Delta Electronics Pulse Generator Card PG-05 User manual

2007-07-16
5011626802-G5E
2
PG-05 Pulse Generator Card for VFD-V Series
Instruction Sheet
1-1 PG-05 Appearance
1-2 Explanations of the Terminals of PG-05 Card
Terminals Explanation
VP Output voltage of encoder: +5V±5% 200mA
DCM Common point of the power supply and the signal
A1,
B1,
Z1,
A1
B1
Z1
The input signal of encoder (select output type of the encoder
from FJP1).
The power supply can be single-phase or 2-phase. It can be
up to 500KP/Sec (max.).
A2,
B2,
A2
B2
Pulse (hand wheel and PLC) input (select input type from
FJP4).
The power supply can be single-phase or 2-phase. It can be
up to 500KP/Sec (max.).
AO,
BO,
ZO,
AO
BO
ZO
The output signal of encoder can set the dividing frequency by
using parameter 10-20.
The Max. output of Line drive is 50mA.
1-3 Wiring Examples
Wiring Diagram 1
MPG
FWD
REV
MI1
MI2
MI3
MI4
MI6
MI5
DCM
24V
FWD/STOP
REV/STOP
Multi-step2
Multi-step3
Multi-step4
Digital common
R/L1
S/L2
T/L3
Non-Fuse breaker
NFB
R
S
T
+1 +2/B1 B2
U/T1
V/T2
W/T3
M
3~
Braking Resistor(Option)
Motor
Multi-function input terminals
Factory Default
Jumper
Reset
E.F.
-
U
W
V
VP
DCM
A1
A1
B1
B1
Z1
Z1
PG
VP
DCM
A2
A2
B2
B2
Multi-step1
Incremental encoder
Line driver
Line driver
Main circuit (power) terminals Control circuit terminals Shielded leads & Cable
10-08
10-12
Hand wheel
AO
BO
ZO
AO
BO
ZO
Wiring Diagram 2
FWD
REV
Mi1
Mi2
Mi3
Mi4
Mi6
Mi5
DCM
24V
FWD/STOP
REV/STOP
Multi-step2
Multi-step3
Multi-step4
Digital common
R/L1
S/L2
T/L3
Non-Fuse breaker
NFB
R
S
T
+1 +2/B1 B2
U/T1
V/T2
W/T3
M
3~
Braking Resistor(Option)
Motor
Multi-functioninput terminals
Factory Default
Jumper
Reset
E.F.
-
U
W
V
VP
DCM
A1
A1
B1
B1
Z1
Z1
PG
DCM
A2
A2
B2
B2
Multi-step1
Incremental encoder
Line driver
Main circuit (power) terminals Control circuit terminals Shielded leads & Cable
EH-PLC
Y0
Y0
Y1
Y1
Y0
Y0
Y1
Y1
Phase difference 90
o
COM
AO
BO
ZO
AO
BO
ZO
1-4 Wiring Notes
1. Using the shielded wire to prevent interference, and do not line up in
parallel with circuits of AC200V or above.
2. Recommended wire size: 0.21~0.81mm2 (AWG24~AWG18).
3. Wire length (It is inversely proportional with signal frequency).
The Output Types
of the Encoder
Max. Wire
Length Wire Gauge
Voltage 50m
Open Collector 50m
1.25mm2(AWG18) or above
Line Driver 300m
Complementary 70m
1.25mm2(AWG18) or above
1-5 Installation
For 1-5HP For 7.5 HP and above
Step 1: Insert 3 PCB supports into control board.
Step 2: Press the PG card on the control board to be fixed to tighten the 3
screws with a torque of 4-6kgf-cm. If the PG card is not fixed on
the control board, it may cause screw idle running and cannot turn
the screw into supports.
1-6 The Corresponding Output Types of Encoder
Output Types of the
Encoder FJP1 FJP2
Voltage
O/P
0V
VCC
oc
TP
oc
TP
Open
Collector
O/P
0V
VCC
oc
TP
oc
TP
Line
Driver
Q
Q
oc
TP
oc
TP
Complementary
O/P
0V
VCC
oc
TP
oc
TP