WIRING
DANGER
Hazardous Voltage
Before accessing the AC drive:
Disconnect all power to the AC drive.
Wait five minutes for DC bus capacitors discharge.
Any electrical or mechanical modification to this equipment without prior written
consent of Delta Electronics, Inc. will void all warranties and may result in a safety
hazard in addition to voiding the UL listing.
Short Circuit Withstand:
The rated voltage for the AC motor drive must be ≤240V for 230V models (≤
480V for 460V models) and the mains supply current capacity must be ≤
5000A RMS (≤10000A RMS for the ≥40hp (30kW) models)

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
3-2
3.1 Basic Wiring Diagram
Users must connect wires according to the following circuit diagram shown below. Do not
plug a Modem or telephone line to the RS-485 communication port, permanent damage may
result. Pins 1 & 2 are the power sources for the optional copy keypad and should not be
used while using RS-485 communication.
*RS-485
R(L1)
S(L2)
T(L3)
NFB
R
S
T
RB
RC
+1 +2/B1 B2
SA
OFF ON
MC
MC
E
1:+EV
2:GND
3:SG-
4:SG+
5:NC
6:NC
-
MI1
MI2
MI3
MI4
MI5
MI6
MI8
MI7
DCM
EF
AVI
ACI1
ACI2
ACM
Master Frequency
) 0~10V (47k
4~20mA
+10V
5k
3
2
1
Sw1
Sink
Source
E
NOTE
U(T1)
V(T2)
W(T3)
M
3~
RA1
RB1
RC1
E
A
FM1
ACM
Factory setting: output frequency
0~10Vdc/2mA
E
RA2
RB2
RC2
A
FM2
Factory setting: output current
0~20mA/4~20mA
500
Ω Max. Impedance:
RA3
RC3
RA4
RC4
RA5
RC5
RA6
RC6
RA7
RC7
RA8
RC8
Relay B.D.
RY00
4~20mA
0-10V
0-5V
SW2
FWD
REV
24V
Power Supply
+10V 20mA
For 230V series, 1~15HP models
460V series, 1~20HP models
Brake Resistor
(Optional)
Motor
NFB
FWD/STOP
REV/STOP
E.F.
Multi-step 1
Multi-step 2
Multi-step 3
Multi-step 4
RESET
JOG
Accel/Decel Prohibit
1/2 Accel/Decel Switch
Digital Signal Common
Factory
Setting
Factory Setting:
Sink Mode
Don't apply the mains voltage
directly to above terminals.
Multi-
function
Input
Terminals
Analog Signal Common
Serial Communication
Interface
Main circuit (power) terminals
Control circuit terminals
Shielded leads&cable
Optional
Please refer to the following
wiring for Sink mode and
Source mode.
240VAC 2.5A
120VAC 5A
28VDC 5A
Multi-function indication
output contacts
Factory setting: no function
Factory setting:
no function
Multi-function analog output terminals
Analog Signal Common
Recommended circuit
when power supply is
turned OFF by a fault
output.
If the fault occurs, the
contact will be ON to turn
off the power and protect the power system.

3
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 3-3
*RS-485
R(L1)
S(L2)
T(L3)
NFB
R
S
T
RB
RC
+1 +2
SA
OFF ON
MC
MC
E
1:+EV
2:GND
3:SG-
4:SG+
5:NC
6:NC
MI1
MI2
MI3
MI4
MI5
MI6
MI8
MI7
DCM
EF
AVI
A
CI1
A
CI2
ACM
Master Frequency
0~10V (47k )
4~20mA
+10V
5k
3
2
1
Sw1
Sink
Source
E
NOTE
U(T1)
V(T2)
W(T3)
M
3~
RA1
RB1
RC1
E
A
FM1
ACM
0~10Vdc/2mA
E
240VAC 2.5A
120VAC 5A
28VDC 5A
RA2
RB2
RC2
A
FM2
0~20mA/4~20mA
Max. Impedance: 500
Ω
RA3
RC3
RA4
RC4
RA5
RC5
RA6
RC6
RA7
RC7
RA8
RC8
Relay B.D.
RY00
4~20mA
0-10V
0-5V
SW2
FWD
REV
24V
1/2Accel/Decel Switch
Power Supply
+10V 20mA
PN
B1
B2
VFDB
-
For 230V series, 20HP and above models
460V series, 25HP and above models
Brake Unit (Optional)
Brake Resistor
(Optional)
Motor
NFB
FWD/STOP
REV/STOP
E.F.
Multi-step 1
Multi-step 2
Multi-step 3
Multi-step 4
RESET
JOG
Accel/Decel Prohibit
Digital Signal Common
Don't apply the mains voltage
directly to above terminals.
Multi-
function
Input
Te r m i na l s
Analog Signal Common
Serial Communication
Interface
Multi-function indication
output contacts
Factory setting: no function
Factory setting:
no function
Multi-function Analog Output Terminals
Factory setting: output frequency
Factory setting: output current
Analog Signal Common
Optional
Main circuit (power) terminals
Control circuit terminals
Shielded leads&cable
Recommended circuit
when power supply
is turned OFF by a
fault output.
If the fault occurs, the
contac t wi ll be ON to turn
off the power and protect the power system.
Factory setting: Sink Mode
Please refer to the following
wiring for Sink mode and
Source mode.
Factory
Setting

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
3-4
Wiring for SINK mode and SOURCE mode
JOG
1/2 Accel/Decel switch
MI7
MI8
Sw1
Sink
Source
JOG
1/2 Accel/Decel switch
MI7
MI8

3
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 3-5
3.2 External Wiring
R/L1 S/L2 T/L3
U/T1 V/T2 W/T3
B2
-
+/B1
E
E
BR
VFDB
BR
EMI Filter
Power Supply
FUSE/NFB
Magnetic
Contactor
Input AC
Line Reactor
Zero-phase
Reactor
BrakeResistor
(Optional)
BrakeUnit
(Optional)
Zero-phase
Reactor
Output AC
Line Reactor
Motor
Items Explanations
Power
supply
Please follow the specific power
supply requirements shown in
Appendix A.
Fuse/NFB
(Optional)
There may be an inrush current
during power up. Please check the
chart of Appendix B and select the
correct fuse with rated current. Use
of an NFB is optional.
Magnetic
contactor
(Optional)
Please do not use a Magnetic
contactor as the I/O switch of the AC
motor drive, as it will reduce the
operating life cycle of the AC drive.
Input AC
Line Reactor
(Optional)
Used to improve the input power
factor, to reduce harmonics and
provide protection from AC line
disturbances (surges, switching
spikes, short interruptions, etc.). AC
line reactor should be installed when
the power supply capacity is 500kVA
or more or advanced capacity is
activated. The wiring distance should
be≤10m. Refer to appendix B for
details.
Zero-phase
Reactor
(Ferrite Core
Common
Choke)
(Optional)
Zero-phase reactors are used to
reduce radio noise especially when
audio equipment is installed near the
inverter. Effective for noise reduction
on both the input and output sides.
Attenuation quality is good for a wide
range from AM band to 10MHz.
Appendix B specifies the zero-phase
reactor. (RF220X00A)
EMI filter
(Optional)
To reduce electromagnetic
interference, please refer to
Appendix B for more details.
Brake
Resistor
(Optional)
Used to reduce the deceleration time
of the motor. Please refer to the chart
in Appendix B for specific Brake
Resistors.
Output AC
Line Reactor
(Optional)
Motor surge voltage amplitude
depends on motor cable length. For
applications with long motor cable
(>20m), it is necessary to install a
reactor at the inverter output side.

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
3-6
3.3 Main Circuit Connection
Figure 1 for the main circuit terminals
R(L1)
S(L2)
T(L3)
R
S
T
U(T1)
V(T2)
W(T3)
IM
3~
MC
E
E
+1 +2/B1 B2
-
Brake Resistor
(Optional)
Motor
Non-fuse breaker
(NFB)
Figure 2 for the main circuit terminals
R(L1)
S(L2)
T(L3)
R
S
T
U(T1)
V(T2)
W(T3)
IM
3~
MC
E
E
VFDB
+1 +2
-
Brake Resistor (Optional)
Non-fuse breaker
(NFB)
Motor
Terminal Explanations
Terminal Symbol Explanation of Terminal Function
R/L1, S/L2, T/L3 AC line input terminals
U/T1, V/T2, W/T3 AC drive output terminals motor connections
+1,+2 Connections for DC Link Reactor (optional)
+2/B1~B2 Connections for Brake Resistor (optional)
+2~ -,+2/B1~ - Connections for External Brake Unit (VFDB series)
Earth Ground

3
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 3-7
Mains power terminals (R/L1, S/L2, T/L3)
Connect these terminals (R/L1, S/L2, T/L3) via a non-fuse breaker or earth leakage
breaker to 3-phase AC power (some models to 1-phase AC power) for circuit protection.
It is unnecessary to consider phase-sequence.
It is recommended to add a magnetic contactor (MC) in the power input wiring to cut off
power quickly and reduce malfunction when activating the protection function of AC
motor drives. Both ends of the MC should have an R-C surge absorber.
Please make sure to fasten the screw of the main circuit terminals to prevent sparks
which is made by the loose screws due to vibration.
Please use voltage and current within the regulation shown in Appendix A.
When using a general GFCI (Ground Fault Circuit Interrupter), select a current sensor
with sensitivity of 200mA or above, and not less than 0.1-second detection time to avoid
nuisance tripping. For the specific GFCI of the AC motor drive, please select a current
sensor with sensitivity of 30mA or above.
Do NOT run/stop AC motor drives by turning the power ON/OFF. Run/stop AC motor
drives by RUN/STOP command via control terminals or keypad. If you still need to
run/stop AC drives by turning power ON/OFF, it is recommended to do so only ONCE
per hour.
Do NOT connect 3-phase models to a 1-phase power source.
Output terminals for main circuit (U, V, W)
If the AC drive is installed in the place where a load reactor is needed, install the filter
close to U/T1, V/T2, W/T3 side of AC drive. Do not use a Capacitor or L-C Filter
(Inductance-Capacitance) or R-C Filter (Resistance-Capacitance), unless approved by
Delta.
DO NOT connect phase-compensation capacitors or surge absorbers at the output
terminals of AC motor drives.
Use well-insulated motor, suitable for inverter operation.
Terminals [+1, +2] for connecting DC reactor
+1
Jumper
DC reactor
To improve power factor and reduce harmonics, connect a DC reactor between
terminals [+1, +2]. Please remove the jumper before connecting the DC reactor.

VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
3-8
Terminals [+2/B1, B2] for connecting brake resistor and terminals [+2/B1, -] for
connecting external brake unit
Brake unit(optional)
Refer to Appendix B for the use of
special brake resistor/unit
+2/B1
B2
BR
+2/B1
-
VFDB
BR
Brake resistor(optional
)
Connect a brake resistor or brake unit in applications with frequent deceleration ramps,
short deceleration time, too low brake torque or requiring increased brake torque.
If the AC motor drive has a built-in brake chopper, connect the external brake resistor to
the terminals [＋2/B1, B2].
Some models of VFD-F series don’t have a built-in brake chopper, please connect an
external optional brake unit and brake resistor.
When not used, please leave the terminals [+2(+2/B1), -] open.
WARNING!
Short-circuiting [B2] or [-] to [+2/B1] can damage the AC motor drive.

3
VFD-F Series
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 3-9
3.4 Control Terminals
+24V
DCM
SINK/NPN Mode
Multi-function
Input Terminal
Internal Circuit
+24V
DCM
SOURCE/PNP Mode
Multi-function
Input Terminal
Internal Circuit
Terminal symbols and functions
Terminal Symbols Terminal Functions Factory Settings
FWD Forward-Stop command
REV Reverse-Stop command
EF External fault
MI1 Multi-function Input 1 Factory setting: Multi-step speed command 1
MI2 Multi-function Input 2 Factory setting: Multi-step speed command 2
MI3 Multi-function Input 3 Factory setting: Multi-step speed command 3
MI4 Multi-function Input 4 Factory setting: Multi-step speed command 4
MI5 Multi-function Input 5 Factory setting: RESET
MI6 Multi-function Input 6 Factory setting: JOG
MI7 Multi-function Input 7 Factory setting: Accel/Decel prohibit
MI8 Multi-function Input 8 Factory setting: Accel/Decel time switch 1
+24V DC Voltage Source (+24V, 20mA), used for source mode.
DCM Digital Signal Common Used as common for digital inputs and used
for sink mode.
RA 1 Multi-function Relay1
output (N.O.) a
RB 1 Multi-function Relay1
output (N.C.) b
RC 1 Multi-function Relay1
common
RA 2 Multi-function Relay2
output (N.O.) a
RB 2 Multi-function Relay2
output (N.C.) b
RC 2 Multi-function Relay2
common
1.5A(N.O.)/1A(N.C.) 240VAC
1.5A(N.O.)/1A(N.C.) 24VDC
Refer to Pr.03-00 to Pr.03-01