Delta Electronics Profibus Communication Module CME-PD01 User manual

2007-10-12
5011644101-PDT1
Profibus Communication Module (CME-PD01) Instruction Sheet
Profibus is a registered trademark of Profibus International.
Please thoroughly read and understand the following contents to ensure correct use before operation.
The content of this instruction sheet may be revised without prior notice. Please consult our distributors or
download the most updated version at http://www.delta.com.tw/industrialautomation
A. Panel Appearance
1: Reserved
2: EV
5: SG+
6: Reserved
7: Reserved
8: Reserved
3: GND
4: SG-
Profibus-DP
Interface (DB9)
RS-485 (RJ45)
ADDH ADDL
SPNET
CME-PD01
SP LED
NET LEDAddress Switches
1. SP LED: Indicating the connection status between
VFD-E and CME-PD01.
2. NET LED: Indicating the connection status between
CME-PD01 and PROFIBUS-DP.
3. Address Switches: Setting the address of
CME-PD01 on PROFIBUS-DP network.
4. RS-485 Interface (RJ45): Connecting to VFD-E, and
supply power to CME-PD01.
5. PROFIBUS-DP Interface (DB9): 9-PIN connector
that connects to PROFIBUS-DP network.
6. Extended Socket: 4-PIN socket that connects to
PROFIBUS-DP network.
B. Dimensions
57.3[2.26]
59.7[2.35]
3.6[0.14]
72.2 [2.84]
3.5 [0.14]34.8 [1.37]
ADDH ADDL
SPNET
CME-PB01
C. Parameters Setting in VFD-E
VFD-E
Baud Rate 9600 Pr.09.01=1
RTU 8, N, 2 Pr.09.04=3
Freq. Source Pr.02.00=3
Command Source Pr.02.01=3
D. Power Supply
The power of CME-PD01 is supplied from VFD-E. Please
connect VFD-E to CME-PD01 by using 8 pins RJ-45 cable,
which is packed together with CME-PD01. After connection
is completed, CME-PD01 is powered whenever power is
applied to VFD-E.
E. PROFIBUS Address
CME-PD01 has two rotary s select the PROFIBUS address.
The set value via 2 address switches, ADDH and ADDL, is
in HEX format. ADDH sets the upper 4 bits, and ADDL sets
the lower 4 bits of the PROFIBUS address.
Address Meaning
1..0x7D Valid PROFIBUS address
0 or 0x7E..0xFE Invalid PROFIBUS address
NOTE
Please download the GSD file and user manual at
http://www.delta.com.tw/industrialautomation/

Profibus 通訊模組（CME-PD01）說明書
Profibus 為Profibus international 註冊商標。
請詳細閱讀下列說明後才使用本產品，以確保使用安全。
由於產品精益求精，當內容規格有所修正時，請洽詢代理商或至台達網站
(http://www.delta.com.tw/ch/product/em/em_main.asp)下載最新版本。
A. 面板外觀
1: Reserved
2: EV
5: SG+
6: Reserved
7: Reserved
8: Reserved
3: GND
4: SG-
Profibus-DP
Interface (DB9)
RS-485 (RJ45)
ADDH ADDL SPNET
CME-PD01
SP LED
NET LEDAddress Switches
1. SP LED：變頻器與 CME-PD01 連接狀態指示
2. NET LED：CME-PD01 與PROFIBUS-DP 連接狀態
指示
3. 位址設定鈕：設定 CME-PD01 在PROFIBUS-DP
網路上的通信位址
4. RS-485 通訊口 (RJ-45)：與VFD-E 系列變頻器連
接並經由此 port 提供電源給 CME-PD01
5. PROFIBUS-DP 介面 (DB9)：用於連接
PROFIBUS-DP 網路
6. 並連插座：使用 4-PIN socket 連接 PROFIBUS-DP
網路
B. 外觀尺寸
57.3 [2.26]
59.7 [2.35]
3.6 [0.14]
72.2 [2.84]
34.8 [1.37]
ADDH ADDL
SPNET
CME-PB01
UNIT: mm(inch)
C. VFD-E 通訊參數的設定
VFD-E
Baud Rate 9600 Pr.09.01=1
RTU 8, N, 2 Pr.09.04=3
Freq. Source Pr.02.00=3
Command Source Pr.02.01=3
D. 電源供應
CME-PD01 電源由所連接之變頻器所供給，使用標準通訊傳
輸線(附於包裝盒內，連接 RJ-45，8pins) 連接變頻器和
CME-PD01，當變頻器上電後，電源即可輸入 CME-PD01。
E. 位址設定鈕
CME-PD01 提供兩個可旋轉之位址設定鈕來設定，其在
PROFIBUS-DP 網路上的通信位址。兩個旋鈕包括：ADDH
與ADDL，ADDH 用來設定高 4位元的通信位址，ADDL 用
來設定低 4位元的通信位址，並採用 16 進制。
通信位址 說明
1..0x7D 有效的 PROFIBUS 位址
0或0x7E..0xFE 無效的 PROFIBUS 位址
NOTE
請至台達網站下載 GSD 檔案及其使用手冊
http://www.delta.com.tw/ch/product/em/em_main.asp